JB/T 8483.1-1996 Multi-purpose lathe accuracy inspection

From the date of entry into force of this standard, JB/GQ 1154-90 "Multi-purpose lathe accuracy" is invalid. This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of multi-purpose lathes. This standard is applicable to multi-purpose lathes with a maximum rotation diameter of 250~400mm on the bed and a maximum workpiece length of up to 1000mm. JB/T 8483.1-1996 Multi-purpose lathe accuracy inspection JB/T8483.1-1996 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
J/T8483.1-96
Multi-purpose lathe
1996-11-07 Issued
Precision Inspection
199-(1-1 Implementation
Ministry of Machinery Industry of the People's Republic of China
JD/T8483.196
Technical standard will be implemented from the date of entry into force, 18/Q1154-90 Multi-purpose lathe to operate.
This standard is proposed by the National Technical Committee for Standardization of Metallurgical Reduction Cutting Machine Tools. This standard is under the jurisdiction of Shan Shensa Lathe Research Institute, and the responsible unit for this standard is: Shanghai Ceshi-Machinery 1 Scope
Mechanical Industry Standard of the People's Republic of China
Precision Inspection
Multi-purpose lathe
The geometric accuracy and working accuracy requirements of the multi-purpose lathe in the non-standard factory are specified, so the inspection method is JB/I 8483.196
2 The standard is applicable to multi-purpose lathes with a maximum rotation of 250~-190mm and a maximum length of 1000mm. 2 Reference standards
The texts contained in the following standards are the referenced texts of this standard. When this standard is published, the versions shown are valid and all new versions will be revised; the parties using the standard should explore the possibility of continuing to use the latest versions of the following standards, [B2G7082 3 General requirements for the inspection of the accuracy of cutting machines
3.1 When using this standard, refer to J7. In particular, the installation of the machine, the idle operation of the ten axes and other components, and the inspection of the accuracy of the machine.
3. 2 This standard indicates the minimum precision of the items, and does not represent the actual order. For the purpose of installation inspection and inspection, the inspection can be carried out in any order.
3. When inspecting the working accuracy of this standard, the test piece should be inspected after fine turning. 3.4: * When the actual measured length is different from the length specified in the technical standard, the difference should be made according to the provisions of 7.3.1.1 of JB2G7082. When the result is 1c.mm, it should still be calculated as 0.005mm. 3.5 The direction parallel to the bed guide rail is called the weaving direction, and the horizontal direction from the lower number is the weaving direction. 3.6 Refer to 3.1 in JTI367082 to adjust the installation water level, and place the template in the guide position. At the west end of the bed guide rail (or through a special Month's storage board) Place the water meter, the readings of the half-meter car are not displayed as U. (8/0. Approved by the Ministry of Machinery Industry on 199611-07
Implementation on 1997-01-01
刺此铁域
S230'0
葡萄激草
JB/T8483.1
露当#
JI/T8483.1-96
2tSSWT
(8/0=7:
家源味
8t29#2*9
2b+'s'77''s'1''t9
(wwoot
不型士
JR/T 8483.1
6'838+
1319'823bzxz.net
More than the process
Medical new strong
2380223
t8875ss
1-05-r[
IB/T 8483.1
8483.1-96
52g'9+3''s
3'+'?'t'e's't''t's's
10'℃
FW constant installation
218932330
Three "9
Patch of ice purple installation
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.