JG/T 132-2000 Polyvinyl chloride (PVC) door and window fixings

This standard is formulated in accordance with the provisions of GB/T 1.3-1997 "Guidelines for Standardization Work Unit 1: Rules for Drafting and Presenting Standards Part 3: Regulations for Writing Product Standards". This standard specifies the definition, product, model, requirements, test methods, inspection rules, marking, packaging, transportation and storage of polyvinyl chloride (PVC) door and window fixings. This standard applies to polyvinyl chloride (PVC) door and window fixings. JG/T 132-2000 Polyvinyl chloride (PVC) door and window fixings JG/T132-2000 Standard download decompression password: www.bzxz.net

JG/T132--2000
3—1997 "Guide to Standardization Work
This standard is formulated in accordance with the provisions of GB/T1.3+
Product Standard Preparation Regulations". Introduction
Unit 1: Drafting and Expression Rules of Standards This standard is proposed by the Standardization and Quota Research Institute of the Ministry of Construction of the People's Republic of China. This standard is under the jurisdiction of the Technical Committee for Standardization of Building Products and Components of the Ministry of Construction. Part 3
The drafting units of this standard are: China Building Metal Structure Association, Baoding Demas Building Materials Co., Ltd., Dalian Shide Plastic Industry Co., Ltd., Shandong Luhong Plastic Window Machinery Group Co., Ltd., Xinxiang Hualong Window Co., Ltd. The main drafters of this standard are: Liu Xuqiong, Wang Cunji, Wang Ying, Cheng Fengjie, Jing Fengshang, Lu Zhengzhong. This standard is entrusted to the Plastic Doors and Windows Committee of the China Building Metal Structure Association for interpretation. 218
Construction Industry Standard of the People's Republic of China Polyvinyl chloride (PVC) Door and Window Fixings
Wedges or fixings of rigid polyvinyl chloride window and door Scope
JG/T132—2000
This standard specifies the definition, product model, requirements, test methods, inspection rules, marking, packaging, transportation and storage of polyvinyl chloride (PVC) door and window fixings (hereinafter referred to as fixings). This standard applies to polyvinyl chloride (PVC) door and window fixings. 2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. All parties using this standard should explore the possibility of using the latest versions of the following standards. GB5926-1986 Appearance quality test method for metal coatings and chemical treatment layers of light industrial products GB/T11253-1989 Cold-rolled thin steel plates and strips of carbon structural steel and low-alloy structural steel QB/T3826-1999 Corrosion resistance test method for metal coatings and chemical treatment layers of light industrial products Cloud neutral salt spray test (NSS) method
QB/T3832-1999 Evaluation of corrosion test results of metal coatings of light industrial products 3 Definitions
This standard adopts the following definitions.
Wedges or fixings
Accessories for fixing door and window frames to building openings (see Figures 1 and 2). Figure 1
Structural diagram of one-way fixing piece approved by the Ministry of Construction of the People’s Republic of China on September 30, 2000
Implementation from December 1, 2000
4 Product model
4.1 Model
4.1.1 Name code
Plastic door and window fixing piece SGP
4.1.2 Main parameter code
JG/T132—2000
Figure 2 Structural diagram of two-way fixing piece
The length and width codes of the fixing piece, the length is expressed in actual size (mm) × 10-1 value, and the width is expressed in actual size (mm) value. 4.1.3 Characteristic code
One-way fixing plate D
Two-way fixing plate SbzxZ.net
4.2 Marking
4.2.1 Marking method
Width code
Length code
Characteristic code
Name code
4.2.2 Marking example
Two-way fixing plate is 200mm long and 25mm wide.
Marked as: SGP·S20X25
5 Requirements
5.1 Material
The material of the fixing plate shall be not less than the mechanical properties of Q235 specified in GB/T11253. 5.2 Appearance
5.2.1 The surface shall be flat and shall not have cracks, burrs or mechanical damage. 220
Main parameter code
JG/T132--2000
5.2.2 The surface of the anti-corrosion coating should have a uniform gloss and should not have defects such as bubbles, water marks, and exposed bottom. 5.3 Specifications and dimensions
5.3.1 The thickness of the fixing plate should not be less than 1.5mm, and the width should not be less than 20mm. 5.3.2 The installation hole diameter of the fixing plate is 5mm. 5.3.3 The size tolerance of the fixing plate and the profile matching claw is a+.25mm. 5.4 Corrosion resistance
The coating should be treated and the corrosion resistance should reach 48h8 level. Test method
6.1 Appearance
Visually inspect the sample at a distance of 400~500mm under natural light. Inspect according to GB/T5926. 6.2 Specifications and dimensions
Measure with a vernier caliper with an accuracy of 0.02mm. 6.3 Performance
Test the anti-corrosion ability according to the test method in QB/T3826 and evaluate according to QB/T3832. 7 Inspection rules
Product inspection is divided into factory inspection and type inspection. Products can only leave the factory after passing the inspection and attaching a certificate of conformity. 7.1 Factory inspection
7.1.1 Product factory inspection is carried out within the validity period of the type inspection. Products can only leave the factory after passing the inspection and attaching a certificate of conformity. 7.1.2 Factory inspection is carried out according to GB/T2828. Sampling adopts the normal inspection single sampling plan. The inspection level is level I. The qualified quality level AQL value and inspection items are specified in Table 1. Table 1 Factory Inspection Table
7.2 Type Inspection
Inspection Items
Specifications and Dimensions
Standard Clauses
7.2.1 Type inspection shall be conducted in any of the following cases: a) Test and finalization of new products or old products for transfer to factory production; Unqualified Category
b) After formal production, when there are major changes in structure, materials, and processes that may affect product performance; c) During normal production, inspection shall be conducted once a year; d) When the product is discontinued for more than one year and then resumed; e) When the factory inspection results are significantly different from the last type inspection; f) When type inspection is required by the national quality supervision agency or the contract. AQL
7.2.2 Type inspection shall be conducted in accordance with GB/T2829. Sampling shall adopt the normal inspection one-time sampling plan, the discrimination level shall be level 1, and the unqualified quality level RQL value and inspection items shall be as specified in Table 2. 221
Inspection Items
Standard Clauses
8 Marking, Packaging, Transportation and Storage
8.1 Marking
8.1.1 The product should have a trademark or factory name mark. JG/T132—2000
Table 2 Type Inspection Table
Unqualified Category
8.1.2 The product packaging should be marked with the product name, model or mark, trademark, grade, quantity, quality, volume, factory date, and factory name. 8.2 Packaging
8.2.1 The product should be packed in plastic bags to avoid mutual friction. 8.2.2 The package should contain a product certificate signed by the inspector. 8.3 Transportation
The product should be protected from impact, extrusion, rain, and moisture during transportation. 8.4 Storage
The product should be stored in a warehouse without corrosive media, with good air circulation and a relative humidity of less than 85%. 222
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.