HG/T 2257-1991 Determination of volatility of photographic chemicals
time:
2024-08-13 09:29:54
- HG/T 2257-1991
- in force
Standard ID:
HG/T 2257-1991
Standard Name:
Determination of volatility of photographic chemicals
Chinese Name:
照相化学品 成色剂挥发性的测定
Standard category:
Chemical industry standards (HG)
-
Date of Release:
1991-12-28 -
Date of Implementation:
1992-07-01
Standard ICS number:
Imaging technology>>Photographic technology>>37.040.30 Pharmaceuticals for photographyChina Standard Classification Number:
Chemicals>>Information Chemicals>>G81 Photosensitive Materials
Skip to download
Summary:
HG/T 2257-1991 Determination of volatility of colorants in photographic chemicals HG/T2257-1991 Standard download decompression password: www.bzxz.net
Some standard content:
Chemical Industry Standard of the People's Republic of China
Photographic Chemicals
Determination of Volatile Matter of Color Forming Agents
1 Subject Content and Scope of ApplicationWww.bzxZ.net
This standard specifies the method for determining the volatile matter of color forming agents by the oven method. This standard is applicable to color forming agents used in the production of color films, color films and color photographic papers. 2 Method Summary
At a specified temperature, allow volatile substances in a sample of known mass to escape until constant weight is achieved. 3 Instruments or Equipment
3.1 Oven: accuracy of ±2°C,
3.2 Weighing bottle: diameter 55mm, height 35mm or diameter 80mm, height 30mm, 3.3 Balance: sensitivity 0.1mg
3.4 Desiccator: filled with color-changing silica gel or anhydrous calcium chloride. 4 Determination method
HG2257-91
Weigh 1g of sample in a constant-weight weighing bottle, accurate to 0.1mg. Put it in an oven and dry it at a specified temperature to constant weight (about 4h). The measurement temperature is generally 105℃. For low-melting-point colorants, the measurement temperature should be 20℃ lower than its melting point. Calculation of measurement results
The mass percentage X of volatile matter is calculated as follows: X
Where: m——the mass of the weighing bottle plus the sample before drying, g; m2—the mass of the weighing bottle plus the sample after drying, g; the mass of the weighing bottle, g.
Measure three times in parallel, the range should not be greater than ±0.04%, and the result is averaged. Approved by the Ministry of Chemical Industry of the People's Republic of China on December 28, 199112
Standard Technology Exchange Network m.baosp:coAll kinds of standard industry information free download 1992-07-01 implementation
Additional remarks:
HG 2257
This standard is proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China, and is managed by the Photographic Chemicals Standardization Technical Management Unit of the Ministry of Chemical Industry. This standard is drafted by Qingdao Dye Factory, and the Photosensitive Materials Technology Development Center of the Ministry of Chemical Industry participated in the drafting. The main drafters of this standard are Hu Jialin, Zhuang Youqin, Wen Huiqiong, and Hu Suqin. Standard Acquisition Network mm.bzeosg.cn13
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Photographic Chemicals
Determination of Volatile Matter of Color Forming Agents
1 Subject Content and Scope of ApplicationWww.bzxZ.net
This standard specifies the method for determining the volatile matter of color forming agents by the oven method. This standard is applicable to color forming agents used in the production of color films, color films and color photographic papers. 2 Method Summary
At a specified temperature, allow volatile substances in a sample of known mass to escape until constant weight is achieved. 3 Instruments or Equipment
3.1 Oven: accuracy of ±2°C,
3.2 Weighing bottle: diameter 55mm, height 35mm or diameter 80mm, height 30mm, 3.3 Balance: sensitivity 0.1mg
3.4 Desiccator: filled with color-changing silica gel or anhydrous calcium chloride. 4 Determination method
HG2257-91
Weigh 1g of sample in a constant-weight weighing bottle, accurate to 0.1mg. Put it in an oven and dry it at a specified temperature to constant weight (about 4h). The measurement temperature is generally 105℃. For low-melting-point colorants, the measurement temperature should be 20℃ lower than its melting point. Calculation of measurement results
The mass percentage X of volatile matter is calculated as follows: X
Where: m——the mass of the weighing bottle plus the sample before drying, g; m2—the mass of the weighing bottle plus the sample after drying, g; the mass of the weighing bottle, g.
Measure three times in parallel, the range should not be greater than ±0.04%, and the result is averaged. Approved by the Ministry of Chemical Industry of the People's Republic of China on December 28, 199112
Standard Technology Exchange Network m.baosp:coAll kinds of standard industry information free download 1992-07-01 implementation
Additional remarks:
HG 2257
This standard is proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China, and is managed by the Photographic Chemicals Standardization Technical Management Unit of the Ministry of Chemical Industry. This standard is drafted by Qingdao Dye Factory, and the Photosensitive Materials Technology Development Center of the Ministry of Chemical Industry participated in the drafting. The main drafters of this standard are Hu Jialin, Zhuang Youqin, Wen Huiqiong, and Hu Suqin. Standard Acquisition Network mm.bzeosg.cn13
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB/T 4798.10-1991 Introduction to environmental conditions for application of electrical and electronic products
- HG/T 3573-1990 Photographic grade sodium chloride (for emulsion)
- JB/T 6010-1992 Internal combustion engine oil pump gear series parameters
- SY 4024-1993 General Rules for Quality Inspection and Assessment of Petroleum Construction Projects
- GB/T 4678.16-2003 Die casting parts Part 16: Flat push rods
- JB/T 8330.1-1996 CNC profile fixed beam gantry boring and milling machine accuracy
- JB/T 3411.97-1999 Dimensions of end milling cutter bars for boring machines
- JGJ 83-1991 Specification for engineering geological investigation in soft soil areas
- JB/T 7303-1994 Technical requirements for road sweepers
- JB/T 3588-1994 Rolling bearings - Dimensions and tolerances of full complement needle roller bearings
- QB 1799-1993 Cold ground lemon oil
- GB/T 15064.3-1994 Test method for graphite emulsion of picture tubes - Test method for resistivity
- GB/T 17849-1999 Preparation of steel substrates before application of paints and related products--Test methods for non-metallic blast-cleaning abrasives
- GB 475-1996 Commercial coal sampling method
- GB/T 27844-2011 Chemicals—Solution/extraction behaviour of polymers in water
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:wymp4wang@gmail.com