GB/T 15009-1994 Corrosion resistant alloy hot rolled plates

GB/T 15009-1994 Corrosion-resistant alloy hot-rolled plate GB/T15009-1994 standard download decompression password: www.bzxz.net

National Standard of the People's Republic of China
Hot-rolled plates of corrosion-resistant alloy
Ilot-rnlled plates of corrosion-resistingGB/T 15009—94
Replaces GBm 273 88
This standard is applicable to nickel-based and iron-nickel-based hot-rolled plates of corrosion-resistant alloys with a thickness of less than 4 mm (hereinafter referred to as plates). 1 Dimensions, shape
1.1 The dimensions and allowable deviations of the plates shall comply with the provisions of GB709—88 "Dimensions, shape, weight and allowable deviations of hot-rolled steel plates and strips".
1.2 The camber of the trimmed plates with a thickness of less than 10 mm shall not exceed 4 m per meter, and the plates with a thickness of more than 10 mm may not be trimmed.
1.3 The unevenness of the plate per meter length shall not exceed 8 mm, but the unevenness of the plate with a tensile strength of 685N/mm2 per meter length may not exceed 14mm.
2 Technical requirements
2.1 Brand and chemical composition
2.1.1 Alloy brand and chemical composition (melting analysis) shall comply with the provisions of Table 1. 2.1.2 When conducting finished product analysis, deviations from the provisions of Table 1 are allowed, but the maximum allowable deviation value shall comply with the provisions of Table 2 in GB/T 15007 Corrosion-resistant alloy brands.
2.2 Delivery status
The plate is delivered after being treated and pickled.
2.3 Mechanical properties
The mechanical properties of the plate after solidification treatment shall comply with the provisions of Table 2. The strength value instrument shall be measured only when the purchaser requires (specified in the contract).
2.4 Macro inspection
The cross-sectional acid-immersion macro inspection of the plate (or plate) shall not have any residual shrinkage, cracks, delamination and inclusions visible to the naked eye. 2.5 Surface quality
2.5.1 The material shall not have delamination. There shall be no cracks, bubbles, fire impurities, scars, oxide scale and over-pickling on the surface. 2.5.2 The surface is allowed to have pits, pits, scratches and rough surfaces with a depth not greater than half of the plate thickness tolerance and not less than the minimum thickness allowed. Any defects exceeding the above-mentioned Yao Yao can be removed by grinding. The depth of local defect cleaning shall not make the plate less than the minimum thickness allowed.
2.6 Special requirements
Under the condition of having technical basis, according to the requirements of the purchaser, special requirements such as chemical composition and mechanical properties can be supplemented, or special inspection items such as brain erosion test and non-destructive testing can be supplemented, but the specific requirements and test methods should be determined by negotiation between the supply and demand parties. 3 Test method
The test method, sampling rules and number of joint samples for plates shall comply with the requirements of Table 3. Approved by the State Bureau of Technical Supervision on April 4, 1994, and implemented on May 1, 1994
0. 05 ~ 0. 10
.0.020
GB/T15009—94
19.0~23.030,0~35. 0
19. 0~-23. 0
30. 0 ~ 35. 0
19. 0~21. 0
42.0~44.0
25. 0~27. 0 34. 0~37. 0
19. 5 ~ 23. 5
38.0~-46.0
28. 0~-31. 0
11. 0~17. 0
21. 025. 0
35. 0~ 38. 0
14. ~~17. 0
14. 5--16. 5
114.5~16. 5
14.0--18.0
20. 0~-23, 0
0. 15 ~ 0. 60
0.15~0.60
0. 40 ~0. 90
0. 60~1. 20
0. 40 ~0. 90
L2.5~13. 5
2. 0~3. 0
2. 5 ~ 3. 5
6. 0--10. 0
10. 0 ~ 15. 0
26.0~30.0
4. 0 -- 6, 0
4. U ~ 7. 0
4. 0-7. 0
3. 15~4. 15
26. 0~30. 0
2. 0 ~-3. 0
15. 0 ~ 17. 0
15. 0 ~17. 0
14. 0~17. 0
8. ~10.0 i
3. 0 ~ 1. 5
3. 0 ~-4. 5
3. 0~4. 0
.0.030
0. 15~0, 60
0. 15 ~ 0. 60
.0. 30bzxz.net
1100~1170
1160~121n
1000~-1050
1020~1070
1 050~1100
1000105
1100--1160
1 n80 1 130
1140~1190
1n40~1 090
1050~1100
11601210
1150~1 200
1 050 --1 100
11001:0
Inspection items
Chemical analysis
Low-deposit structure
Mechanical properties
Surface quality
Ultrasonic wave flaw detection
Corrosion test
n/T15009--94
Test method
GB223, GB1467-78
GB/T 149SS.2--54
(GI 228- 87
Visual inspection
Visual inspection
General tools
For scientific performance
Not less than ten
Sampling rules
GB22284
Equivalent to ten samples
GB2975
82.GB639786
Sampling number
Each furnace
Each one
Equivalent to two
The general provisions for plate acceptance shall comply with the provisions of GB247-R8 General provisions for acceptance, packaging, marking and quality certificate of steel plates and strips 4.1
4.2 The test results of chemical composition, mechanical properties, surface quality, size and appearance shall comply with the provisions of the relevant text of this standard. However, mechanical test can be omitted if agreed by the purchaser. Packaging, marking and quality certificate
GB/T 15009-94
Plate packaging, marking and quality certificate shall comply with the relevant provisions of GB247--88. Additional remarks:
This standard was proposed by the Information Standard Research Institute of the Ministry of Metallurgical Industry of Shanxi Province. This standard was drafted by the Changcheng Steel Plant of the Metallurgical Industry. This standard is the level mark B/T150u9-941
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.