GB/T 5376-1996 Method for checking the speedometer indication value of motorcycles and mopeds

This standard specifies the calibration method for the speed and mileage indication values ​​of motorcycle and moped speedometers. This standard applies to motorcycles and mopeds (except off-road vehicles and racing cars). ? GB/T 5376-1996 Calibration method for the speed and mileage indication values ​​of motorcycle and moped speedometers GB/T5376-1996 Standard download decompression password: www.bzxz.net

National Standard of the People's Republic of China
Calibration method of indication forodometer of motorcycles and mopeds
Calibration method of indication forodometer of motorcycles and mopeds 1 Subject content and scope of application
GB/T 5376-1996
Replaces GB4560-84
GB 5376-85
This standard specifies the calibration method of speed and mileage indication of speedometer of motorcycles and mopeds. This standard applies to motorcycles and mopeds (except off-road vehicles and racing cars). 2 Referenced standards
GB/T5378 General rules for road tests of motorcycles and mopeds 3 Test conditions
Shall comply with the corresponding provisions of GB/T5378
4 Test method
4.1 Verification method of speed indicator of speedometer 4.1.1 Set up a test section of 100m on the test road, and there should be enough auxiliary driving area before and after. 4.1.2 In the auxiliary driving area, make the speed indicator value stable at the specified speed, and pass through the test section at this speed, and measure the time required to pass through the test section. Drive back and forth once. 4.1.3 Based on the maximum speed of the test vehicle, select the test speed according to the integer multiple of 10, and increase it in sequence to the maximum speed. The speed measurement points should not be less than four points.
4.1.4 Calculate the actual speed according to formula (1).
Where: x
ti, t2 -
actual speed, km/h;
length of test section, m;
time to pass through the test section once, t= + t2, s; respectively are the one-way time to pass through the test section, s. 4.1.5 Calculate the correction rate of the speed indication value according to formula (2). C . x
Wherein: C—speed indication value correction rate;
actual vehicle speed, km/h;
speed indicated on the speedometer, km/h.
Approved by the State Administration of Technical Supervision on April 10, 1996 (1)
Implementation on November 1, 1996
GB/T 5376-1996
4.1.6 Draw the correction curve of the speed indication value (see the figure below). x, km/h
Note: Use 1 mm coordinate paper for drawing.
4.1.7 Record the test data and results in Table B1 of Appendix B (Supplement). 4.2 Verification method of mileage indication value of speedometer 80
U,km/h
4.2.1 The driver takes the test vehicle and slowly rolls the wheel three times in a straight line on a flat test road to measure its rolling distance. The measurement is carried out three times and the arithmetic mean is taken. The rolling radius of the wheel is calculated according to formula (3). s
Rolling radius of the wheel, m;bZxz.net
Average distance of a wheel rolling three times, m. 4.2.2 Calculate the correction rate of mileage indication value according to formula (4) and (5). a, When the speedometer is driven by the wheel:
Actual driving distance (km)
Distance indicated by the speedometer (km)
When the speedometer is driven by the transmission:
Actual driving distance (km)
Distance indicated by the speedometer (km)
Where: c.
Correction rate of mileage indication value;
Odometer shaft revolutions
Odometer constant, -
E-meter indication distance (km)
Odometer driving gear ratio,
Odometer shaft revolutions
E-meter driving shaft revolutions
2 yuanrk
1000 yuan
2 yuanrk
Drive shaft reduction ratio, i2
GB/T5376—1996
Odometer driving shaft revolutions
Driving wheel revolutions
Note: When the odometer is driven by the transmission, the odometer driving shaft revolutions are the transmission driving shaft revolutions. 4.2.3 The test data and results are recorded in Appendix B Table B2. 119
GB/T 5376-- 1996
Appendix A
Supplementary Notes
(Supplementary)
A1During the performance test, the correction of the speed indication value can generally be obtained by using the correction curve to obtain the corresponding actual vehicle speed, or by using the correction rate for calculation.
A2The correction rate of the mileage indication value can also be obtained according to the actual highway sign mileage according to formula (A1). c,
Where: c,——correction rate of mileage indication value; Sx——actual highway sign mileage, km;
s——mileage indicated by the speedometer, km.
·（Al）
A3When testing with instruments such as motorcycle testers or five-wheel testers, the specified vehicle speed and mileage are controlled by the instrument, and the speed indication value and mileage indication value of the speedometer are recorded at the same time, and their correction rates are calculated according to formulas (A2) and (A3) respectively. C
In the formula: C
correction rate of vehicle speed indication value;
vehicle speed indicated by the testing instrument, km/h;
vehicle speed indicated by the speedometer, km/h;
correction rate of mileage indication value;
-mileage indicated by the testing instrument, km;
-mileage indicated by the speedometer, km.
Appendix B
Speedometer indication value verification test record sheet (supplement)
Speedometer indication value verification test record sheet
Test vehicle model
Test location
Vehicle frame number
Empty vehicle mass
Front wheel air pressure
Side wheel air pressure
Driver
Test date
Road conditions
Testing device
Driver mass
Rear wheel air pressure
Speed ​​mile Odometer model
Tester
（A3）
Test order丨Driving direction
Odometer indication
Test vehicle model
Test location
Vehicle frame number
Unladen weight
Front wheel pressure
Side wheel pressure
Driver
Test order
Additional instructions:
Test area
Distance between
GB/T 5376—1996
Test speed
Time to pass the section
Total time
Actual speed
Table B2 Mileage indication value calibration test record table Test date
Road conditions
Testing device
Driver quality
Rear wheel air pressure
Speedometer model
Tester
Distance of wheel rolling three times
Measured value
This standard is proposed by China National Automotive Industry Corporation. This standard is under the jurisdiction of the National Automobile Standardization Technical Committee. This standard is drafted by Shanghai Motorcycle Research Institute. The drafter of this standard is Huang Lan.
Average value
Speed ​​indicator
Indication correction
Mileage indicator
Indication correction
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.