JB/T 6534-1992 Centrifugal sewage pump types and basic parameters

This standard specifies the types and basic parameters of centrifugal sewage pumps. This standard is applicable to pumps that transport sewage, feces or liquids containing solid suspended matter such as fiber, paper scraps, fruit, fish, etc. JB/T 6534-1992 Centrifugal Sewage Pump Types and Basic Parameters JB/T6534-1992 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T6534-92
Centrifugal Sewage Pump
Published on December 25, 1992
Type and Basic Parameters
Implemented on July 1, 1993
Published by the Ministry of Machinery and Electronics Industry of the People's Republic of China
Mechanical Industry Standard of the People's Republic of China
Centrifugal Sewage Pump
Type and Basic Parameters
1 Subject Content and Scope of Application
JB/T6534-92
Replaces JB2975-81
This standard specifies the type and basic parameters of centrifugal sewage pumps (hereinafter referred to as "pumps"). This standard applies to pumps that transport sewage, feces or liquids containing solid suspended matter such as fiber, paper scraps, fruit, fish, etc. 2 Reference standards
GB7021
Centrifugal ticket terminology
JB/T6535 Technical conditions for centrifugal sewage pumps 3 Terms
3.1 The terminology used in this standard shall be in accordance with the provisions of GB7021. 3.2 The special terms in this standard shall be in accordance with the provisions of JB/T6535. 4 Types and basic parameters
4.1 Structural type
Pumps are divided into two types: single-stage, horizontal or vertical. Pumps with a discharge port diameter less than or equal to 250mm are single-suction and axial suction; pumps with a discharge port diameter greater than 250mm should generally be double-suction. 4.1.1 Horizontal pumps should be discharged vertically upward, or change the discharge direction at 45° or 90°. 4.1.2 Horizontal pumps with a discharge port diameter less than or equal to 150mm should have two types: ordinary type and corrosion-attached type. 4.2 Basic parameters
4.2.1 The basic parameters of the pump are as specified in the table. The values ​​in the table are the performance values ​​at the specified points for clean water at room temperature. The efficiency values ​​in the table are the efficiencies of ordinary closed impellers. When the impeller is open, its efficiency percentage can be reduced by 5 according to the value specified in the table; when the impeller is a single-channel, its efficiency percentage can be reduced by 10 according to the value specified in the table. Table
Pump model
Approved by the Ministry of Machinery and Electronics Industry on December 25, 1992 Head H
Speed ​​n
Required cavitation
(NPSH),
Flow section
Minimum size
Pump discharge diameter
Pump suction diameter
Implemented on July 1, 1993
Pump model
100WGF
1 00WGL
100WDFbzxZ.net
100WDL
150WGF
150WGL
150WDF
150WDL
200·WGL
200WDL
250WGL
250WDL
350WGL
350WDL
JB/T 653492
Head H
Efficiency work
Required cavitation
(NPSH),
Flow section
Minimum size
Diameter of pump outlet
True diameter of pump suction port
80/100
100/150
150/200
200/250
250/3 00
350/400
Pump model
500WGL
500WDL
600WGL
600WDL
800WDL
1000WD
1000WDL
1200WG
1200WGL
4.2.2The working range of the pump is shown in the figure.
The impeller can be cut according to the range in the figure. JB/T6534-92
Head H
Efficiency work
Required cavitation
(NPSH),
Flow section
Minimum size
Pump discharge diameter
Pump suction diameter
500/600
600/800
800/900
1000/12GO
1200/1400
6534-92
/70008:.0009:000 00000002
00010000100080009
0001008009
00000002
0001008
001-08
.01682
.oS.0%
JB/T6534—92
4.2.3The performance inspection and deviation of the pump shall comply with the provisions of JB/T6535. 4.3 Model designation method
Indicates whether the pump is corrosion resistant (corrosion resistant pumps are indicated by F, non-corrosion resistant pumps are not indicated)
Structural type (vertical type is indicated by L, horizontal type is not indicated) Head (higher than or equal to 20m is high head, indicated by G, lower than 20m is low head, indicated by D)
High-center sewage system
Pump outlet diameter, mm
Example 1: Vertical centrifugal sewage pump with a pump outlet diameter of 100mm and a head of 28m: 100WGL Example 2 Corrosion resistant horizontal centrifugal sewage pump with a pump outlet diameter of 100mm and a head of 14m: 100WDF5
Direction of rotation
From the drive end, the pump rotation direction should be clockwise. Additional notes:
This standard is proposed and managed by Shenyang Pump Research Institute. This standard was drafted by Shijiazhuang Institute of Wastewater Pumps. The main drafter of this standard is Zhang Yaxi.
People's Republic of China
Mechanical Industry Standard
Centrifugal Sewage Pump Types and Basic Parameters
JB/T6534-92
Published by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry, Printed by the Mechanical Standardization Research Institute of the Ministry of Machinery and Electronics Industry, Postal Code 100081)
(P.O. Box 8144, Beijing
Copyright reserved, no reproduction
Format 880×12301/16 Printing Sheet 1/2 Number of Words 10.000 First Edition May 1993 First Printing May 1993 Printing 00,001-500 Price 1.60 Yuan
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.