QB 1798-1993 Lai Pai Tang Extract

This standard specifies the technical requirements, test methods and inspection rules of lycopodiella extract. This standard is applicable to lycopodiella extract obtained by extracting the branches and leaves of Cistus officinalis with organic solvents under heating. QB 1798-1993 lycopodiella extract QB1798-1993 Standard download decompression password: www.bzxz.net

Industry Standard of the People's Republic of China
QB1769~-1801-93Www.bzxZ.net
Standard for Spice
(Product Standard)
Published on April 29, 1993
Implemented on December 1, 1993
Published by the Ministry of Light Industry of the People's Republic of China
Subject Content and Applicable Scope
Industry Standard of the People's Republic of China KAoNTKAca=Q9 179B-93
Pay Attention
This standard specifies the technical requirements: test method, scientific control cavity, etc. This standard is applicable to the quick transfer of organic matter under the condition of technical connection and number of joints. 2 Reference standards GR/T111.8 Test method for negative color paste 3 Technical requirements 3.1 Color Green to brown color product. 3.2 Aroma The aroma of the paste is similar to that of the medicinal product. 5.3 Solubility (25℃) The value of the product is 1:1. The color of the product is green to brown. 3.4 Value = 80 3.5 Cooling factor 1, 4 Test method 4.1 Verification of negative color Place the sample on a white paper and the color should be green to yellow. 4.2 Determination of aroma ratio GB/T 14458 43 Determination of aroma degree, 25 °C 4.3.1 Apparatus, 13g biobalance, b. 100ml, e. Water soluble in warm water, d. 4.3.2 Reagents Chemically pure ester of 1,100ml ester, 4.3.3 Procedure Weigh the sample in a beaker, add 10% diethyl ketone, heat in water until the metal is dissolved. After heating at 11 °C, add 10% diethyl ketone, heat in water until the metal is dissolved. After heating at 11 °C, add 10% diethyl ketone, heat in water until the metal is dissolved. 4.4 Determination of acidity GB/T 118.
The Ministry of Light Industry of the People's Republic of China approved the implementation of the 1983-[2-01] G429 in 1993-1
Q81798-93
The color of this product is relatively clear: the agreed end point is unknown, and it can be titrated with a pH meter at pH-9. 4.5 The color of the wood product is relatively clear, and the agreed end point is not obvious. It can be titrated with a pH meter at pH-9. 5 According to the inspection rules
5.1 When the finished product is ready, the manufacturer will be responsible for the qualification of the product. The manufacturer (car manufacturer) shall ensure that the product meets the requirements of this standard. The basic batch of products shipped from the factory shall be accompanied by a certificate of qualification, manufacturer, product preparation, trademark, production date (batch number), net currency, and product quality certification number. 5.2 The unit has the right to accept the provisions of the standard and inspect the products. The quality of the products is determined by the requirements of this standard. Each batch shall be inspected once, and different batches shall be inspected separately. 5.3 For each batch with less than 100 pieces, two samples shall be selected for testing, and one sample shall be selected for more than 13 pieces. When sampling, the samples shall be placed in the upper and lower parts or in the middle of 3 pieces of water, and the sample shall be drawn with glass. The total number of samples shall not be less than 23%, and the mixed samples shall be mixed evenly. The samples shall be placed in two clean glass bottles respectively, and the following shall be noted: product name, manufacturer name, batch number, teaching, date and sampler. One bottle shall be used for inspection, and the other bottle shall be kept for inspection. 5.4 If any indicator of the acceptance result does not meet the requirements of this standard, the product shall be re-tested. If any indicator of the re-test result is unqualified, the product shall not be accepted. 5.5 When the supplier has any problems with the product quality, the two parties can negotiate and decide or submit it to the statutory testing agency, and the supplier shall be responsible for the cost.
B Marking, packaging, transportation, storage
6.1 The mold material used for the aluminum mold shall be packaged with the following information: manufacturer, product name, model, batch number, inspection year, [) "expiration date and technical number. 6.2 The temperature of the product in the flow and ventilation place shall not exceed 1000℃. The transportation must be strictly in accordance with the design limit and shall not be mixed with corrosive and strong gas items. Negative gas live, 6.3 abandoned in accordance with the provisions of the subject slaughter cattle, complete, complete, under the condition of the request, the shelf life of this product is two years, additional instructions:
This standard is from the Ministry of Light Industry, the Ministry of Standards, ...
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.