CB* 82-1988 Journal diameter of ship shafting
time:
2024-10-21 05:11:45
- CB* 82-1988
- in force
Standard ID:
CB* 82-1988
Standard Name:
Journal diameter of ship shafting
Chinese Name:
船舶轴系轴颈直径
Standard category:
Ship Industry Standard (CB)
-
Date of Release:
1988-05-25 -
Date of Implementation:
1988-12-01
China Standard Classification Number:
Ships>>Marine Main and Auxiliary Engines>>U48 Shafting Equipment
alternative situation:
CB* 82-78
Description (Translated English) / downloadSkip to download
Summary:
CB* 82-1988 Ship Shafting Journal Diameter CB*82-1988 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
Professional Standard of the National Technical Committee for Ship Standardization CB *82—88
Neck diameter of ship shafting
Published on May 25, 1988
National Technical Committee for Ship Standardization
Implemented on December 1, 1988
Professional Standard of the National Technical Committee for Ship StandardizationNeck diameter of ship shafting
Subject content and scope of application
This standard specifies the neck diameter of ship shafting. CB*82--88
Classification number: U48
Replaces CB*82—78
This standard applies to the journal diameter of the sliding intermediate bearing, thrust bearing and bulkhead stuffing box of the ship shafting. This standard does not apply to the journal of the propeller shaft and the journal supported by the rolling bearing. 2
Neck diameter supported by sliding bearing
The journal diameter supported by sliding bearing is shown in the figure and table below. 7bzxz.net
Note: ① Avoid using the dimensions in brackets 50 as much as possible
② The relationship between the journal diameter 1z1 of the intermediate shaft and thrust shaft and the basic diameter (D> should meet the following requirements: when D<300mm, Dz+5mm;
When D=300~500mm.z~n+（5~10）mm; when D>500mm, Dz≥（10~20）mm③ The R angle is not less than F0.1D.
Approved by the National Technical Committee for Ship Standardization on May 25, 1988 (65)
Implemented on December 1, 1988
Additional remarks:
CB *8288
This standard was proposed by the Ocean Transport Ship Subcommittee and is under the jurisdiction of the Shanghai Ship Design and Research Institute. This standard was drafted by the 708th Institute of the 7th Research Institute of China State Shipbuilding Corporation. The main drafters of this standard are Zheng Yuanfang and Hu Zhengqin.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Neck diameter of ship shafting
Published on May 25, 1988
National Technical Committee for Ship Standardization
Implemented on December 1, 1988
Professional Standard of the National Technical Committee for Ship StandardizationNeck diameter of ship shafting
Subject content and scope of application
This standard specifies the neck diameter of ship shafting. CB*82--88
Classification number: U48
Replaces CB*82—78
This standard applies to the journal diameter of the sliding intermediate bearing, thrust bearing and bulkhead stuffing box of the ship shafting. This standard does not apply to the journal of the propeller shaft and the journal supported by the rolling bearing. 2
Neck diameter supported by sliding bearing
The journal diameter supported by sliding bearing is shown in the figure and table below. 7bzxz.net
Note: ① Avoid using the dimensions in brackets 50 as much as possible
② The relationship between the journal diameter 1z1 of the intermediate shaft and thrust shaft and the basic diameter (D> should meet the following requirements: when D<300mm, Dz+5mm;
When D=300~500mm.z~n+（5~10）mm; when D>500mm, Dz≥（10~20）mm③ The R angle is not less than F0.1D.
Approved by the National Technical Committee for Ship Standardization on May 25, 1988 (65)
Implemented on December 1, 1988
Additional remarks:
CB *8288
This standard was proposed by the Ocean Transport Ship Subcommittee and is under the jurisdiction of the Shanghai Ship Design and Research Institute. This standard was drafted by the 708th Institute of the 7th Research Institute of China State Shipbuilding Corporation. The main drafters of this standard are Zheng Yuanfang and Hu Zhengqin.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 8331-1996 Universal rotary head milling machine accuracy
- JB/T 3627.3-1999 Tools and accessories for assembly of modular fixtures - T-shaped four-jaw wrenches
- GB/T 14601-1993 High-purity ammonia for use in the electronics industry
- HG/T 20702.2-2000 The relationship between special equipment disciplines and other disciplines during the engineering design phase
- JB/T 3344-1993 Condenser performance test procedures
- GB/Z 18620.3-2002 Specification for cylindrical gear inspection Part 3: Gear blanks, shaft center distance and axis parallelism
- JB/T 5910-1997 Electrostatic precipitator
- GB 8287.1-1998 High voltage post porcelain insulators Part 1: Technical requirements
- GB/T 27908-2011 Performance improvement of management systems—Guidelines for procedures and methodology for continual improvement
- GB/T 2884.1-1996 Yangtze River Sectional Barge Model Standard Series--Yangtze River 3000-ton Sectional Barge Model Standard
- JB/T 5688.2-1991 Peanut shelling machine test method
- HG/T 3499-1983 Chemical reagent 1,4-dioxane (formerly HG/T 3-1529-83)
- JB/T 6839-2002 Classification of projection screens
- HG/T 20590-1997 Technical regulations for design of wastewater treatment in sulfuric acid and phosphate fertilizer industries
- YB/T 172-2000 Quantitative phase analysis of silica bricks by X-ray diffraction method
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：[email protected]