JB/T 6013-2000 Technical Specifications for Low-pressure Metal Oil Pipe Assemblies for Diesel Engines

JB/T 6013-2000 This standard is a revision of JB/T 6013-1992 "Low-pressure Metal Oil Pipes and Joints for Diesel Engines". This standard specifies the structural type, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of low-pressure metal oil pipes and joints for diesel engines. This standard applies to diesel engine low-pressure oil pipe components with a cylinder diameter within 200mm. Its basic pressure is 2.5MPa, and its basic diameter is in the range of 3~25mm. This standard was first released as GB 3540~3541-83 in March 1983, and was revised for the first time as JB/T 6013-92 in May 1992. JB/T 6013-2000 Technical conditions for diesel engine low-pressure metal oil pipe components JB/T6013-2000 Standard download and decompression password: www.bzxz.net

ICS27.020
Machinery Industry Standard of the People's Republic of China
JB/T6013-2000
Diesel engine
Low-pressure metal oil pipe Components
Technical Conditions
Diesel enginesRequirements for lowpressurehydraulicpipeassesmies2000-08-31 Release
National Machinery Industry Bureau
Release
2001-01-01 Implementation|| tt||JB/T6013-2000
Foreword
This standard is a revision of JB/T6013-92 "Low-pressure Metal Oil Pipes and Joints for Diesel Engines". During the revision, only editorial changes were made to the original standard, and the main technical content remained unchanged. This standard will replace JB/T
601392
from the date of implementation. This standard is proposed and centralized by the National Internal Combustion Engine Standardization Technical Committee. This standard was drafted by: Shanghai Internal Combustion Engine Research Institute. The main drafters of this standard: Qu Junming and Chen Linshan. This standard was first published in March 1983 and revised for the first time in May 1992. 1Scope
Machinery Industry Standard of the People's Republic of China
Diesel Engine
Low-pressure Metal Oil Pipe Assemblies
Technical Conditions
DieselmginesRequirementsfor lowpressure hydraulicpipe assembliesJB/T6013—2000|| tt||Replaces JB/T6013-92
This standard specifies the structural type, technical requirements, test methods, inspection rules and markings, packaging, transportation and Storage. This standard applies to diesel engine low-pressure oil pipe components with a cylinder diameter within 200mm. Its basic pressure is 2.5MPa, and its basic diameter is in the range of 3~25mm.
2 Reference standards
The provisions contained in the following standards constitute provisions of this standard by being quoted in this standard. At the time of publication, the editions indicated were valid. All standards are subject to revision and parties using this standard should explore the possibility of using the latest version of the standard listed below. GB/T 699—1999
GB/T 2040—1989
GB/T2828—1987
GB/T3821—1983
GB/T8163—1999||tt ||3 structural types
High-quality carbon structural steel
Pure copper plate
Batch-by-batch inspection and counting sampling procedures and sampling tables (suitable for continuous batch inspection) Cleanliness determination of small and medium-power internal combustion engines Methods Seamless steel pipes for transporting fluids
Low-pressure oil pipe components are divided into different structural types according to their structural types: one-ball screw-in pipe joints;
Type A-
one-ball intermediate pipe joints:
Type B—
Type C—
Articulated pipe joint;
D type
Articulated short tee joint;||tt| |E-type one-to-one articulated long tee pipe joint.
