JB/T 6521-1992 General technical requirements for industrial boiler coal loading machines

This standard specifies the type, basic parameters, technical requirements, test methods, inspection rules and paint packaging of industrial boiler coal-loading machines. This standard applies to coal-loading machines for intermittent or continuous coal loading of single or multiple industrial boilers (hereinafter referred to as coal-loading machines). JB/T 6521-1992 General Technical Conditions for Industrial Boiler Coal-Loading Machines JB/T6521-1992 Standard download decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of China
General Technical Conditions for Industrial Boiler Coal Loaders
1 Subject Content and Scope of Application
JB/T6521-92
This standard specifies the type, basic parameters, technical requirements, test methods, inspection rules and paint packaging of industrial boiler coal loaders. This standard applies to coal loaders (hereinafter referred to as coal loaders) for intermittent or continuous coal loading of single or multiple industrial boilers. 2 Reference standards
GB9439
GB1804Www.bzxZ.net
GB1958
GB3768
JB419G
Gray cast iron parts
Gray cast iron mechanical properties test methods
Tolerances and fits Limit deviations of dimensions without tolerances Shape and position tolerances test regulations
Simplified method for determining the sound power level of noise sources
Manufacturing technical conditions for transmission and reduction gearboxes for boilers Models and basic parameters
3.1 Model
The model of the coal loader consists of two parts, which are connected in parallel. The first part is the structural type code of the coal loader, as specified in Table 1. The first digit of the second part, GS, indicates the code of the boiler coal loader, and the last digit indicates the rated evaporation capacity of the industrial boiler (for lifting and arm type coal loader) or the coal loading capacity (for scraper type coal loader), which is expressed in numbers. If it is a hot water boiler, the rated thermal power can be converted to 1t/h rated evaporation capacity according to 0.7MW rated thermal power.
Rated evaporation capacity (t/h); coal loading capacity (t/h) Code of boiler coal loading machine
Structural type code
Structural type of coal loading machine
Lifting type coal loading machine
Rotary arm type coal loading machine
Scraper type coal loading machine
3.2 Basic parameters
Approved by the Ministry of Machinery and Electronics Industry on December 21, 1992
Implemented on May 1, 1993
Basic parameters should be in accordance with the provisions of Table 2.
Note: 1) Inclination angle ≤ 30°
2) The unit is t/h.
6~10t/h
2~4 t/h
6~10t/h
JB/T6521-92
Coal loading capacity
0.05~0.10
0.15~0.20
0.10~0.35
Operating speed
0.12-0.20
0.035~0.050
0.09~0.12
3.3 Marking example
The lifting coal loader equipped with a boiler with a rated evaporation capacity of 4t/h or a rated thermal power of 2.8MW is marked as: TGS4. The scraper type coal loader with a coal loading capacity of 10t/h is marked as GGS10.4 Technical requirements
4.1 Requirements for parts manufacturing
4.1.1 General requirements
4.1.1.1 The coal loader shall be manufactured according to the drawings and technical documents approved by the prescribed procedures. 4.1.1.2 The main raw materials (including welding materials) shall comply with the design drawings and the relevant standards. Material substitution shall be approved according to the prescribed procedures and the substitution procedures shall be handled.
4. 1. 1.3
4. 1. 1. +
The mechanical properties of the castings shall comply with the provisions of GB9439. The castings shall be accompanied by a certificate of conformity. The machining dimensional deviation without tolerance shall be manufactured according to the IT14 level precision in GB1804. Purchased parts must be accompanied by a certificate of conformity or quality certificate before they can be used. 4.1.1.5
Outsourced parts must comply with the requirements of the design drawings and technical documents. 4.1.1.6
In addition to the requirements specified in the drawings, the welds of welded structures shall also meet the following requirements: There shall be no cracks, pores or slag inclusions on the weld surface. The height of the butt weld shall not be lower than the parent material, but the remaining height shall not exceed 3mm, and the weld and the parent material shall have a smooth transition. The height b.
of the fillet weld shall not have a negative deviation.
The undercut depth of the weld shall not exceed 1mm, the sum of the undercut lengths on both sides of the weld shall not exceed 15% of the total length of the weld, and the continuous undercut length c.
shall not exceed 50mm.
4.1.1.8 After welding, the steel structure shall have a smooth and flat appearance. 4.1.1.9 When bolts are connected, the screw hole position tolerance T, if not specified, shall comply with the following provisions: a.
When the connected parts are all plain holes:
When one of the holes of the connected parts is a screw hole:
Where: T--screw hole position tolerance value, mm; D-bolt hole diameter (basic size), mm;
d---bolt diameter (basic size), mm. T
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.