JB/T 10121-1999 Machine tool fixture parts and components - Quick-change chucks for lathes
time:
2024-08-12 02:15:01
- JB/T 10121-1999
- in force
Standard ID:
JB/T 10121-1999
Standard Name:
Machine tool fixture parts and components - Quick-change chucks for lathes
Chinese Name:
机床夹具零件及部件 车床用快换夹头
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12886-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
Mechanical Science Research Institute
Description (Translated English) / downloadSkip to download
Summary:
JB/T 10121-1999 This standard specifies quick-change chucks for lathes with workpiece diameters of 8 to 100 mm. This standard was first published in 1983 as JB 3395-83 and revised for the second time in 1991 as GB/T 12886-91. JB/T 10121-1999 Machine tool fixture parts and components Quick-change chucks for lathes JB/T10121-1999 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
IC5 28.060.41
Standard of the Machinery Industry of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06Publishedwww.bzxz.net
State Machinery Industry Bureau
2000-01-01Implementation
Standard of the Machinery Industry of the People's Republic of China
The parts and units of jigs and fixturesQuick change chuck for lathes This standard specifies the quick-change chucks for lathes with workpiece diameters of 14-25mm. 2 Dimensions are shown in the following figure and table. Approved by Beijing Machinery Industry Bureau in 1999-0A-06 312 JBt0121-1999 Implementation in 2000-01-01 Nominal self-diameter (applicable month! 3 Marking 3.1 Marking: JB/T 10121-1999 >18-25 >25-35 Quick-change chucks for lathes with nominal diameters of 14-28mm. Head 14~18101199
> 50 - 65
>65 ~ 80
8) [02
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06Publishedwww.bzxz.net
State Machinery Industry Bureau
2000-01-01Implementation
Standard of the Machinery Industry of the People's Republic of China
The parts and units of jigs and fixturesQuick change chuck for lathes This standard specifies the quick-change chucks for lathes with workpiece diameters of 14-25mm. 2 Dimensions are shown in the following figure and table. Approved by Beijing Machinery Industry Bureau in 1999-0A-06 312 JBt0121-1999 Implementation in 2000-01-01 Nominal self-diameter (applicable month! 3 Marking 3.1 Marking: JB/T 10121-1999 >18-25 >25-35 Quick-change chucks for lathes with nominal diameters of 14-28mm. Head 14~18101199
> 50 - 65
>65 ~ 80
8) [02
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB 14784-1993 Safety specification for belt conveyors
- GB/T 4958.7-1988 Measurement methods for equipment used in terrestrial radio-relay systems Part 2: Subsystem measurements Section 7: Transmitters
- GB 16191-1996 Hygienic standard for trifluoromethyl hypofluorite in workplace air
- GB 8234-1987 Castor seed oil
- QX/T 524-2019 X-band Doppler weather radar
- GB/T 20002.2-2008 Drafting for special aspects in standards - Part 2: The needs of older persons and persons with disabilities
- JB/T 7150-1993 Main inspection items and test methods for high-strength bolts for construction machinery
- SJ/T 10376-1993 General terms used for technological documents
- GB/T 15153.1-1998 Telecontrol equipment and systems Part 2: Working conditions Part 1: Power supply and electromagnetic compatibility
- GB/T 27859-2011 Chemicals—Sediment-water chironomid toxicity test—Spiked sediment method
- GB 7667-1996 Electron microscope X-ray leakage dose
- JB/T 5169-1991 Test method for pellet feed press
- QB/T 3634-1999 Phenolic tape bearing
- GB/T 5121.15-1996 Chemical analysis methods for copper and copper alloys - Determination of cobalt content
- JB/T 10241-2001 Metallic coatings — Decorative multicolours composite electyoplated coatings
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：wymp4wang@gmail.com