消防水带卷盘

STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

Australian/New Zealand Standard

Fire hose reels

SECTION 1 SCOPE AND GENERAL

1.1 SCOPE

This Standard specifies requirements for design, construction and performance of fixed and swing arm type fire hose reels intended for use by one operator.

It does not include requirements for location or maintenance of fire hose reels since these subjects are covered in other Standards.

NOTES:

1. Methods for demonstrating compliance with this Standard are given in Appendix ‘A’.
2. A fire hose reel is generally referred to in this document as a hose reel’ or ‘the hose reel’.

1.2 NEW DESIGNS AND INNOVATIONS

Any alternative materials, designs, methods of assembly, procedures and the like that do not comply with specific requirements of this Standard or are not mentioned in it, but that give equivalent results to those specified are not necessarily prohibited, but the specified approval remains the prerogative of the regulatory authority.

1.3 REFERENCED DOCUMENTS

The following documents are referred to in this Standard:

6

AS/NZS 1221:1977

This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee FP-007, Fire Hose Reels. It was approved on behalf of the Council of Standards Australia on 5 September 1997 and on behalf of the Council of Standards New Zealand on 19 September 1997. It was published on 5 November 1997.

The following are represented on Committee FP-007:

• Association of Hydraulic Services Consultants Australia
• Australasian Fire Authorities Council
• Australian Association of Certification Bodies
• Australian Building Codes Board
• Australian Chamber of Commerce and Industry
• Fire Protection Association Australia
• Fire Protection Association New Zealand
• New Zealand Fire Equipment Association
• Plastics and Chemicals Industries Association Incorporated
• Sydney Water Corporation
• Telstra Corporation Limited

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased.

Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Australia web site at www.standards.com.au or Standards New Zealand web site at www.standards.co.nz and looking up the relevant Standard in the on-line catalogue.

Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a number of update options. For information about these services, users should contact their respective national Standards organization.

We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Please address your comments to the Chief Executive of either Standards Australia International or Standards New Zealand at the address shown on the back cover.

This Standard was issued in draft form for comment as DR 95364..

2

Australian/New Zealand Standard™

Fire hose reels

Originated in Australia as AS A155—1966.

Final Australian edition AS 1221—1991.

Originated in New Zealand as NZSS 1168—1954 and NZSS 2049—1966.

Final New Zealand edition NZS 4504:1981.

AS 1221—1991 and NZS 4504:1981 jointly revised, amalgamated and designated AS/NZS 1221:1997.

Reissued incorporating Amendment No. 1 (January 2003).

COPYRIGHT

© Standards Australia/Standards New Zealand

All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.

Jointly published by Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001 and Standards New Zealand, Private Bag 2439, Wellington 6020

ISBN 0 7337 1496 X

3

PREFACE

This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee FP-007 on Fire Hose Reels. This Standard supersedes AS 1221—1991 Fire hose reels and NZS 4504—1981 Specifications for fire hose reels.

This Standard incorporates Amendment 1 (January 2003). The changes required by the Amendment are indicated in the text by a marginal bar and amendment number against the clause, note, table, figure, or part thereof affected.

The objective of this Standard is to provide specific requirements for fire hose reels to meet the requirements of the appropriate regulatory authority when used in Australia and New Zealand.

It provides requirements for design, construction and performance of fixed and swing type fire hose reels.

It does not include location, installation or maintenance of fire hose reels since these subjects are covered in other Standards.

Hose reels used in Australia are usually fitted with 19 mm nominal diameter hose and those used in New Zealand are usually fitted with 13 mm nominal diameter hose. In cases where the ability to operate at lower inlet pressures or higher flow rates is desirable, a hose reel fitted with a 25 mm nominal diameter hose may be necessary. Hose reels fitted with 25 mm nominal diameter hose are required by some regulatory authorities.

The terms ‘normative’ and ‘informative’ have been used in this Standard to define the application of the appendix to which they apply. A ‘normative’ appendix is an integral part of a Standard, whereas an ‘informative’ appendix is only for information and guidance.

4

CONTENTS

5

STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

Australian/New Zealand Standard

Fire hose reels

SECTION 1 SCOPE AND GENERAL

1.1 SCOPE

This Standard specifies requirements for design, construction and performance of fixed and swing arm type fire hose reels intended for use by one operator.

It does not include requirements for location or maintenance of fire hose reels since these subjects are covered in other Standards.

NOTES:

1. Methods for demonstrating compliance with this Standard are given in Appendix ‘A’.
2. A fire hose reel is generally referred to in this document as a hose reel’ or ‘the hose reel’.

1.2 NEW DESIGNS AND INNOVATIONS

Any alternative materials, designs, methods of assembly, procedures and the like that do not comply with specific requirements of this Standard or are not mentioned in it, but that give equivalent results to those specified are not necessarily prohibited, but the specified approval remains the prerogative of the regulatory authority.

1.3 REFERENCED DOCUMENTS

The following documents are referred to in this Standard:

6