3.1A type low-pressure oil pipe assembly
3.1.1 The structure and combined dimensions are as specified in Figure 1 and Table 1. National Machinery Industry Bureau approved on 2000-08-31 for implementation on 2001-01-01
Basic diameter
6|| tt||8
14(13)
Marking example:
embedded with pipe
JB/T6013 -2000
1 - spherical pipe section; 2 - jacket nut; 3 - screw-in joint Figure 1A type low pressure oil pipe assembly
Table 1
Pipe outer diameter
6.2|| tt||8.2
6||tt| |8
Type A low-pressure oil pipe assembly with an outer diameter of 10mm, marked: d
M10x1||tt ||M2×1.25
Low-pressure metal oil pipe assembly JB/T6013| |tt||3B10
3.1.2 The structure and dimensions of the spherical pipe section shall be as specified in Figure 2 and Table 2. 3
Figure 2 Spherical tube section
Type A
44|| tt||48
its will
Type B
Basic path
14(13)
Marking example:
Pipe outer diameter
dar| |tt||6
6.2||tt ||8.2
8.5||tt ||10.6
A spherical pipe section with an outer diameter of 10mm, marked as: spherical pipe section| |tt||3.1.3
6013—2000
Table 2
8||tt| |10
JB/T6013-10
The structure and dimensions of the jacket nut are as specified in Figure 3 and Table 3. 0.08B
Figure 3
Basic path||tt ||Dg
14(13)
Pipe outer diameter
D|| tt||M12×125-cH
M6×1.5-6H
M8X1.5-@H
ME0× 1.5-cH
M4×1.5-H| |tt||M7X1.5-QH
Coat Nut
Table 3
6| |tt||7
Find editor 12.5
18-027
24-833
41-038
15|| tt||16
Marking example:
JB/T6013—2000
The outer sleeve nut with an outer diameter of 10mm is marked as: outer sleeve nut JB/T6013-10
3.1.4 The structure and dimensions of the screw-in joint shall be in accordance with the requirements of Figure 4 and Table 4. Ao
Two increases
Figure 4 Screw-in connector
Table 4
Distance
14（13)
Outer diameter
Marking example:
d||t t||M2×1.25-6g
M16×1.25-6g
M8×1.5-6g
M2O×1.5-g
MD4×1.5-6g
ME7×1.5-6g
M0×1-6g
M12×1.25-6g
M14×15-6g
M16×15-6g
M20×15-6g
M24×156g
Di||tt| |4
The screw-in connector with a pipe outer diameter of 10 mm is marked as: D
Screw-in connector JB/6013-10
3.2B type low pressure oil pipe assembly
3.2.1 The structure and combination dimensions shall be in accordance with the provisions of Figure 5 and Table 14
18 -027
24 -033
36 -062
Marking example:
Connect with pipe
6013—2000
Weld with pipe
1-ball pipe joint: 2-jacket nut: 3-intermediate joint Figure 5 B-type low-pressure oil pipe assembly
B-type low-pressure oil pipe assembly with an outer diameter of 10mm is marked as: low-pressure metal oil pipe assembly JB/T6013
3.2.2 The structure and size of the ball pipe joint shall comply with the provisions of Figure 2 and Table 2. 3.2.3 The structure and size of the jacket nut shall comply with the provisions of Figure 3 and Table 3. 3.2.4 The dimensions of the intermediate joints shall be in accordance with the provisions of Figure 6 and Table 5. True #125
Figure 6 Intermediate joint
Table 5
14 (13)
Outer diameter
8||tt| |10
M2×1.25-6g
MI6×1.5-6g
M18×1.5-6g
MLO×1.5-g
MD4×1.56g
MD7× 1.56g
L||tt| |13.5
18-027
24 033
27 -033
30 ~033
36 -062
Marking example:
JB/T6013—2000
An intermediate joint with a pipe outer diameter of 8mm is marked: intermediate joint
JB /T6013-8
3.3C type low-pressure oil pipe assembly
3.3.1 The structure and combined dimensions are as specified in Figure 7 and Table 6. 1 - hinged bolt; 2 hinged pipe joint; 3 washer Figure 7C type low pressure oil pipe assembly
Table 6
Basic diameter Dg
4|| tt||6
20|| tt||(23)
Pipe outer diameter 4
