JB/T 9005.9-1999 Casting pulley for crane F type

JB/T 9005.9-1999 JB/T 9005.9-1999 Casting pulley for crane F type JB/T9005.9-1999 Standard download decompression password: www.bzxz.net

JB/T 9005.9--- 1999
This standard adopts DIN15417:1982 "D-type wire rope pulley", DIN1850:1976 Part 1 "Bushing for wire rope pulley", IDIN15069:1977 "Isolator for wire rope pulley". This standard is a revision of ZB3J80006.9--87 "F-type cast pulley for crane". Only editorial changes were made to the original standard during the revision, and the main technical content did not change. This standard is part of the JB/T9005 series of standards "Cast pulleys for cranes", which includes the following 10 parts: JB/T 9005.1--1999
JB/T 9005.2--1999
JB/T 9005.3-1999
JB/T 9005.4--1999
JB/T 9005.5--1999
JB/T 9005.6-1999
JB/T 9005.7---1999
JB/T 9005.8:-1999
JB/T 9005.9- 1999
JB/T 9005.10—1999
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
This standard replaces ZBJ80006.9-87 from the date of implementation. Selection series and matching
type of rope groove section
, hub and bearing size
Technical conditions
This standard is proposed and assigned by the National Technical Committee for Standardization of Hoisting Machinery. The responsible drafting unit of this standard is Dalian Daqi Group Co., Ltd. The main drafters of this standard are Zhou Yu'an and Cui Zhenyuan. 447
1 Scope
Machinery Industry Standard of the People's Republic of China
Casting sheaves for cranes
Type F- Casting sheaves for cranesJB/T9005.9--1999
Replaces ZBJ80006.987
This standard applies to cast wire rope sheaves with sliding bearings (hereinafter referred to as sheaves) within the scope of the movable sheave block of the crane. Sheaves specified in this standard can also be used in other sheaves in wire rope transmission, such as fixed sheaves or other load-bearing parts except the movable sheave block.
2 Types and dimensions
2.1 The types and dimensions of type F sheaves are detailed in Figure 1 and Table 1. Marking example:
Wire rope diameter d = 25mm. Pulley diameter L) = 630mm and diameter D, = 90mm F-type pulley, marked as: Pulley F25X630-90 JB/T 9005.9-—1999B:/2
Approved by the State Machinery Industry Bureau on 1999-06-28 448
Figure 1 F-type
2000-01-01 implementation
JB/T9005.9
To facilitate the installation of the pulley, the axial clearance rate of each side should be specified in the connection structure to be at least 1mm.2 According to design requirements, B size is allowed to change. 2.2 The dimensions of the bushing (T) for F-type pulleys are detailed in Figure 2 and Table 2. Marking example:
Bushing (T) for F-type pulley with diameter D, = 90mm, marked as: JB/T 9005.9--1999
Bushing T90
Note: Lubrication grooves shall be opened as required.
Figure 2 Bushing (T)
JB/T9005.9--1999
Unit weight
2.3For the dimensions of the spacer ring (H) for F-type pulley, please refer to the provisions in Figure 3 and Table 3. Marking example: wwW.bzxz.Net
Diameter D,-90mm for F-type pulley spacer (H), marked as: S6
Spacer H90JB/T9005.9.-1999
Figure 3 Spacer (H)
Unit weight
JB/T9005.9—1999
Unit weight
Note: S, the larger size in the dimension, is used when multiple pulleys are installed in parallel on the pulley shaft. D
Unit weight wall
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.