GB/T 15005-1994 Technical requirements for magnetic temperature compensation alloys

GB/T 15005-1994 Technical Specifications for Magnetic Temperature Compensation Alloys GB/T15005-1994 Standard download decompression password: www.bzxz.net

National Standard of the People's Republic of China
Technical conditions for magnetic temperature compensation alloys
Magnetic cnmpensate alloys depending ontcmperature variation technical requirementsCB/T 15005--94
Replaces GBn20488
This standard applies to cold-rolled strips of magnetic temperature compensation alloys 1J30, 1J31, 1J32, 1J33 and 1J38 for magnetic shunt compensation. 1 Dimensions and shape
1.1 Dimensions
The dimensions and allowable deviations of the alloy strips shall conform to the relevant provisions of GB/T15001 General provisions for dimensions, shape, surface quality, test methods and inspection rules for soft alloys.
1.2 Shape
The shape of the alloy strip shall conform to the relevant provisions of GB/T15001. According to the requirements of the purchaser, the cold-rolled strip can be delivered in straight strips. 2 Technical requirements
2.1 Grade and chemical composition
The alloy grade and chemical composition shall comply with the provisions of Table 1. When the alloy magnetic properties comply with the provisions of Table 2, the chemical composition is allowed to deviate from the range specified in Table 1.
Chemical composition
Alloy grade
Not more than
29.5~30.5
30. 5 ~-31. 5
31.5~32.5
32. 8~-33. 8
0, 30~~0. 60 / 0. 30 ~ 0. 60 1. 00~2, 00
0.30~-0.60
37.5~~38.5
(5. 15~0. 30
12.5~13.5
2.2 Smelting method
The alloy is smelted in a vacuum induction furnace. Other smelting methods that meet the requirements of this standard may also be used, but this should be noted in the quality certificate.
2.3 Delivery status
The alloy strip is delivered without heat treatment.
2.4 Magnetic properties
The magnetic properties of the alloy sample shall comply with the provisions of Table 2. The magnetic properties of 1J30, 1J31 and 1J32 alloys are tested in the annealed state. The magnetic properties of 1J33 and 1J38 alloys are tested in the cold rolled state, and are also allowed to be tested in the annealed state. Approved by the State Administration of Industry and Information Technology on April 4, 1994 and implemented on May 1, 1994
Alloy grades
GB/T 15005-94www.bzxz.net
Magnetic induction intensity at different temperatures when the magnetic induction intensity is 8000A/m,B2Y
0. 40 - 0. 600. 20-~ 01, 45
0. 60 ~0. 850. 40--0. 65
0. 80 ~ 1. 100. 60~0. 95
0. 4~-0. 70
0.02-0.13
0. 15 ~0. 45
0. 40 -~0. 75
0. 25 ~~ 0. 420. 05 ~0. 240. 015 ~0. 122.5 Surface quality
Magnetic induction intensity Landing pad
TB se~Bae Basr-~Bert / Bat-Bane0.10~[. 40
The surface quality of the alloy strip shall comply with the relevant provisions of GB/T 15001. 3 Test methods
3.1 The test methods of the alloy shall be carried out in accordance with the relevant provisions of GB/T15001. 3.2 The temperature deviation of the alloy magnetic property test shall not be greater than ±2C. 4 Test rules
The test rules of the alloy shall be carried out in accordance with the provisions of GB/T 15001. 5 Packaging, marking and quality certificate
0. 16~ 0. 210. 035--. 15
0.22~-. 42
The packaging, marking and quality certificate of the alloy strip shall comply with YB/T 5242-93 "General Regulations for Packaging, Marking and Quality Certificates of Precision Alloys", the basic physical parameters of the alloy are shown in the following table. Alloy Grade, g/em Additional Notes: GB/T15005-94 Appendix A Basic Physical Parameters of Alloys (Reference) 1J30, 1J31, 1332, 1J33 This standard was proposed by the Information and Standards Research Institute of the Ministry of Metallurgical Industry, and was drafted by Dalian Steel Plant. This standard is marked with GB/T15005-9411338
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.