QB/T 2194-1996 Steel Paper Base

This standard specifies the technical specifications of steel paper base paper. This standard applies to base paper specially used for chemical processing to produce various steel paper boards and steel paper tubes. QB/T 2194-1996 Steel Paper Base Paper QB/T2194-1996 Standard download decompression password: www.bzxz.net

QB/T 2194-1996
This standard adopts the former Soviet Union's "OCT3436--1969 "Fiber Paper Base Paper" in a non-equivalent manner. This standard replaces QB550-1981 "Fiber Paper Base Paper", and divides the original standard's five product numbers into Type 1, Type I, and Type II according to their uses, and adds some content such as inspection rules.
This standard implements (50±2)%rh., (23±1)℃ test atmospheric conditions. This standard was proposed by the Food Papermaking Department of the China Light Industry Association. This standard is under the jurisdiction of the National Papermaking Standardization Center. The drafting unit of this standard: Mudanjiang Hongqi Paper Factory. The main drafters of this standard: Guan Shengjin, Liu Yuqin. From the date of implementation of this standard, the former Ministry of Light Industry Standard QB550-1981 "Fiber Paper Base Paper" will be invalid. 383
1 Scope
Light Industry Standard of the People's Republic of China
Fiberboard
This standard specifies the technical specifications of fiberboard. This standard applies to the base paper specially used for chemical processing to produce various fiberboards and fiberboard tubes. 2 Referenced Standards
QB/T 2194-—1996
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T450—1989 Sampling of paper and paperboard samples GB/T451.1—1989 Determination of size and skewness of paper and paperboard GB/T451.2—1989 Determination of basis weight of paper and paperboard GB/T451.3-1989 Determination of thickness of paper and paperboard GB/T453—1989 Determination of tensile strength of paper and paperboard (constant rate loading method) Determination of capillary absorption height of paper and paperboard (Krem's method) GB/T 461.1—1989
GB/T 462—1989
GB/T463-
GB/T 1541--1989
GB/T 2828—1987
Determination of moisture content in paper and paperboard
Determination of ash content in paper and paperboard
Determination of dustiness in paper and paperboard
Counting sampling procedure and sampling table for batch inspection (applicable to inspection of continuous batches) GB/T 10342—1989
GB/T 10739—1989
3 Product classification
Paper packaging and marking
Standard atmosphere for sample handling and testing of pulp, paper and paperboard 3.1 Steel paper base paper can be divided into three types according to its use: I, II and III. Type I is used for the manufacture of hard steel paperboard or soft steel paperboard for aviation components; Type I is used for the production of steel paper tubes; Type III is used for intermittent or continuous steel paper machines to produce steel paperboard, electrical insulation steel paperboard, high-strength steel paperboard, thick steel paperboard and sliver tube steel paperboard or reel steel paperboard. 3.2 The steel paper base paper is a roll paper with a roll diameter of 600mm~800mm or as specified in the contract. 3.3 The roll width is 800mm, 1500mm for type 1, 800mm for type 2, 1450mm, 1500mm, 1600mm for type Ⅱ or as specified in the contract. The width deviation shall not exceed ±3mm.
4 Technical requirements
4.1 The technical indicators of steel paper base paper must comply with the provisions of Table 1, or base paper with other water absorption or special requirements can be produced according to user requirements. Approved by China Light Industry General Association on January 31, 1996
Implemented on September 1, 1996bzxz.net
Transverse quantitative difference
Breaking length
Water absorption
Indicator name
0.5mm2~2.0mm2Not more than
12.0mm*~3. 0mm2 not more than
3.0mm2 or more
70g/m2
80g/m2
90g/m2
QB/T2194-1996
not more than
not more than
not less than
not less than
not more than
not more than
mm/10min
piece/m2
The ash content of the base paper for producing non-electrical insulating steel paperboard is allowed to be no more than 2%. 4.1.1
4.2 The appearance quality of steel paper base paper shall meet the following requirements. Type
45～55
35～45
4.2.1 Steel paper base paper is pink, and base paper of other colors can be produced according to the order contract. 4.2.2 Paper should be dyed with dyes that are stable in zinc chloride solution. The color of the paper should be uniform, and the same batch of paper should not have obvious color differences.
4.2.3 The fiber structure should be uniform, and no obvious cloud flowers are allowed. The standard paper sample at the time of ordering shall prevail. 4.2.4 The paper surface should be flat, and there should be no dead folds, metal pieces, oil stains, damage, moisture, paper edges and other paper diseases that affect use. 5 Test method
5.1 Quantification shall be carried out in accordance with the provisions of GB/T451.2, and the cross-section quantitative difference shall be measured with a 100mm×100mm sample. 5.2 Tightness shall be carried out in accordance with the provisions of GB/T451.3. 5.3 The tearing length shall be measured in accordance with the provisions of GB/T453. 5.4 Water absorption shall be measured in accordance with the provisions of GB/T461.1. 5.5 Ash content shall be measured in accordance with the provisions of GB/T463. 5.6 Water content shall be measured in accordance with the provisions of GB/T462. 5.7 Dust content shall be measured in accordance with the provisions of GB/T1541. Inspection rules
6.1 The sampling and pre-test treatment of the sample shall be carried out in accordance with the provisions of GB/T450 and GB/T10739. 6.2 The manufacturer shall ensure that the paper produced meets the provisions of this standard, and the quantity delivered each time shall be considered as a batch. 6.3 The user has the right to inspect whether the product meets the requirements in accordance with this standard. If the user has any objection to the quality of the product, he shall submit it to the manufacturer within three months after the arrival of the product, and jointly sample and re-inspect it or entrust a jointly agreed inspection department to re-inspect it. If it does not meet the provisions of this standard, it shall be judged as a batch unqualified. The manufacturer shall be responsible for handling it.
QB/T2194--1996
6.4 Delivery inspection sampling inspection shall be carried out in accordance with GB/T2828. 6.5 Delivery acceptance item grouping, acceptable quality level (AQL) and sampling plan shall be in accordance with Table 2. Table 2
Sampling plan
1～15
26～90
Inspection level 1
Normal inspection Secondary sampling plan
Class B nonconforming products
Sample size
7 Marking, packaging, transportation, storage
Class C nonconforming products
Nonconforming classification
Class B nonconforming
Water absorption
Breaking length
Dust degree
Class C nonconforming
7.1 Packaging and marking shall be carried out in accordance with the provisions of GB/T10342, and the following supplements shall be made. 7.1.1 The roll should be tight, with uniform tightness across the entire width, the two end faces should be neat, the concave and convex should not exceed 20mm, the number of joints in the roll should not exceed 3, and it should be marked with paper labels of different colors from the base paper.
7.1.2 It must be packed with 4 to 6 layers of wrapping paper with a weight of not less than 80g/m2, a glue application degree of not less than 0.75mm, and a width equal to the paper width, and then wrapped with a plastic flat belt twice (one at a distance of 15.0cm from the end). No glue is allowed to fall on the end of the roll when packing. 7.1.3 For long-distance transportation, it must be wrapped with a layer of fully enclosed plastic cloth and then wrapped with full-width straw rope. 7.2 The product should be stored in a dry warehouse to prevent the influence of rain, snow and ground moisture. 7.3 It should be kept clean during transportation and should not collide with hard objects such as iron and stone to avoid damaging the paper. 7.4 It must be stored separately according to grade, specification and production time. 7.5 The stacking height shall not exceed three rollers. When transporting or stacking, the roll shall not be thrown from a high place to avoid damaging the paper. 7.6 Before using the base paper, it should be guaranteed to have a natural storage balance period of more than three months. 386
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.