JB/T 6457.1-2004 Small valve-regulated sealed lead-acid batteries Part 1: Product classification

This part specifies the model number, structural dimensions, terminal locations, specifications and overall dimensions of small valve-controlled sealed lead-acid batteries. JB/T 6457.1-2004 Small valve-regulated sealed lead-acid batteries Part 1: Product classification JB/T6457.1-2004 Standard download and decompression password: www.bzxz.net

ICS29.220.20
Machinery Industry Standard of the People's Republic of China
JB/T6457.1—2004
replaces JB/T6457.1—1992
Small-sized valve-regulated lead-acid batteries
Part 1: Product classification
purpose lead-acid batteries, valve-regulated types, Part2: Dimensions, terminals and marking, MOD) released on 2004-02-10
implemented on 2004-06-01
Foreword released by the National Development and Reform Commission of the People's Republic of China
Normative reference documents
Model preparation.||tt ||Structural dimensions
Terminal position
Specifications and overall dimensions
JB/T 6457.1—2004
JB/ T6457.1--2004
Foreword
JB/T6457-2004 "Small valve-regulated sealed lead-acid battery" is divided into two parts: - Part 1: Product Category: ||tt| |Part 2: Technical Conditions.
This part is Part 1 of JB/T6457.1-2004, corresponding to IEC61056-2-2002 "Portable lead-acid batteries (valve-regulated) Part 2: Dimensions, terminals and markings", this The degree of consistency with IEC61056-2-2002 is modified and adopted. Compared with JB/T6457.1-1992, the main changes in this standard are as follows: 1. Add a preface:
Modify the scope of application:
Add product models and types,
This part is developed by China Proposed by the Machinery Industry Federation. This part is under the jurisdiction of the National Lead-Acid Battery Standardization Technical Committee. This section was drafted by: Shenyang Battery Research Institute, Fujian Quanzhou Dahuaxin Battery Company, Fujian Anxi Minhua Battery Company, Quzhuo Shengyang Power Co., Ltd., Nanjing Zhenhuan Jinhui Colloidal Battery Company. The main drafters of this section: Fu Yanling, Wan Shaobo, Lin Jinshu, Zhou Qingshen, Qian Xuehai. The previous versions of the standard replaced by this part are: JB/T6457.1-1992.
1 range
Small valve-regulated sealed lead-acid battery
Part 1: Product Classification
JB/T6457.1—2004
JB6457 This part specifies the model number, structural dimensions, terminal positions, specifications and overall dimensions of small valve-regulated sealed lead-acid batteries (hereinafter referred to as battery).
This section applies to emergency lighting equipment, uninterruptible power supplies, mobile measurement equipment, etc., with various DC power supply batteries with a rated capacity of 65Ah or less (including 65Ah). The single cells of this type of lead-acid battery pack can have flat electrodes installed in square slots, or they can have wound electrodes installed in round cylinders. The sulfuric acid electrolyte in the cyanine battery is stagnant, or is adsorbed in the microporous structure between the electrodes or in a colloidal state.
2 Normative reference documents
The provisions in the following documents become the provisions of this part through the reference of this part of JB/T6457. All subsequent amendments (excluding corrigenda) or revisions of dated reference documents do not apply to this section. However, parties to an agreement based on this section are encouraged to study whether the latest versions of these documents can be used. For undated referenced documents, the latest version applies to this section.
JB/T2599 lead-acid battery product model compilation method 3 model compilation
Compiled according to JB/T2599, the product type and feature code is determined to be the Chinese pinyin "FM". Model meaning:
Structural dimensions
See Figure 1 for the rectangular structure and Figure 2 for the cylindrical structure. Figure
20h rate rated capacity, unit is Ah
sealed type
wide control type
number of single batteries connected in series||tt| |JB/T6457.1—2004
5 terminal positions
Figure 2
The terminal positions are divided into six types, as shown in Figures 3 to 8: the specific selection can be negotiated between the user and the manufacturer. +
Picture 3
6 Specifications and dimensions
Picture 4
Picture 5
Picture 6
Figure 7Www.bzxZ.net
Figure 8
Battery specifications and dimensions are divided into two types: rectangular and cylindrical. See Table 1 for rectangular specifications and dimensions, and Table 2 for cylindrical specifications and dimensions.
Note: If the specifications and sizes are not listed in the table, the user can negotiate with the manufacturer. Table 1
3-FM-1.0
3-FM-3.4
60|| tt||60
95||tt| |h
Maximum overall dimensions
L|| tt||50
72||tt| |153
20h rated case quality
2.0|| tt||3.0
3-FM-7.0
3-FM-10
3-FM-12
3-FM-20
4-FM-3.0
6-FM-3.0
6-FM-7.0
6-FM-10
6-FM-12
6-FM-15
6-FM-17
6-FM-24
6-FM-31
6-FM-38
6-FM-60
6~FM-65
Model||tt| |FM-2.5
103||tt ||134
134| |tt||134
137||tt ||176
表1（结）
最作发明二動
62| |tt||63
169||tt ||170
最作发动在线|| hr||mm||hr||h||hr||61||hr||72||hr||123||hr||158||hr||6||hr||58||hr| |52
100|| tt||78
D||tt| |34
181|| tt||197
184||tt| 177. Ah
1.2| |tt||1.9
7.0||tt ||10
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.