Rules for the inspection of transport packaging for export commodities—Plastic container

This standard specifies the inspection items, sampling, inspection methods and determination of inspection results for plastic containers for export commodity transport packaging. This standard applies to the inspection of plastic containers for export commodity transport packaging by sea, land and air. SN/T 0271-1993 Inspection Procedure for Plastic Containers for Export Commodity Transport PackagingSN/T0271-1993 Standard download decompression password: www.bzxz.net
This standard specifies the inspection items, sampling, inspection methods and determination of inspection results for plastic containers for export commodity transport packaging. This standard applies to the inspection of plastic containers for export commodity transport packaging by sea, land and air.

GB 2828 Batch-by-batch inspection counting sampling procedures and sampling tables (applicable to inspection of continuous batches)
GB 13508 Polyethylene blow-molded barrels
ZB A87 001.2 Inspection Procedure for Dangerous Goods Packaging for Export by Sea Performance Inspection

Industry Standard of the People's Republic of China on Import and Export Commodity Inspection SN/T0271-93
Export Commodity Transport Packaging
Inspection Procedure for Plastic Containers
Rules for the inspection of transport packagingfor export commodities-Plastic container1993-12-15Promulgated
Implementation on 1994-05-01
Promulgated by the State Import and Export Commodity Inspection Bureau of the People's Republic of China Industry Standard of the People's Republic of China on Import and Export Commodity Inspection Inspection Procedure for Transport Packaging of Export Commodities
Rules for the inspection of transport packagingfor export commodities-Plastic container1 Content and Scope of ApplicationPlastic containers
SN/T 0271-93
This international standard defines the inspection items, sample inspection methods and inspection results for plastic containers for transport packaging of export commodities. This standard is used for the inspection of plastic containers for export goods transported by sea, indoor and outdoor. 2 Reference standards GB2328 Counting test procedure (applicable to the inspection of continuous batches) GB13508 Plastic bottles ZBA870C1.2 Inspection procedures for export goods by sea Performance inspection 3 Sampling External inspection Refer to GB2828; Performance inspection Refer to 2DA37001.2 and GH13508. 3-2 Inspection batch Products with the same raw materials, the same structure and the same process are one inspection batch, and the quantity batch is 10 200 pieces. 3.3 Random sampling 3.3.1 The double-sided test data shall be as specified in Table 3.3.2 The double-sided test data shall be as specified in Table 1. If the number of qualified samples in the external test is less than the number required for performance control, sufficient samples may be randomly selected for inspection. Only the number of samples required for performance control shall be determined based on the number of samples. 3.3.3 Under the premise of not affecting the accuracy of the test tool, two tests are allowed for each sample. The Export Commodity Inspection Bureau of the People's Republic of China approved the following on 1993-12-15: the test of the type of material container for oral administration, safety of the type handle and the type 6 handle for oral administration, and the test of the type of material capacity of the type 6 handle for oral administration, and the test ... 0271-93
4.1.1 Inspection items: barrel, bubbles, black impurities, scratches, sticking (only for hollow handles); signs, seals, nominal capacity: 4.1.2 Inspection methods: according to the requirements of Table 2, 4.1.3 Inspection requirements. The technical requirements for appearance inspection shall comply with the requirements of Table 2. Table 2
Inspection items
Standard specifications
New specificationsbzxZ.net
4.2 Performance inspection
Technical requirements
The code specified by the manufacturer shall be used. The code shall be used for overlap. The second best
quantity is greater than the weighing
20 L 1. 1 u%, 25 1. 1.2 3un.3G J. 1. 5 mm. ; The seat part of the car is not big
, no year-old, no reflection-outer light, mouth, no bubbles on the seat edge, no bad selection is not more than 2mm. Add spacing is larger than 2mm, the length is not more than 4 rnm, no penetration, no hollow support. 5 with liquid
4.2.1 Performance inspection attack month connection table 1 observation, 4.2.2 Vertical and impact embedment test
method according to 28A87001.2 escape 4.2.2.1
joint classification
4.2-2.2 Drop height: use water belt prohibit substitutes, intended installation For products with a height of no more than 1.2, the drop height is 0.8m; for products with a width of more than 1.2, the drop height is 0.67×density. 4.2.2.3 Drop location,
Open single-material container, woven chain, bottom and joint or imported plastic container: one sample each for bottom closure, barrel bottom and joint of the whole cabinet. 4.2.3 Stacking test
4. 2. 3. 1
Test test, test 5 28A87001.2 send 4.2. 3.2
Stacking time is? d.
Stacking quantity is calculated as follows:
Stacking mass on the plastic container, hg: formula: w
M,——single piece of carbon mass, k1
H stacking height: 1.3m
Height of a single plastic container, m;
integer.
4.2.4 Airtightness test
SN/T 0271—93
4.2-.4.1 Test method: According to 2BA8001.2. 4.2.4.2 Test gas pressure: 20kPa.
4.2.5 Hydraulic test
4.2.5.1 Test method: According to 7.BA87 (00.1.2. 4.2.5.2 Test pressure: 100kPa.
4.2-6 Unloading test: According to GB 23508 reverse. 4.2.7 Lead test: According to GR13508 optional
5 Determination of inspection results
5.1 Appearance inspection: If there is one or three C in a sample barrel, the barrel is unqualified: the batch determination is according to 3. Table 3
151--500
5G1--1200
1201-32c0
3 2G1--13 009
Qualified judgment
Not including qualified judgment number
5.2 Vertical or impact fall correction test, the test details and no leaking, the contents of the no leaking or number of belts are qualified, as long as one of the details is unqualified, the full must be unqualified.
5.3 Push the test face sample does not fall, not full end is qualified: as long as one sample is unqualified, the item is unqualified. 5.≤ Gas case test; the sample is not qualified. If there is one sample unqualified, the item is unqualified, 5.5 Pressurized test: the sample is not leaking is qualified, as long as one sample is not qualified, the top is unqualified, 5.6 Sealing test, the test push is not qualified. As long as there is. If only the auxiliary is unqualified, the item is unqualified. 5.7 The installed handle does not fall off in the hanging test, and the carbon residual variation of the whole handle is not greater than 4. If 5-8 external inspection and performance inspection are qualified, the inspection batch is qualified. As long as there is one unqualified, the inspection batch is unqualified. Added Note:
This standard is proposed by the People's Republic of China after the export commodity inspection, and the standard is funded by the Jiangsu Export Commodity Inspection Bureau of the People's Republic of China and the Changzhou Import and Export Commodity Packaging Registration and Inspection Institute. This standard mainly follows the academicians, He Ziwei, Fang Daren, and Zhu Bosheng
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.