JB/T 9005.3-1999 Types, hubs and bearing dimensions of cast pulleys for cranes

JB/T 9005.3-1999 JB/T 9005.3-1999 Types, hubs and bearing dimensions of cast pulleys for cranes JB/T9005.3-1999 Standard download decompression password: www.bzxz.net

JB/T9005.3-1999
This standard adopts DIN15062:1982 Part 2 "Dimensions of crane wire rope pulley hub and support". This standard is a revision of ZBJ80006.3-87 "Types, hubs and bearing dimensions of cast pulleys for cranes". During the revision, only editorial changes were made to the original standard, and the main technical content remained unchanged. This standard is part of the JB/T9005 series of standards "Cast pulleys for cranes", which includes the following 10 parts: JB/T 9005.1-1999
JB/T 9005. 2—1999
JB/T 9005.3—1999
JB/T 9005. 4—1999
JB/T 9005. 5--1999
JB/T 9005.6—1999
JB/T 9005. 7-1999
JB/T 9005. 8-1999
JB/T 9005. 9—1999
JB/T 9005.10--1999
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Cast pulley for crane
Rope groove section
Diameter selection series and matching
Type, hub and bearing sizebzxZ.net
Cast pulley for crane
Cast pulley for crane
Technical conditions
This standard replaces ZBJ80006.3-87 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Hoisting Machinery. The responsible drafting unit of this standard: Dalian Daqi Group Co., Ltd. The main drafters of this standard: Zhou Yu'an and Cui Zhenyuan. 403
Machinery Industry Standard of the People's Republic of China
Casting sheaves for cranes--Type, dimensions of hubs and bearings1 Scope
This standard specifies the structural type, hub and bearing dimensions of casting sheaves for cranes. JB/T9005.3-1999
Replaces ZB J80 006.3--87
This standard is mainly applicable to cast wire rope sheaves for bridge cranes and gantry cranes (hereinafter referred to as sheaves). Sheaves for other cranes can also be used for reference.
The sheaves referred to in this standard include the balancing sheaves in the wire rope transmission of cranes. 2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are all valid. All standards will be revised. All parties using this standard should explore the possibility of using the latest version of the following standards. JB/T9005.4--1999 Type A cast pulley for crane JB/T9005.5-1999 Type B cast pulley for crane
JB/T9005.6-1999 Type C cast pulley for crane JB/T9005.7---1999 Type D cast pulley for crane
JB/T9005.8-1999 Type F cast pulley for crane 3 types
3.1 The types of pulleys are divided into the following 6 types according to their structure and use requirements: Type A---Pulley with rolling bearing (tight seal) and inner sleeve, as shown in Figure 1. Its structural dimensions are shown in JB/T9005.4. Type B - Pulley with rolling bearing (tight seal) and without inner sleeve, as shown in Figure 2. Its structural dimensions are shown in JB/T9005.5. Type C -
Pulley with rolling bearing (tighter seal) and inner sleeve, as shown in Figure 3. Its structural dimensions are shown in JB/T9005.6. Pulley with rolling bearing (tighter seal) and without inner sleeve, as shown in Figure 4. Its structural dimensions are shown in JB/T9005.7. Pulley with rolling bearing (general seal) and without inner sleeve, as shown in Figure 5. Its structural dimensions are shown in JB/T9005.8. Pulley with sliding bearing, as shown in Figure 6. Its structural dimensions are shown in JB/T9005.9. Type F
3.2 Method of indicating pulley
Approved by the State Bureau of Machinery Industry on June 28, 1999 404
Implemented on January 1, 2000
JB/T9005.3-1999
Pulley model dXD-DJB/T9005.3
Standard number
Diameter of pulley shaft, mm
Diameter of wire rope and pulley, mm||tt ||Represented by A, B, C, D, E, F respectively
3.3 Marking example
A type pulley with wire rope diameter d=25mm, pulley diameter D=630mm and pulley shaft diameter D=90mm is marked as: pulley A25X630-90JB/T9005.3--19994 Hub and bearing dimensions
For the hub and bearing dimensions of A type to F type pulleys, please refer to Figures 1 to 7 and Tables 1 to 5. 4-
Figure A type
Note: B—2B;-5.
JB/T9005.3--1999
Figure 2 Type B
E-B3-5
Figure 3 Type
JB/T9005.3-1999
Figure 4 Type D
Figure 5 Type E
JB/T 9005.3--1999
Figure 6 Type F
Note: For B: dimensions of A-D and F pulleys, the clearance is not given. However, in order to enable installation, the axial clearance on each side in the connection structure is specified to be at least 1 mm.
Type A, B
Type C, D
JB/T9005.3-
JB/T9005.3—1999
-5-6-8-4
3—4—
JB/T9005.3.-1999
Table 3 Bearing dimensions
Rolling bearing code
JB/T 9005.3--1999
Hub dimensions
Reference scale
JB/T9005.3--1999
Table 5 Hub dimensions
Basic dimensions
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.