GB/T 5015-2003 Elastic pin gear coupling

This standard specifies the types, basic parameters and main dimensions of LZ, LZD, LZJ and LZZ elastic pin gear couplings, and gives technical requirements, inspection rules, marking, packaging and storage. GB/T 5015-2003 Elastic pin gear coupling GB/T5015-2003 Standard download decompression password: www.bzxz.net

This standard is a revision of GB/T5015-1985 "Elastic Pin Gear Coupling". The main changes of this standard compared with GB/T5015-1985 are as follows: the nominal torque and allowable speed have been readjusted and slightly improved; the coupling model has been modified according to GB/T12458 "Coupling Classification"; - some external dimensions have been changed, and the dimensions that must be available when selecting couplings have been added; the original Appendix A "Selection Instructions for Elastic Pin Gear Couplings" has been deleted. This standard was proposed and managed by the National Technical Committee for Standardization of Machine Shafts and Accessories. The drafting units of this standard: Mechanical Science Research Institute, Deyang Erzhong Basic Parts Factory. The main drafters of this standard: Ming Cuixin, Wang Jiannong, Gao Wen, Liu Xueguang. The previous versions of the standards replaced by this standard are: - GB/T5015-1985.
GB/T5015—2003
1 Scope
Elastic pin-tooth coupling
GB/T 5015—2003
This standard specifies the types, basic parameters and main dimensions of LZ, LZD, LZJ and LZZ elastic pin-tooth couplings (hereinafter referred to as couplings), and gives technical requirements, inspection rules, marking, packaging and storage. This standard is applicable to transmission shaft systems that connect two coaxial lines, and has the performance of compensating the relative offset of the two shafts and general vibration reduction. The working temperature is -20℃～+70℃, and the nominal torque transmitted is 112N·m～2800000N·m. 2 Normative references
The clauses in the following documents become the clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to an agreement based on this standard are encouraged to investigate whether the latest versions of these documents can be used. For any undated referenced document, the latest version applies to this standard. Pictorial markings for packaging, storage and transportationbZxz.net
GB/T 191
GB/T 699
GB/T 3852
GB/T4879
GB/T 5783
GB/T 6388
High-quality carbon structural steel
Shaft hole and connection type and size of coupling
Rust-proof packaging
Hexagon head bolt with full thread
Marks for shipping and receiving of transport packaging
GB/T 11352
GB/T 12458
GB/T13384
3 Classification
Casting carbon steel parts for general engineering
Classification of couplings
General technical conditions for packaging of electromechanical products
Couplings are divided into four types, see Table 1.
3.2 Model marking
The model and marking of couplings shall comply with the provisions of GB/T12458. Table 1
Coupling type
Type code
Elastic pin
Gear coupling
Elastic pin with tapered shaft hole
Gear coupling
GB/T5015—2003
Type code
Elastic pin connected to intermediate shaft
Gear coupling
Elastic pin with brake wheel
Gear coupling
Basic parameters and main dimensions
Table 1 (continued)
The basic parameters and main dimensions of 4.1LZ type elastic pin gear coupling shall comply with the requirements of Figure 1 and Table 2. Symbol
Y-type shaft hole
Ji-type shaft hole
JI-type shaft hole
Figure 1 LZ-type elastic pin-gear coupling
Y-type shaft hole
Nominal torque
T,/(N·m)
Permissible speed
[n]/(r/min)
Table 2 LZ-type elastic pin-gear coupling
Shaft hole diameter
dt, dz
Shaft hole length L
GB/T5015—2003
Unit: mm
Moment of inertia
I/(kg m2)
GB/T 5015—2003
Nominal torque
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
130112
Unit: mm
Moment of inertia
I/(kg·m2)
Nominal torque
T./(N· m)
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
3351220
GB/T5015—2003
Unit: mm
Moment of inertia
I/(kg·m2)
GB/T 5015--2003
Nominal torque
100000
125000
160000
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
Unit: mm
Moment of inertia
I/(k g·m2)
Nominal torque
T./(N·m)
250000
355000
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
8601605
695322
GB/T 5015—2003
Unit: mm
Moment of inertia
I/(kg·m2)
GB/T5015—2003
Nominal torque
T./(N· m)
630000
1120000
1800000
2240000
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
800355
1020360
Unit: mm
Moment of inertia
I/(kg·m2)
Nominal torque
Permissible speed
Th/(N·m)EnJ/(r/min)
LZ222 240 000
Shaft hole diameter
Table 2 (continued)
Shaft hole length L
1 5201 100
16401240
Note 1: Mass and moment of inertia are calculated according to Y/J, shaft hole combination type and minimum shaft hole diameter. Note 2: Short-term overload shall not exceed 2 times of nominal torque T, value. B
GB/T5015—2003
Unit is mm
Moment of inertia
I/(kg·m2)
4.2The basic parameters and main dimensions of LZD tapered shaft hole elastic pin gear coupling shall comply with the provisions of Figure 2 and Table 3. R
Y-type shaft hole
J, type shaft hole
Z1 type shaft hole
Figure 2LZD type tapered shaft hole elastic pin gear coupling weight
GB/T 5015—2003
Nominal torque
Permissible speed
Table 3LZD type tapered shaft hole elastic pin gear coupling shaft hole diameter
En]/(r/min)
Shaft hole length L
JI, ZI type
Unit: mm
Moment of inertia
1/(kg·ma)
Nominal torque
Tn/(Nm)
11 200
Permissible speed
[n]/(r/min)
Shaft hole diameter
Table 3 (continued)
Shaft hole length L
Y type JI, Z type
260160
GB/T 5015—2003
Unit: mm
Moment of inertia
I/(kg· m2)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.