QB/T 2376-1998 Method for compiling product models of wine-making machinery

This standard specifies the method for compiling the model of wine-making machinery products. This standard applies to wine-making machinery products. QB/T 2376-1998 Method for compiling the model of wine-making machinery products QB/T2376-1998 Standard download decompression password: www.bzxz.net

QB/T 2376—1998
The original Ministry of Light Industry standard QB917-1983 "Method for compiling wine-making machinery product models" has been abolished and is now revised on the basis of this standard.
This standard is proposed by the Quality Standards Department of the China Light Industry Association. This standard is under the jurisdiction of the National Technical Committee for Standardization of Wine and Beverage Machinery. The drafting unit of this standard: Guangzhou Machinery Design Institute of the China Light Industry Association. The main drafters of this standard: Zhan Liping and Xu Feng. 113
1 Scope
Light Industry Industry Standards of the People's Republic of China
Method for compiling wine-making machinery product models
This standard specifies the method for compiling wine-making machinery product models. This standard applies to wine-making machinery products.
2 Composition of main model
2.1 Composition of main model of wine-making machinery products:
Main parameters of the product
Product type code
Professional code of wine-making machinery
QB/T2376—1998
2.1.1 The professional code of wine-making machinery is represented by the capital “J” of the first letter of the Chinese pinyin character jiu (wine). 2.1.2 The product type code is represented by uppercase Chinese phonetic letters, and the first letters of the phonetic letters of the words with representative meanings in the product classification name are selected. Usually two letters are used, among which "I" and "O\ are not used. If repetition cannot be avoided, up to four letters can be used. 2.1.3 The main parameters of the product are represented by Arabic numerals and are specified as follows: 2.1.3.1 When the main parameters of the product are represented by one parameter, they are directly included in the latter part of the model. 2.1.3.2 When the main parameters of the product are represented by two (or more than two) parameters, these parameters should be separated by the following symbols in the latter part of the product model:
a) When the measurement units of the two parameters are different, they are separated by the center point symbol "·"; b) When the measurement units of the two parameters are the same, they should be separated by the symbol "×"; when the measurement units of the two parameters are the same but do not represent the same complete physical quantity, they are still separated by the symbol ". "Separated by ". 2.1.3.3 The commonly used measurement units in the parameters are shown in Table 1. Table 1
Name of quantity
Diameter, length, width, height
Processing capacity
3 Compilation of auxiliary codes
Millimeter, meter
Square meter
Liter, cubic meter
Common measurement units
Name of measurement unit
Ton, kilogram
Ton/hour, kilogram /hour
t/h,kg/h
Unit symbol
3.1 For derivative products with the same main structure and parameters, which are partially modified on the basis of the basic product to meet different usage requirements, the derivative code is represented by Roman numerals I, III, Asia... and is compiled after the main model. Approved by China Light Industry Federation on March 27, 1998
Implementation on December 1, 1998
QB/T2376—1998
3.2 For products with unchanged main structure but improved partial structure, capital letters A, B, C are used to represent them ("I" and "O" are not used).
3.3 When the main material of the product must be indicated in the model, it is indicated by the material code in brackets. For carbon steel and cast iron as the main material, no material code is added. The material code is shown in Table 2. Table 2 Material code
Material name
No Stainless steel
Engineering plastics
Material code
T(tong)
3.4 ​​The auxiliary code is directly added after the main model of the product. If there are several auxiliary codes at the same time, they are arranged in order of derived code, improved code, and material code.
Grape press
Screw diameter (mm)
Screw (luo) spinning (ya) pressing type
Wine making machinery
3. 6 X 1. 5
Wheat turning machine
-Nominal width (m) X wheat layer depth (m) Multi-row spiral type
Wine making machinerywwW.bzxz.Net
Cotton cake filter
Nominal diameter (mm)·Number of pieces
Cotton (mian) cake filter (lu) type
Wine making machinery
Fermentation tank
Derived products
Nominal volume (m)
One-tight (mi) closed (bi) type
One-wine making machinery
QB/T 23761998
Alcohol crude distillation tower
Main material: stainless steel
Nominal diameter (mm)
Circular bubble cap type
Wine making machinery
Malt mill
First partial improvement
Nominal processing capacity (t/h)
Horizontal roller type
Wine making machinery
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.