Iso 7-2
在螺纹上形成压力密封连接的管螺纹 — 第2部分：通过极限量规进行验证
Pipe threads where pressure-tight joints are made on the threads — Part 2: Verification by means of limit gauges
查看详情 ↗原文资料
INTERNATIONAL STANDARDS LIBRARY
螺纹相关标准
Threads 与“螺纹”相关的标准资料，支持在当前标签内搜索。
标准 · 连接世界原文资料 / 双语简介 / 在线预览
当前范围：螺纹重置搜索 ↺
Iso 7-1
在螺纹上形成压力密封连接的管螺纹 — 第1部分：尺寸、公差和标记
Pipe threads where pressure-tight joints are made on the threads — Part 1: Dimensions, tolerances and designation
查看详情 ↗原文资料
DIN 264-2(1)
带间隙和扁平侧面的圆螺纹，螺距7毫米；尺寸极限和偏差 - 螺纹量规的公差和允许磨损
Round thread with clearance and flat flank with pitch 7 mm; limits of sizes and deviation - tolerances and permissible wear of thread gauges
查看详情 ↗原文资料
DIN 264-1
铁路车辆用单头及双头梯形螺纹（带间隙）- 第3部分：螺纹规、规尺寸及规的允许磨损
Trapezoidal threads, single and double start, with clearance, for rail vehicles - Part 3: Thread gauges, gauge dimensions and permissible wear of gauges
查看详情 ↗原文资料
DIN 263-3(1)
梯形螺纹，单头及双头，带间隙，用于轨道车辆 第3部分：螺纹规，规尺寸及规的允许磨损
Single- and double-start acme thread with clearance for rail vehicles — Part 3: Thread gauges — Thread dimensions and permissible wear of thread gauges
查看详情 ↗原文资料
DIN 263-2(1)
铁路车辆用单头及双头梯形螺纹（带间隙） 第2部分：螺纹极限尺寸和极限偏差
Single- and double-start acme thread with clearance for rail vehicles – Part 2: Thread limits and limit deviations
查看详情 ↗原文资料
DIN 263-1(1)
铁路车辆用单头及双头梯形螺纹（带间隙）- 第1部分：尺寸
Single- and double-start acme thread with clearance for rail vehicles – Part 1: Dimensions
查看详情 ↗原文资料
DIN 158-2
公制锥管外螺纹及配合的平行内螺纹 第2部分：量规和量规检验
Metric taper external and mating parallel internal screw threads Part 2: Gauges and gauging
查看详情 ↗原文资料
DIN 158-1(1)
公制锥外螺纹及配合的平行内螺纹 第1部分：尺寸、公差和检验
Metric taper external and mating parallel internal screw threads Part 1: Dimensions, tolerances and inspection
查看详情 ↗原文资料
din-76-3(1)
梯形螺纹、锯形螺纹、圆螺纹及其他粗牙螺纹的退刀和螺纹退刀槽
Run out and undercut for metric trapezoidal screw threads, knuckle screw threads, bulltress screw threads and other screw threads of coarse pitches
查看详情 ↗原文资料
din-76-2
符合ISO 228第1部分的管螺纹的螺纹收尾和螺纹退刀槽
Thread run-outs and thread undercuts for pipe threads conforming to ISO 228 Part 1
查看详情 ↗原文资料
din-76-1
DIN 76 第1部分：DIN 13 标准公制 ISO 螺纹的螺纹收尾和螺纹退刀槽
Run out and undercut for metric ISO threads according to DIN 13
查看详情 ↗原文资料
din-103-9(1)
ISO公制梯形螺纹 外螺纹和内螺纹的检验 量规尺寸和设计特征
ISO metric trapezoidal screw threads - Gauging of external and internal threads - Gauge dimensions and design features
查看详情 ↗原文资料
din-103-7(1)
公制ISO梯形螺纹 公称直径8至100mm螺栓螺纹的极限尺寸
ISO Metric Trapezoidal external screw threads from 8 to 100 mm diameter; limits
查看详情 ↗原文资料
din-103-3(1)
ISO公制梯形螺纹；通用梯形螺纹公差
ISO-metric trapezoidal screw threads; Tolerances for trapezoidal screw threads of general purpose
查看详情 ↗原文资料
显示第 1–20 条，共 20 条