12 (13)
M10×1
M12×1.25
M14X×15
M16X15
M18X15
M20X15
M22X15
M24x15
M7X2 (M27×1.5)
M30× 2
M33× 2
Note: In this standard, the specifications in brackets are not recommended (the same below). Marking examples:
C-type low-pressure oil pipe assembly with a pipe outer diameter of 10mm, marked: 18
20||tt| |23
Low-pressure metal oil pipe assembly JB/T6013
8|| tt||9
19||tt| |20
JB/T6013-2000
3.3.2 Hinge bolts The structure and dimensions are as specified in Figure 8 and Table 7. B02
25||tt| |Tube
Outer diameter
12 (13)|| tt||(14)
mark Example:
M8×1-6g
M10×1-6g
M12×12.5-6g
M14×15-6g|| tt||M16×15-6g
M18×15-6g
M20×15-6g
M22×15-6g
M34×15-6g|| tt||M27×2-6g
（M27×1.5)
M30×2-6g
M33×2-6g
12|| tt||15
Figure 8 Hinge Bolts
Table 7
54|| tt||58
35||tt| |38
Hinged bolts with diameter d of M14×1.5, marked as: H
10±035
10±035
12±035
13±035
14± 035
10||tt| |11
3M14×1.5||tt| |Hinged bolts
JB/T6013
The structure and dimensions of the hinged pipe joint body are in accordance with Figure 9 and Table 8. 3.3.3
22.78||tt| |26.17
13 -027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033
34 -862
36 -062
41-062
33.2|| tt||38
1.5||tt| |1.5
1. The structure and combined dimensions are as specified in Figure 7 and Table 6. 1 - hinged bolt; 2 hinged pipe joint; 3 washer Figure 7C type low pressure oil pipe assembly
Table 6
Basic diameter Dg
4|| tt||6
20|| tt||(23)
Pipe outer diameter 4
12 (13)
M10×1
M12×1.25
M14X×15
M16X15
M18X15
M20X15
M22X15
M24x15
M7X2 (M27×1.5)
M30× 2
M33× 2
Note: In this standard, the specifications in brackets are not recommended (the same below). Marking examples:
C-type low-pressure oil pipe assembly with a pipe outer diameter of 10mm, marked: 18
20||tt| |23
Low-pressure metal oil pipe assembly JB/T6013
8|| tt||9
19||tt| |20
JB/T6013-2000
3.3.2 Hinge bolts The structure and dimensions are as specified in Figure 8 and Table 7. B02
25||tt| |Tube
Outer diameter
12 (13)|| tt||(14)
mark Example:
M8×1-6g
M10×1-6g
M12×12.5-6g
M14×15-6g|| tt||M16×15-6g
M18×15-6g
M20×15-6g
M22×15-6g
M34×15-6g|| tt||M27×2-6g
（M27×1.5)
M30×2-6g
M33×2-6g
12|| tt||15
Figure 8 Hinge Bolts
Table 7
54|| tt||58
35||tt| |38
Hinged bolts with diameter d of M14×1.5, marked as: H
10±035
10±035
12±035
13±035
14± 035
10||tt| |11
3M14×1.5||tt| |Hinged bolts
JB/T6013
The structure and dimensions of the hinged pipe joint body are in accordance with Figure 9 and Table 8. 3.3.3
22.78||tt| |26.17
13 -027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033
34 -862
36 -062
41-062
33.2|| tt||38
1.5||tt| |1.5
1. The structure and combined dimensions are as specified in Figure 7 and Table 6. 1 - hinged bolt; 2 hinged pipe joint; 3 washer Figure 7C type low pressure oil pipe assembly
Table 6
Basic diameter Dg
4|| tt||6
20|| tt||(23)
Pipe outer diameter 4
12 (13)
M10×1
M12×1.25
M14X×15
M16X15
M18X15
M20X15
M22X15
M24x15
M7X2 (M27×1.5)
M30× 2
M33× 2
Note: In this standard, the specifications in brackets are not recommended (the same below). Marking examples:
C-type low-pressure oil pipe assembly with a pipe outer diameter of 10mm, marked: 18
20||tt| |23
Low-pressure metal oil pipe assembly JB/T6013
8|| tt||9
19||tt| |20
JB/T6013-2000
3.3.2 Hinge bolts The structure and dimensions are as specified in Figure 8 and Table 7. B02
25||tt| |Tube
Outer diameter
12 (13)|| tt||(14)
mark Example:
M8×1-6g
M10×1-6g
M12×12.5-6g
M14×15-6g|| tt||M16×15-6g
M18×15-6g
M20×15-6g
M22×15-6gbzxz.net
