INdex
GB standard
Standard category
Machinery Industry
It standard
Industry Standard
Chemical Industry It standard Petrochemical ZB Industry Light industry Railway industry Shipping industry Measurement standards

GB/T 15054.2-1994 Small thread diameter and pitch series

time: 2024-08-09 02:27:48
  • GB/T 15054.2-1994
  • in force

Basic Information

standard classification number

  • Standard ICS number:

    Mechanical systems and general parts >> 21.040 thread

  • China Standard Classification Number:

    Machinery>>General Machinery>>J04 Basic Standards and General Methods

associated standards

  • alternative situation:

    Part 193-1963

  • Procurement status:

    ≈ISO/R 1501-70

Publication information

  • publishing house:

    China Standards Press

  • Publication date:

    1995-03-01

Other Information

  • Release date:

    1994-05-03

  • Review date:

    2004-10-14

  • Drafter:

    Li Xiaobin, Yu Yuan, Yu Minhui

  • Drafting Organization:

    Mechanical Standardization Institute

  • Focal point Organization:

    National Thread Standardization Technical Committee

  • Proposing Organization:

    Ministry of Machinery Industry of the People's Republic of China

  • Publishing Department:

    State Bureau of Technical Supervision

  • Competent Authority:

    National Standardization Administration
Introduction to standardsDescription (Translated English) / download

Skip to download

Summary:

This standard specifies the diameter and pitch series of small threads whose tooth profiles conform to GB/T 15054.1. This standard applies to small threads for general use with a nominal diameter range of 0.3 to 1.4 mm. GB/T 15054.2-1994 Small thread diameter and pitch series GB/T15054.2-1994 Standard download decompression password: www.bzxz.net
Standard contentStandard content

Some standard content:

National Standard of the People's Republic of China
, Diameter and Pitch Series
Small Thread
Miniature Thread-General Plan This standard refers to the international standard ISO/R1501-70 "ISO Small Thread". Subject content and scope of application
This standard specifies the diameter and pitch series of small threads that conform to GB/T15054.1. This standard applies to small threads for general use with a nominal diameter range of 0.3~1.4mm. Reference Standard
GB/T15054.1 Small Thread Profile
3 Diameter and Pitch Series
GB/T15054.2-94
Replace the small thread part in GB193-63 Www.bzxZ.net
The diameter and pitch series are specified in the table. When selecting the diameter, the diameter of the first series in the table should be given priority. Diameter and pitch series
Nominal diameter
First series
Approved by the State Bureau of Technical Supervision on 1994-05-03 246
Second series
Implementation on 1995-03-01
Thread code
GB/T 15054.2—94
4.1 Small threads that conform to GB/T15054.1 standard are represented by S\. 4.2 For threads that meet the requirements of this standard, the size specification is expressed as "*nominal diameter". 4.3
When the thread is left-handed, "LH" shall be added after the size specification. Right-handed threads are not marked. Marking example
Left-handed thread
Nominal diameter
Additional instructions:
This standard is proposed by the Ministry of Machinery Industry of the People's Republic of China. This standard is drafted and managed by the Standardization Research Institute of the Ministry of Machinery Industry. The main drafters of this standard are Li Xiaobin, Yu Yuan and Yu Minhui. 217
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
  • Recommended standards
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：bzxznet@163.com