GB/T 3852-1997 Coupling shaft hole and connection type and size

This standard specifies the shaft hole and connection type, size and marking of the coupling. This standard applies to couplings with cylindrical shaft holes, 1:10 conical shaft holes and spline holes of key connection, interference fit seamless connection, expansion sleeve connection. GB/T 3852-1997 Shaft hole and connection type and size of coupling GB/T3852-1997 Standard download decompression password: www.bzxz.net

GB/T3852
The cylindrical and 1:10 conical shaft hole dimensions in this standard are not equivalent to the international standard 1S0/R775 "Cylindrical and 1:10 conical shaft extensions (edition 1969)".
This standard is a revision of the original (B3852-83 "Types and dimensions of coupling shaft holes and keyways". The main differences between this standard and the original GB385283 are: limiting the use of long cylindrical shaft holes. Adding 1:10 short tapered shaft hole size series and spline, expansion joint and keyless connection types.
This standard will replace GB385283 and this standard from the implementation month. This standard was proposed by the Ministry of Machinery Industry of the People's Republic of China. The National Technical Committee for Standardization of Machine Shafts and Accessories belongs to this standard! The drafting unit of this standard: Xi'an Heavy Machinery Research Institute of the Ministry of Machinery Industry. The main drafters of this standard: Li Yusheng and Zhang Guangyong. 1 Scope
National Standard of the People's Republic of China
Types and dimension for couplinghores and their connection
This standard specifies the shaft hole and connection type, size and mark of the coupling GB/T3852
Generation group 385283
This standard applies to the cylindrical shaft hole of key connection, keyless connection, expansion sleeve connection, 1:10 conical shaft hole and spline connection spline hole coupling
2 Reference standards
The provisions contained in the following standards constitute the provisions of this standard through opening in this standard. When this standard is published, the versions shown are valid. All standards will be revised. All parties using this standard should explore the possibility of using the latest versions of the following standards. G 1095
Gl;1111
GB/T1181
Profile dimensions of keys and keyways
Dimensions, tolerances and inspection of profiled splines
1996Tolerances of form and position without metric values ​​(GB 1570)
GB/T 3178. 1
GB/T 3178. 2
GB/T 3178.3
GB/T 3178. 1
G8 501
GB 11331
JB/TG136
Example of tapered shaft extension
Example of cylindrical involute spline module basic tooth profile tolerance cylindrical spur involute spline
30° pressure angle scale table
Spur involute spline
37.5° pressure angle dimension table
15 Force angle scale table
Cylindrical spur involute spline
Elastic pin coupling
Tapered male shaft
J1:T7931
Hydraulic assembly and disassembly of through-basin fitting
Tensioning coupling sleeve type and basic dimension
73 J19 011
GI (IZ, GICLZ type drum gear coupling 89
3 Types and codes
3.1 Shaft hole type and code see Table 1.
3.2 Connection type and code see Table 2
Approved by the State Bureau of Technical Supervision on December 1, 1997 and implemented on July 1, 1998
K National-shaped shaft hole
Glazed shaft hole with countersunk hole
Network-shaped shaft with flow hole
Type and code
J: Type
GB/T 3852 1997
Limited to long round consumable
Shaft extension motor end
Recommended
Recommended
Long round conical shaft hole with countersink
Long conical shaft hole without countersink
Short conical shaft hole with countersink
Type and codebzxz.net
GB/T 3852-1997
Table 1 (continued)
Xi'an City Management and Health Transmission
To Wuduhua!
Table 2 (end)
Shenzhen double-joint machine
Minwei shaft type single chain machine
Cylindrical shaft hole common cutting machine
Type and code
Conform to GB 1111
GB/T 3852 -1997
Table 2 (continued)
National straight line involute machine
Cylindrical joint joint
Stepped national cylindrical joint
Type and code
Conform to G1/3178
GB/T 3852
Table 2 (continued)
Over-connection
Expansion joint
Type and code
GB/T3852
Table 2 (end)
Note: The taper of the cone interference connection shaft hole (UZ type) shall comply with the provisions of JB/T6136. 4 Dimensions
4.1 Shaft hole dimensions
4.1.1 The diameter and length of the cylindrical shaft holes of type Y, J, and J. shall comply with the provisions of Table 3; the diameter and length of the conical shaft holes of type Z, Z., and 2. shall comply with the provisions of Table 4.4.2 Connection dimensions
4.2.1 The dimensions of the keyways of type A, B, B and 1) shall comply with the provisions of Table 3; the dimensions of the keyways of type C shall comply with the provisions of Table 4. 3852--1997
24-56-0
GB/T 3852 --- 1997
8—4-5
GB/T 3852
0-0-0-0-0
GB/T 3852-.. 1997
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.