JB/T 8414-1996 Types and dimensions of drive shaft ends of oil pumps for internal combustion engines

This standard specifies the type and size of the oil pump drive shaft end. This standard applies to the design and manufacture of the drive shaft end of the oil pump (including gear pumps and rotor pumps) of small and medium power internal combustion engines. JB/T 8414-1996 Type and size of the oil pump drive shaft end of the internal combustion engine JB/T8414-1996 Standard download decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of China
.IB/T 8414-96
Oil pump for internal combustion engines
Types and dimensions of transmission shaft ends
Published on September 13, 1996
Ministry of Machinery Industry of the People's Republic of China
Implementation on July 1, 1997
Machinery Industry Standard of the People's Republic of China
Oil pump for internal combustion engines
Types and dimensions of transmission shaft ends
1 Subject content and scope of application
This standard specifies the types and dimensions of transmission ends of machine tools. JD/T 8414 96
This standard is applicable to small and medium-sized internal combustion engine oil systems (including active mountain range and the transmission of platinum carbon wave juice and washing reference standard difficult
J mouth hall
combustion pattern diameter and screw strength multi-row true diameter 1500mm
drawing blade raw figure 4 type
flat building profit to the south ruler square
flat chain end and injection world surface
semi-national chain type day small
national material step by step comprehensive flower lithium (tooth test certificate) tax effect source internal shape public examination matchingbZxz.net
3.1 cloud The difference between the two is the smallest after the 4-inch size. 3.2 The size of the transmission system products manufactured by the standard is only the size of the technical table "benefit climbing. Standard guide
4.1 The number of the transmission buckle is shown in the table 1,
4.2 The meaning
4., the form of the movement of the stock product proposal
33\Asymptotic spline
The hole is required in the class
with the hole, the pin
has the support
The Ministry of Machinery Industry 1996-09-1 approved
The transmission size, mm ||tt| |199T-0T-01 Implementation
Nano with technology
Shaped shaft with pattern
5 Types and dimensional parameters of transmission shaft ends
5.1 Specifications of Figure 1.1: L constant length
5.2 Specifications of the connection diagram and Table 2
JB/T94E4-96
Table 1 Dimensions of shaft ends
Specific dimensions
Standard specifications
Note: length is too long||t t||Basic size
JB841496
Table fan olive shaft size
Pole fruit mycelium
5.320 Gradient line flower modeling auxiliary according to Figure 3 and the provisions of the table 41.5×45
Table 32℃ odd open line flower plated shaft reduction
Pass through the positive cultivation for a long time
5.4 The shaft with a pin hole is according to the provisions of Figure 4 and Table 1. Tooth effect
L(dream*)
. (Table test)
Juice. Long bar selection
JB/T 8414-96
Table 4 has the size of the end of the turn with a pin hole
5. If there is a hole in the section, it is necessary to match the plate diagram and use the provisions of Table 5. :x:
Table with a misaligned support, tripod shaft end size
Qualified students choose
with a stopper control diagram Lika's specifications
Basic size
The size is the minimum size,
JB/T 8A14-96
Table 6 Small dimensions of shaft ends with stoppers
Basic civil nature limit
5.7 Shafts with threads shall comply with the provisions of Figure 7 and Draft 7. Note: JB/T841496
Table 7 Common dimensions of shafts with screws
5.8 Shafts with threads shall comply with the provisions of Figure 8 and Draft 8. Note: The dimensions of the tapered auxiliary ends of the shafts with threaded ends shall comply with the provisions of Figure 8. Additional notes: The National Technical Committee for Standardization of Internal Combustion Engines shall report to the National Technical Committee for Standardization of Internal Combustion Engines. The main drafter: Fu Zeming.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.