JB/T 4318.2-2002 Horizontal band sawing machine Part 2: Parameters

This section specifies the parameters of horizontal band sawing machines. This section applies to newly designed general-purpose horizontal band saws. JB/T 4318.2-2002 Horizontal band sawing machine Part 2: Parameters JB/T4318.2-2002 Standard download and decompression password: www.bzxz.net

ICS25.080.60
Machinery Industry Standard of the People's Republic of China
JB/T4318.2-2002
replaces JB/T4318.2— 1996
Horizontal band sawing machine
Part 2: Parameters
Horizontal band sawing machinePart2:Parameters
Released on 2002-07-16
2002-12 -01Implementation
Foreword issued by the State Economic and Trade Commission of the People's Republic of China
Normative reference documents
Parameters
Horizontal band sawing machine
Picture 1
Picture 2
Column horizontal band sawing machine
Horizontal band sawing machine parameters
JB/T4318.2—2002
++++++++.
Previous
JB/T4318 "Horizontal Band Sawing Machine" is divided into four parts: -Part 1: Series Type Spectrum: | |tt|| - Part 2: Parameters;
- Part 3: Accuracy inspection:
- Part 4: Technical conditions.
This part is Part 2 of JB/T4318.
This part replaces JB/T4318.2-1996 "Horizontal Band Saw Parameters". Compared with JB/T4318.2--1996, the main changes in this part are as follows JB/T4318.2 —2002
The maximum sawing diameter d cancels the 200mm specification and adds three specifications of 1300mm, 1600mm and 2000mm; -Adds the second main parameter of the maximum sawing width. This part is proposed by China Machinery Industry Federation. This part is under the jurisdiction of the National Metal Cutting Machine Tool Standardization Technical Committee. The unit responsible for drafting this section: Changsha Sawing Machine Research Institute. The main drafters of this section: Chen Tiejian and Xu Sun. The previous versions of the standards replaced by this part are: -JB4318-1986, JB/T4318.2-1996. III | Horizontal band saw machine. 2 Normative reference documents
JB/T4318.2-2002
The provisions in the following documents become the provisions of this part through the reference of this part of JB/T4318. For dated reference documents, all subsequent amendments (excluding corrigenda) or revisions do not apply to this section. However, parties to an agreement based on this section are encouraged to study whether the latest versions of these documents can be used. . For undated referenced documents, the latest version applies to this section. JB/T7963.2 Metal Cutting Band Saw Blades Part 2: Basic Dimensions and Tolerances 3 Parameters
The type of horizontal band saw machine is shown in Figure 1 and Figure 2. The machine tool parameters should comply with the provisions of Table 1. Figure 1
Horizontal band sawing machine
Maximum sawing diameter d
Maximum sawing width L
Minimum band saw blade width b
(in line with JB/ T7963.2)Www.bzxZ.net
>250
Table 1
Horizontal band sawing machine parameters|| tt||400
>320
>400
>500
37.5| |tt||630
>630
Picture 2
Column horizontal band sawing machine
Unit:
mm|| tt||800
>800
>1000
>1300| |tt||65.0
>1600
>2000
华人Republic
Mechanical Industry Standards
Horizontal Band Sawing Machine: Part 2: Parameters
JB/T4318.2—2002|| tt||*
Published and distributed by Machinery Industry Press
No. 22, Baifangzhuang Street, Beijing
Postal code: 100037
Format 890mm ×1240mm1/16?0.5 sheets·6,000 words, 1st edition, 1st printing, December 2002
Price: 12.00 yuan
ISBN: 15111·7049||tt ||Website: http://cmpbook.com Editorial Department Telephone: (010) 88379779 Direct Sales Center Telephone: (010) 88379693 Covers without anti-counterfeiting labels are pirated
Copyright exclusive
Infringement is prohibited Study
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.