HG/T 21583-1995 Quick-opening stainless steel movable cover

HG/T 21583-1995 Quick-opening stainless steel movable cover HG/T21583-1995 standard download decompression password: www.bzxz.net

People's Republic of China Industry Standard
Quick open stainless steel movable cover
HG/T21583-95
Editor: Equipment and Technology Center of Ministry of Chemical Industry Approval department: Ministry of Industry and Information Technology of Beijing
Real date, September 1, 2011 Ministry of Chemical Industry Engineering Construction Standard Compilation Light Center
Theme Internal rate and station related specifications
Lighting standard
Type and size
Situation and Austrian practice
Main wing size quality
Two civil sizes in ...
4 Technical requirements..
Type pipe, fast aging insurance
Yunlan's
+1-1tt
Tight production
Unofficial request
4.B Youzu control stability
4. 0 installation
4.10 Uncompacted surface tightness test
Marking and marking mark engraving......
5.1 Marking
5.2 Marking examples
Drawing catalog
Abbreviation description
..............
Document of the Ministry of Chemical Industry
Chemical Construction Development No. 119951650
Notice on the promotion of five industry standards including "Plunger Type Discharge Valve"
All provinces, autonomous regions, municipalities directly under the Central Government, and cities with independent planning status Chemical Industry Departments (bureaus, companies), all relevant units shall organize the establishment of technical centers and markets of the Ministry of Pharmaceutical Industry to promote the promotion of five industry standards including "Plunger Type Discharge Valve" and "Plunger Type Discharge Valve". It has been in effect since January 1950. This standard is managed by the Ministry of Equipment Design and Technology Center, and the Ministry of Engineering Design Standard Compilation Center is responsible for publishing and issuing. Document: Ministry of Chemical Industry, August 38, 1995, 16-18510, Subject Content and Scope of Application. This standard specifies the type, basic parameters, dimensions, technical requirements and relevant regulations of quick-opening stainless steel movable covers (hereinafter referred to as quick-opening covers). This standard is used for quick-opening salt with a nominal pressure of PN0.25MPa (2.5kgf/em\>r. This quick-opening cover is not suitable for medium with a toxic hazard or above and a dry and explosive hazard. Note that the upper and lower limits of the quick-opening cover should be kept within the limits specified by the manufacturer. The material quality is only listed in Table 4. 8.4 Established.
GB-R31
CGB4237
CBE676
Referenced Standards
3 Steel Pressure Vessels3
Dense Standards
3Those with Standard Tolerances and Matchings3
Flow Smooth Low-Pressure Structural Steel Technical Requirements
Certification System Technical Properties
Classification of Steel Parts and Matchings without Notes on Standards Small Model Differences?
A Share of Workers Holding War Steel3
3 Chain parts 3
JR/4709
Steel positive force gear connection process?
JB4728
JB473C
Positive force storage device using human-induced steel silver parts 3
Card force capacity sign no basis for measurement
&Standardized chemical equipment scientific and technological development regulations
Type and size
3.1.1 Quick opening is divided into two types: rotating disk (A type) and horizontal product cover (B type). See Figure 3.1.1-1~2 and Table 3.1.1-1~2
See Figure 3.1.1-
Figure 3. 3. 1 - 2
GJ3 682—Be
GB1-86
.GB 97. 2- g6
CB89286
GB 97. 2 86
GB 91-25
Article section Kang except
Seek shape to the end
[Transfer
Note, the parts without note shall be abandoned by the designer. Table 3. 1- 1 -1
Q35--A
ZG830 45:
225—A
Q235-A
Q235-A
In this document, if the components are same, when the components are same, the requirements for making them should be changed to 304 stainless steel, similar to the customer's order (see Section 5.1).6
GR B39-75
GE5781-8
GB 97-1: 85www.bzxz.net
CB882--66
GB 97.1—85
GHA1-E
Back bolt
Kailan face
Spherical head
Hand probe
Weakened plate
my country plate
Rotary auxiliary seat
Table 3. 1. 1-2
Q235-A
Q235-A
20230-453
Q235—A
Q235-A
Q235—A
HT 200
Q235-A
The material sample of the parts with unqualified material grade shall be calculated by the design and placed by the user. When the user requires a grade higher than 20, it shall be changed to 304 quality
without restriction and shall not be indicated when ordering (must be specified in Section 1). 7
3. 2 Specifications and Types
The specifications and corresponding types of quick-open lids shall be in accordance with the provisions of 3-2-1. 3.2.1
Specifications and Types
3.3 Main Dimensions and Quality
The main dimensions and bases of quick-open lids shall be in accordance with the provisions of Table 3.3.1, Table
159×6
503×13
Table 3. 2. 1
Table 3. 3. 1
If the quick-open lid manufacturer changes the H, the change shall be allowed, but the height and size after the change shall be clearly indicated, and the front plate shall be changed.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.