JB/T 8006.4-1999 Machine tool fixture parts and components movable handle clamping screws
time:
1999-08-06 15:00:00
- JB/T 8006.4-1999
- in force
Standard ID:
JB/T 8006.4-1999
Standard Name:
Machine tool fixture parts and components movable handle clamping screws
Chinese Name:
机床夹具零件及部件 活动手柄压紧螺钉
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
JB/T 8006.4-1995 (original standard number GB/T 2163-1991)
Description (Translated English) / downloadSkip to download
Summary:
JB/T 8006.4-1999 JB/T 8006.4-1999 Machine tool fixture parts and components movable handle clamping screw JB/T8006.4-1999 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
ICS 25. 080. 01
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
State Machinery Industry Bureau
Implementation on 2000-01-01
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixturesMovable handle holddown screw
This standard specifies the movable handle holddown screw with thread specifications of M6 to M24. 2 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Corporation 1999-08-06 approved 34
JB/T8006.4—1999
Replaced JB/T8006.4—1995
2000-01-01 implemented
3 Marking bzxZ.net
3.1 Marking example:
JB/T8006.4—1999
d=M12, L=60mm A-type movable handle clamping screw AM12×60 JB/T8006.4—199990
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
State Machinery Industry Bureau
Implementation on 2000-01-01
Standard of the Machinery Industry of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixturesMovable handle holddown screw
This standard specifies the movable handle holddown screw with thread specifications of M6 to M24. 2 Dimensions
The dimensions are shown in the following figure and table.
National Machinery Industry Corporation 1999-08-06 approved 34
JB/T8006.4—1999
Replaced JB/T8006.4—1995
2000-01-01 implemented
3 Marking bzxZ.net
3.1 Marking example:
JB/T8006.4—1999
d=M12, L=60mm A-type movable handle clamping screw AM12×60 JB/T8006.4—199990
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- HG/T 2856-1997 Mepiracetam (Mepiracetam) technical
- QB/T 1974-2004 Shampoo (cream)
- GB/T 15448-1995 Fixed capacitors for electronic equipment Part 19: Sectional specification Metallized polyethylene terephthalate film dielectric DC chip fixed capacitors
- GB/T 8563.1-2005 Classification and codes for information of reward and disciplinary action—Part 1:reward code
- GB/T 15055-1994 Limit deviations of dimensions of stamping parts without tolerances
- HG/T 3578-1986 Serpentine Ore
- GB 12987-1997 Concrete circular hole plates for farm houses
- GB 3736.2-1983 Compression-type tapered thread long connector
- JB/T 6009-1992 Technical requirements for water tanks of small power diesel engines
- GB/T 3098.13-1996 Mechanical properties of fasteners - Torque test and breaking torque of bolts and screws - Nominal diameter 1?10mm
- GB/T 18894-2002 STANDARDs of electronic records filing and management
- GB 5059.1-1985 Chemical analysis methods for ferromolybdenum - Determination of molybdenum content by 8-hydroxyquinoline gravimetric method
- JB/T 8004.1-1999 Shouldered hexagon nuts for machine tool fixture parts and components
- GB/T 4678.9-2003 Die casting parts Part 9: Ejector plate guide pins
- GB 50288-1999 Code for design of irrigation and drainage projects
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：wymp4wang@gmail.com