JB/T 7941.2-1995 Screw-in round oil cup
time:
1996-04-14 15:00:00
- JB/T 7941.2-1995
- in force
Standard ID:
JB/T 7941.2-1995
Standard Name:
Screw-in round oil cup
Chinese Name:
旋入式圆形油杯
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1996-04-14 -
Date of Implementation:
1996-04-14
China Standard Classification Number:
Machinery>>General Parts>>J21 Lubrication and Lubrication Devices
alternative situation:
Original standard number GB 1160.2-89
Drafter:
Chen Huajin, Zhang JiadeDrafting Organization:
Shanghai Mechanical and Electronic Industry Administration Bureau Science and Technology Information Institute, Mechanical and Electronic Industry Ministry Mechanical Standardization InstituteFocal point Organization:
Mechanical Standardization Institute of the Ministry of Machinery and Electronics IndustryProposing Organization:
Ministry of Machinery and Electronics IndustryPublishing Department:
Ministry of Machinery Industry of the People's Republic of China
Description (Translated English) / downloadSkip to download
Summary:
This standard specifies the type and size of screw-in round oil mark. This standard is applicable to oil marks used to observe the oil level of lubricating oil on various mechanical equipment. JB/T 7941.2-1995 Screw-in round oil cup JB/T7941.2-1995 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
Machinery Industry Standard of the People's Republic of China
JB/T7941.2—1995
Put-in round oil mark
Oil level indicators screwing round type1996-04-14Promulgated
Ministry of Machinery Industry of the People's Republic of China
Implementation on 1996-04-14
Mechanical Industry Standard of the People's Republic of China
Screw-in round oil mark
Oil level indicators screwing round typeSubject content and scope of application
This standard specifies the type and size of screw-in round oil marks. This standard is applicable to oil marks used to observe the oil level of lubricating oil on various mechanical equipment. 2 Reference standards
GB1163
3 Types and dimensions
Oil mark technical conditions
The sleeve mark is divided into two types: A and B: Type A see Figure 1. Type B see Figure 2. Dimensions see the table below Type A is used as an oil level indicator, and Type B is used to indicate the working condition of the oil. A
Approved by the Ministry of Machinery Industry on April 14, 1996
JB/T7941.2-1995Www.bzxZ.net
Replaced GB1160.2-89
Implemented on April 14, 1996
Marking example
JB/T 7941.2—1995
Viewing hole d=32, marking of A-type thorn-shaped round oil mark: oil mark A32GB1160.2
5 Technical conditions
Technical conditions are in accordance with the provisions of GB1163,
Additional instructions:
This standard is proposed by the Ministry of Machinery and Electronics Industry, JB/T7941.2—1995
This standard is under the jurisdiction of the Mechanical Standardization Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Science and Technology Information Institute of Shanghai Mechanical and Electrical Industry Administration Bureau and the Mechanical Standardization Institute of the Ministry of Machinery and Electronics Industry, and Shanghai Machine Tool Accessories Factory No. 6 and Shanghai Machine Tool Plastic Factory participated in the drafting. The main drafters of this standard are Chen Huajin and Zhang Jiade,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
JB/T7941.2—1995
Put-in round oil mark
Oil level indicators screwing round type1996-04-14Promulgated
Ministry of Machinery Industry of the People's Republic of China
Implementation on 1996-04-14
Mechanical Industry Standard of the People's Republic of China
Screw-in round oil mark
Oil level indicators screwing round typeSubject content and scope of application
This standard specifies the type and size of screw-in round oil marks. This standard is applicable to oil marks used to observe the oil level of lubricating oil on various mechanical equipment. 2 Reference standards
GB1163
3 Types and dimensions
Oil mark technical conditions
The sleeve mark is divided into two types: A and B: Type A see Figure 1. Type B see Figure 2. Dimensions see the table below Type A is used as an oil level indicator, and Type B is used to indicate the working condition of the oil. A
Approved by the Ministry of Machinery Industry on April 14, 1996
JB/T7941.2-1995Www.bzxZ.net
Replaced GB1160.2-89
Implemented on April 14, 1996
Marking example
JB/T 7941.2—1995
Viewing hole d=32, marking of A-type thorn-shaped round oil mark: oil mark A32GB1160.2
5 Technical conditions
Technical conditions are in accordance with the provisions of GB1163,
Additional instructions:
This standard is proposed by the Ministry of Machinery and Electronics Industry, JB/T7941.2—1995
This standard is under the jurisdiction of the Mechanical Standardization Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Science and Technology Information Institute of Shanghai Mechanical and Electrical Industry Administration Bureau and the Mechanical Standardization Institute of the Ministry of Machinery and Electronics Industry, and Shanghai Machine Tool Accessories Factory No. 6 and Shanghai Machine Tool Plastic Factory participated in the drafting. The main drafters of this standard are Chen Huajin and Zhang Jiade,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- SL 261-1998 Chinese lake name code SL 261-98
- GB 12757-1991 Life-saving and heat-insulating appliances
- GB/T 6159.1-2003 Micrographics--Vocabulary--Part 1:General terms
- GB/T 17143.5-1997 Information technology Open Systems Interconnection System management Part 5: Event reporting management function
- JB/T 7273.3-1994 Handwheel
- QB/T 2337-1997 Insole forming machine
- GB/T 8413-1996 CZY type marine self-priming centrifugal water pump
- GB/T 1.3-1997 Directives for the work of standardization--Unit 1: Drafting and presentation of standards--Part 3: Rules for drafting product standards
- GB/T 4324.15-1984 Chemical analysis of tungsten - Chlorophosphonazo I spectrophotometric method for determination of magnesium content
- GB 18452-2001 Safety requirements for crushing equipment
- GB/T 15015-1994 Terms and definitions of physical properties and quantities in the field of expansion alloys
- QB/T 2490-2000 Polyethylene (PE) extruded sheet
- YC/T 37.1-2002 Determination of physical properties of filter rods Part 1: Length electro-optical method
- GB/T 9074.10-1988 Cross recessed countersunk head screw and conical locking washer assemblies
- SJ 20056-1992 Semiconductor discrete device-Detail specification for silicon NPN low power switching transistor of Type 3DK103
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：[email protected]