HG/T 3114-1998 Polypropylene Haier Ring Packing

HG/T 3114-1998 Polypropylene Haier Ring Packing HG/T3114-1998 Standard download decompression password: www.bzxz.net

ICS71.120,85.140
Registration No. 1972—1998
Chemical Industry Standard of the People's Republic of China
HG/T 3114-1998
Polypropylene heilex packing
Polypropylene heilex packing1998--03-17Release
1998—10-01Implementation
Ministry of Chemical Industry of the People's Republic of China
Mum. Customer Standard Industry Information Free Download HG/T3114—1998
Polypropylene heilex is a new and efficient packing in the world today. It combines the advantages of saddle packing and ring packing, with high efficiency, large processing capacity, not easy to block, energy saving, high mechanical strength, good corrosion resistance, etc. The product has been widely used in various industrial production. At present, there is no industry standard for this product in my country. In order to promote the relevant mechanical performance tests of the product, this standard is issued for the first time in my country. This standard is issued by China Chemical Equipment Corporation. This standard is formulated by the National Non-metallic Chemical Equipment Corporation on the basis of the unified basis. It is very necessary to formulate this standard. This standard is issued for the first time in China. This standard is issued for the first time in China. This standard is issued by China Chemical Equipment Corporation. This standard is formulated by the National Non-metallic Chemical Equipment Corporation on the basis of the unified basis. This standard is very necessary. This standard is issued for the first time in China. This standard is issued by China Chemical Equipment Corporation. This standard is formulated by the National Non-metallic Chemical Equipment Corporation on the basis of the unified basis. It is very necessary to formulate this standard. This standard is issued for the first time in China. This standard is issued by China Chemical Equipment Corporation. This standard is formulated ... The customer's technical requirements of the standard are further improved and the implementation of this order is created
The drafting unit of this standard: Tongzhou City, Jiangsu Province The main drafter of this standard: Ge Hongjun
Basic conditions
1 Scope
Chemical industry standard of the People's Republic of China
Polypropylene heilex packing
Polypropylene heilex packing This standard specifies polypropylene heilex
This standard is applicable to heilex made of other polymer materials with low service temperature). Reference standards
The provisions contained in the following standards are generally valid. All standards will be revised to make GB12670—90
ZBG910C4—87
ZBG91005—87
3 Definitions
Polypropylene forest
Polypropylene fresh
Polypropylene catfish male
This standard adopts the following definitions.
3.1 Drop hammer impact strength
During the drop hammer impact test, the environment
3.2 Compression yield strength
Compre
sionvieldstres
During the compression test, the shape and size of the filler on the load-deformation curve.
The shape and main dimensions of the filler shall conform to
HG/T3114-1998
Testing rules and marking, packaging, transportation and storage requirements of DN76DN100 polypropylene Haier Ring packing (hereinafter referred to as packing) When this standard is published, the versions shown are all
The possibility of opening the reverse version.
The load value at the first point where the load does not increase when adding. mm
When the user has special requirements for the size of the packing, it can be determined by negotiation between the supply and demand parties. 4.2
Approved by the Ministry of Chemical Industry of the People's Republic of China on March 17, 199830
1.5±0.12
2.0±0.20
2.4±0.26
Implementation on October 1, 1998
W 5 Requirements
HG/T3114—1998
5.1 The raw materials of propylene resin shall meet the requirements of injection molding grade resin performance in GB12670. 5.2 The surface of the filler shall not have bubbles, impurities and coking fracture phenomena, the edge shall be smooth without burrs, and the hole shall be clear. 5.3 The size deviation of the filler shall meet the requirements of Table 1. 5.4 The mechanical properties of the filler shall meet the requirements of Table 2. 2
6 Test methods
6.1 Raw materials
HG/T3714-1998
Drop hammer impact method Coagulation
Compression strength
The performance of propylene resin is a must-check item and should be inspected or accepted according to the regulations of 5.1. Materials that do not meet the requirements shall not be used. 6:2 Appearance||tt| |Appearance quality is checked by visual inspection.
6.3 Dimensions
Dimensional deviations are measured by a vernier caliper with an accuracy of not less than 0.02mm. Each dimension of the filler shall not be less than two measuring points, and the arithmetic mean is taken.
6.4 Mechanical properties
The chain drop impact test is carried out according to the method specified in ZBG91004, and the force form of the sample is shown in Figure 2. The compression test is carried out according to the method specified in ZBG91005, and the force form of the sample is shown in Figure 2. Figure 2
Inspection rules
7.1 Inspection classification
Product inspection is divided into factory inspection and type inspection. 7.1.1 Factory inspection
Each batch of fillers must pass the inspection before it can be shipped. The items for strict factory inspection are 5 of this standard. 2.5.3 Items specified. 3
W.7.1.2 Type inspection
HG/T3114—1998
7.1.2.1 Type inspection should generally be carried out in any of the following circumstances: a) When the product is put into production;
b) After normal production, if there are major changes in the product structure, process, or material, which may affect the product performance; c) When the product is resumed after a long period of suspension; d) When there is a significant difference between the factory inspection result and the last type inspection result; e) When the national quality supervision agency proposes a type inspection requirement. 7.1.2.2 Product type inspection is carried out once a year, and the inspection items are all the items specified in Chapter 5 of this standard. 7.2 Sampling and judgment rules
7.2.1 Batching and sampling
The same specification of fillers produced in the same shift and under the same process conditions are regarded as a batch, and 50 samples are randomly selected from each batch of fillers. 7.2.2 Judgment rules
If any item does not meet the requirements, the same number of specimens in the 7.2, 2.1 compression strength and drop weight impact strength tests shall be taken from the same batch of products, and the performance shall be retested, and the retest results shall be taken as the final results. 7.2.2.2 In the appearance quality and outer size inspection, if they are unqualified, retest shall be carried out, and the retest results shall be taken as the final results. If the retest results are not met, the product name and manufacture shall be marked on the outer packaging. 8.2 The packing belt shall be made of carton or plastic woven. 8.3 Each packaging bag shall contain the product type
a) product name, specification and quantity:
b) product standard number;
c) product production date, inspection date
d) inspection results and inspector's seal.
8.4 Filling materials should not be transported in
8.5 Filling materials should be stored in a dry, non-
place. If the
rate still exceeds 5%, the same number of samples should be drawn from the same batch of products. If the
rate still exceeds 5%, the batch of products is considered unqualified. Name, address, specifications, quantity and "Do not press" and other signs. Good packaging
quality warehouse
can be negotiated by the supply and demand parties.
and pollutants mixed transportation, shall not be subjected to heavy pressure. W People's Republic of China
Chemical Industry Standard
Polypropylene Haier Ring Packing wwW.bzxz.Net
HG/T3114-1998
Editor China Chemical Equipment Corporation
Postal Code 100011
Printing Beijing University of Chemical Technology Printing
All rights reserved, no reproduction
01/16 Printing Sheet 0. 75 Words 10. 5 thousand words Format 880X1230
First edition in September 1998 First printing in September 1998 Printing 1-150
Original fee: 6 yuan
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.