M34×15-6g|| tt||M27×2-6g
（M27×1.5)
M30×2-6g
M33×2-6g
12|| tt||15
Figure 8 Hinge Bolts
Table 7
54|| tt||58
35||tt| |38
Hinged bolts with diameter d of M14×1.5, marked as: H
10±035
10±035
12±035
13±035
14± 035
10||tt| |11
3M14×1.5||tt| |Hinged bolts
JB/T6013
The structure and dimensions of the hinged pipe joint body are in accordance with Figure 9 and Table 8. 3.3.3
22.78||tt| |26.17
13 -027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033
34 -862
36 -062
41-062
33.2|| tt||38
1.5||tt| |1.5
M30× 2
M33× 2
Note: Specifications in brackets in this standard are not recommended (the same applies below) Marking example:
C-type low-pressure oil pipe assembly with an outer diameter of 10mm is marked as: 18
Low-pressure metal oil pipe assembly JB/T6013
8||tt| |9
JB/T6013-2000
3.3.2 The structure and dimensions of the hinge bolts shall be in accordance with the requirements of Figure 8 and Table 7. B02
Distance
Outer diameter
12（13）
(14)| |tt||16
Marking example:
M8×1-6g
M10×1-6g
M12×12.5-6g
M14×15-6g
M16×15-6g
M18×15-6g
M20×15-6g
M22×15-6g
M34×15- 6g
M27×2-6g
（M27×1.5)
M30×2-6g
M33×2-6g
Figure 8 Articulated bolt
Table 7
19| |tt||22
The hinge bolt with diameter d of M14×1.5 is marked as: H
10±035
10±035
12±035
13±035
14± 035
3M14×1.5
Articulated bolt
JB/T6013
The structure and dimensions of the articulated pipe fitting body shall be in accordance with the requirements of Figure 9 and Table 8. 3.3.3
13-027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033
34 -862
36 -062
41-062
M30× 2
M33× 2
Note: In this standard, the specifications in brackets are not recommended (the same as below) Marking example:
Pipe outer diameter It is a 10mm C-type low-pressure oil pipe assembly, marked: 18
35| |tt||38
Low-pressure metal oil pipe assembly JB/T6013
3C10||tt ||6
1| |tt||1
2||tt ||2
JB/T6013-2000
3.3.2 The structure and dimensions of hinge bolts shall be as specified in Figure 8 and Table 7. B02
25||tt| |Tube
Outer diameter
12 (13)|| tt||(14)
mark Example:
M8×1-6g
M10×1-6g
M12×12.5-6g
M14×15-6g|| tt||M16×15-6g
M18×15-6g
M20×15-6g
M22×15-6g
M34×15-6g|| tt||M27×2-6g
（M27×1.5)
M30×2-6g
M33×2-6g
12|| tt||15
Figure 8 Hinge Bolts
Table 7
54|| tt||58
35||tt| |38
Hinged bolts with diameter d of M14×1.5, marked as: H
10±035
10±035
12±035
13±035
14± 035
10||tt| |11
3M14×1.5||tt| |Hinged bolts
JB/T6013
The structure and dimensions of the hinged pipe joint body are in accordance with Figure 9 and Table 8. 3.3.3
22.78||tt| |26.17
13 -027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033
34 -862
36 -062
41-062
33.2|| tt||38
1.5||tt| |1.5
M14×15-6g
M16×15-6g
M18×15-6g
M20×15-6g
M22× 15-6g
M34×15-6g
M27×2-6g
（M27×1.5)
M30×2-6g
M33× 2-6g
28| |tt||30
18||tt ||8
20 ||tt| |2
diameterd for M14×1.5的团接螺梶，结果的：H
10±035| |tt||10±035
12±035
13±035
14± 035
8| |tt||9
19||tt 3.3. .3
13- 027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033| |tt||34 -862
36 -062
41-062
11.5| |tt||14.5
33.2||tt ||38
7| |tt||5-6g
M14×15-6g
M16×15-6g
M18×15-6g
M20×15-6g
M22× 15-6g
M34×15-6g
M27×2-6g
（M27×1.5)
M30×2-6g
M33× 2-6g
15||tt|> ||L
28| |tt||30
18||tt ||8
20 ||tt| |2
diameterd for M14×1.5的团接螺梶，图像的：H
10±035| |tt||10±035
12±035
13±035
14± 035
8| |tt||9
19||tt 3.3. .3
13- 027
16 -027
18 -027
21 -033
24 -33
27 -033
30 -033| |tt||34 -862
36 -062
41-062
11.5| |tt||14.5
33.2||tt ||38
7| |tt||
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.