HG 21530-1995 Hand hole for flat welding flange with neck.

HG 21530-1995 Hand hole for flat welding flange with neck. Attached picture HG21530-1995 Standard download decompression password: www.bzxz.net

Hand holes for necked flat welding flanges
HG21530-95
Subject content and scope of application
This standard specifies the types, basic parameters, dimensions, technical requirements and relevant use regulations for hand holes for necked flat welding flanges made of carbon steel and low alloy steel.
This standard applies to hand holes for necked flat welding flanges with nominal pressure PN1.0～1.6MPa and working temperature limited to the range specified in Table 3-2 according to material category.
Note: The working temperature in Table 3-2 is only applicable to the pressure-bearing parts of the handball, excluding gaskets. The working temperature of the gasket should be determined according to the corresponding gasket standard.
HGJ 46--91
HGJ 47--91
HGJ 48—91
HGJ 61-91
HGJ 62-91
HGJ 63—91www.bzxz.net
HGJ 69-91
HGJ 70—91
HG 7 1-91
HGJ 75-91
HG 21514--95
Referenced standards
"Raised face flat weld steel pipe flange with neck"
"Concave and convex face flat weld steel pipe flange""Slip weld steel pipe flange with neck with grooved face""Raised face steel flange cover"
"Concave and convex face steel flange cover"
"Steel flange cover with grooved face"
"Asbestos rubber sheet gasket for steel pipe flange""Flexible stone composite gasket for steel pipe flange""Polytetrafluoroethylene coated gasket for steel pipe flange""Fasteners for steel pipe flange"
"Types and technical conditions of manholes and handholes made of carbon steel and low alloy steel" 3 Types, basic parameters and dimensions
For the types, basic parameters and dimensions of hand holes, please refer to the following figure and the provisions of Table 3-1 to Table 3-3. RF type
MFM type
Standard number
HGJ 75-91
HGJ 75—91
HGJ 46-48—91
HGJ69--91
HGJ 70—91
HGJ. 71-- 91
HGJ 61-63-91
Nominal pressure
Flange cover
See dimension table
See dimension table
Category code
20 (steel pipe)
20 (forging)
Asbestos rubber sheet gasket
Flexible graphite composite gasket
PTFE wrapped gasket
Q235-A
Q235-AF
Maximum non-shock working pressure at working temperature Table working
Maximum non-shock working pressure
Note: The maximum non-shock working pressure at intermediate temperature can be determined by interpolation according to the pressure value in this table. Ruler
(RF type)
(MFM type)
(TG type)
159×6
273×8
273×8
159×6
273×8
(150)159×6
(250)273×8||t t||39535026
405355
285240
395350
285240
405355
285240
40535526
n (forging)
Table 3-3
Diameter×length
M20X105
M20X110
M20X105
M24X120
M20x105
M20X110
M20×105
M24X115
M20X105
Total mass
M24X12052.5
Note: ① The height H1 of the hand hole is determined based on the diameter of the container being not less than twice the nominal diameter of the hand hole. If there are special requirements, changes are allowed, but the changed H1 size must be indicated and the total mass of the hand hole must be corrected. ② The nominal diameters in brackets in the table should not be used as much as possible. 148
Technical requirements
The technical requirements for hand holes shall comply with the provisions of Chapter 4 "Technical Conditions" in HG21514. 149
5: Marking example
The hand hole of a flat-welded flange with a nominal pressure of PN1.0, a nominal diameter of DN250, Hi-190, an RF sealing surface, and straight materials, and the gasket is an asbestos rubber sheet, and the specified marking symbol is: Hand hole RF (A·G) 250-1.0HG21530-9 For the above hand hole with 5H=220 (non-standard push size), the specified marking symbol is: Hand hole RFI (A·G) 250-1.0H-220HG21530-95150
Additional instructions
Proposer, editor-in-chief
and main drafter of this standard
Proposer: Equipment Design Technology Center Station of Ministry of Chemical Industry Editor-in-chief: Li Wenren of China Tianchen Chemical Engineering Company
Main drafter: Zhao Chenghe
Shen Pengfei
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.