GB/T 2914-1999 Determination of volatile matter (including water) of homopolymer and copolymer resins of plastics vinyl chloride

This standard specifies the method for determining the volatile matter (including water) in vinyl chloride homopolymer and copolymer resins. GB/T 2914-1999 Determination of volatile matter (including water) in plastic vinyl chloride homopolymer and copolymer resins GB/T2914-1999 Standard download decompression password: www.bzxz.net

1CS83.080.20
National Standard of the People's Republic of China
GB/T 2914—1999
idt ISO 1269:1980
Plastics--Homopolymer and copolymer resinsof vinyl chlorlde-Determlnation of volatilematter (including water) This standard is equivalent to the international standard IS01269:1980 Determination of volatile matter (including water) of ethylene glycol homopolymer and copolymer resins. The original standard GB/T2924-1982 did not indicate the adopted standard and the degree of adoption. This standard is a revised version of GB/T2914-19992 Determination of volatile matter (including water) of ethylene glycol homopolymer and copolymer resins. Compared with the previous version, the following differences are made: (1) Changes to the standard name. |tt||(2) This standard uses 8×3ml glass aluminum or stainless steel sample bottles, and the previous version uses glass 0mm×35m sample bottles.
(3) The format is written in accordance with the requirements of GB/T1.11993. This standard replaces GB/T2914-1982 from the date of implementation. This standard was proposed by the former Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the Technical Committee for Standardization of Plastics (TC15/SC7). The drafting units of this standard are: Xinsi Chemical Research Institute, Shanghai Chlor-Alkali Chemical Co., Ltd., and Shenyang Chemical Co., Ltd. The main drafters of this standard are Du Fengmei, Lao Huiquan, Zheng Ce, Bo Guarong, and Yan Zhou. This standard was drafted on March 2, 2012 First published, GB/T2914—1999
ISO Foreword
ISO (International Organization for Standardization) is a joint organization of various standards associations (ISOs) to formulate international standards. The work of formulating international standards is carried out by ISO technical committees. Any member organization that has established a technical committee has the right to send representatives to participate in the technical committee: governments or non-governmental organizations can also participate in this work after contacting ISO. The technical committee submits the draft international standard, which is voted by the member bodies before being approved as an international standard by the 5) Council. International Standard 1501269 was prepared by the 150/rC:61 Technical Committee: The second version was directly proposed by the International Standards Committee, according to Part 1, etc. 5.10.1 to guide the formulation of international standards. Technical work. Cancels and replaces the first edition 1501269:1975] The following member bodies are included: Austria
(former) Czech Republic
South Africa
South Africa
New Zealand
The following national bodies are formed by small technical original four heat show support to Romania
Bulgaria bzxz.net
Australia
Belgium
Israel
Yugoslavia
1 Scope
National Standard of the People's Republic of China
Plastics Vinyl Chloride Homopolymer and Copolymer Resins
Volatile Matter (including Water)
Plastics-Honepelymer nd copolymer reslusoP vinyl chlorideDeterminilom of roautilematter (iacludiag water)
This standard specifies the method for determining the homolysis and co-dispersion of ethylene in fertilizer (including water). 2 Principle
GBT 2914—1999
1dtIS01269.198
Agency CB/T2914152
Spread the test material in a weighing bottle of specified size and heat it at 110±2℃ until the mass is constant. 3 Apparatus
3.1 Chamber: It can be controlled at 110±2℃ and has a weak self-ignition ventilation. 3.2 Weighing bottle: It is about 30mmx30mm and is made of glass, aluminum or stainless steel with a lid. 3.3 Use a balance with a minimum graduation value of 0.0301: 3.4 Use a suitable desiccant. 4.1 Place a clean weighing bottle in a 110°C oven and heat for 1 hour. Take it out and cool it in a desiccator until solid. Then weigh it as accurately as possible to 0.3006g. 4.2 Place about 3g of the resin on the bottom of the weighing bottle, cover it, and weigh it to 0.005g. 4.3 Place the weighing bottle with the resin in a 110°C oven, remove the cover and place it in the oven. Close the door and start timing. Take it out after 1 hour, put it in a desiccator to cool to room temperature, weigh it accurately to 0.005g, and then heat it for 0.5h. Perform the same method as above and keep it constant until the difference between the two consecutive measurements is no more than 0.000g (it must be covered during the transfer and weighing process). The mass of the residue is calculated from this. Note: In special cases, the test temperature can be set at 105°C:=2°C, and 4.4 is measured twice under the same conditions. If the absolute value of the mass percentage measured in these two times differs by less than 0.10, they are calculated separately. Otherwise, the measurement is repeated until this requirement is met: If each of the two values ​​of the mass percentage measured is less than 0.30, no matter how much they differ, there is no need to re-determine.
5 Results
For each test, the following formula is used to calculate the mass percentage of the selected material (including the resin): 1×100
National Quality and Technical Supervision Bureau 19990916 batch oil (1)
2000-06-07 implementation
In the formula, m:
the mass before heating, 8F
the mass of the resin after heating.
C/T2914—1999
The average value of the two measured values ​​is reported as the result, rounded to two decimal places. Note
1 According to the requirements, for example, for a certain resin, one decimal place can be retained in the result. For the re-test of two different test items, the total measurement value is D. 1%. 6 Test report
Should include the following contents:
) Explanation of the use of this standard:
b) Completeness mark of the test product!
c) If the test is carried out at 105℃, the reason must be stated:
d) Report Chapter 5 Expression of results
e) Any conditions that may affect the test results.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.