GB/T 5104-2004 Basic types and dimensions of 30° pressure angle involute spline hobs

This standard specifies the basic types and dimensions of hobs for integral involute splines with a module of 0.5mm to 10mm and a pressure angle of 30°. This standard applies to hobs for machining cylindrical spur involute splines with basic tooth profiles in accordance with GB/T3478.1 and dimensions in accordance with GB/T3478.2. Hobs are available in three precisions: A, B, and C. GB/T 5104-2004 Basic types and dimensions of hobs for involute splines with a pressure angle of 30° GB/T5104-2004 Standard download decompression password: www.bzxz.net

[C 25. 100. 25
National Standard of the People's Republic of China
GB/T5104—2004bZxz.net
Replaces G1T51641385
30°pressure angle involute spline hob
Basic types and dimensions
The basic types and dimensions of hohs for 3o\pressureangleinvolutesplines
Published on 2004-02-10
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China National Standardization Administration
Implemented on 2004-08-01
GB/T 5:04—2004
Standard B/T5104-8310\Pressure load type 4 and size 11335 are compared with the following main changes:
Compared with GB/T 5104
The 3.5 grid number in the structural number series is cancelled:
The two basic wood types in the standard are listed in Chapter 3;Added marking examples:
Rectified "Number series code.
This standard is attached with the appendix for material production. The standard is proposed by China Federation of Wood Industry. This standard is drafted by the National Technical Committee for Standardization, and the only one is the wood standard.
This standard is issued by the following person:-GR:T 510-1-19N5.
1 Range
30° pressure angle involute spline cutter
GB/T5104—2004
Basic type and size
The standard specifies the basic type and size of the involute spline with a modulus of 0.5m--1C and a remainder of 3. This standard is based on the BT3478.-. size and GB/T3-78.2. The new rolling force cutter with a maximum of 4, C Three degrees,
2 Implementation of referenced documents
The requirements in the following documents have become the policy provisions of this standard through the use of this standard. 5 Referenced documents with a certain date: their subsequent revisions are not applicable to this standard, however, all parties involved in the agreement reached under this standard are encouraged to use the latest versions of these documents, without noting the latest versions of the referenced documents. /T1 Circular pull involute Modulus and tolerance (GB/8-1ISA1981
GR/-118.2 Round tooth chain 10\ Pressure angle dimension table (G1/78.2195, nS0111981)
1310-2034 Involute chain hydraulic casting technology G613 Wanhe tool holder change size H-1993.mM1S04:197) 3 Types and dimensions
3.1 This type is divided into two types: type and type. Type 1 is a flat top tool, suitable for adding 1 flat tooth external chain type is a tooth top force, suitable for "working round tooth root external chain, 3.2 The required type and size of the involute flower hob are determined by the figure! And table! 3.3 The spline is made into a single head (according to the requirements of the user): the thread is parallel to the straight line of the rolling line, 3.4 The size of the bearing is guided according to the provisions of GB/T6132. 3.5 The diameter of the bearing block is determined by the minimum manufacturing method. GB/T51G4—2004 The first series The second series Example of the mold effect m=2, Class A precision internal single left involute spline is: full disconnection spline installation 239A1G/T14-2>04. 1.1 The slide rule is as shown in Figure 1.
Effective series
English series
Travel series
Branch diameter
ai/rmart
43, 55
x9, 42
$8, 32
Appendix A
Informative record:
Calculated dimensions of hobs
Associated quantities
Division of angles
Division of diameters
CH/T5104—2004
Government registration
GH/T 51042004
1 Informative appendix;
Axial tooth profile dimensions of hobs
Axial length dimensions of hobs according to B.1.
h, 0. 25 m
h..—1. 6 r(m:1. c0)
hr=1, 5 m(mt1. ()
-0.10m（.When the force is allowed, it is used to determine the direction）
"m-model efficiency;
Figure R,1
...1, 75 m(mc1.o)
n 1. 65 tot/n.1. 00)
r, -u.4 yn
(ra number
lubrication system
30°03
4, 715
5, 287
15,735
GB/T 5104—2004
n, :93
3, 446
E1, 447
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.