JB/T 9019.1-1999 Screw-type gate hoist types and basic parameters

JB/T 9019.1-1999 JB/T 9019.1-1999 Screw-type gate hoist types and basic parameters JB/T9019.1-1999 Standard download decompression password: www.bzxz.net

JCS 47.020.40
Machinery Industry Standard of the People's Republic of China
JB/T9019.1~9019.2—1999
Screw Hoist
Headstock gears with screw hoist
1999-6-28 Issued by the State Machinery Industry Bureau, implemented on January 1, 2000, JB/T9019.1-199. This standard is a revision of the ZDJB6001.1, 89 screw starter type and parameters. During the revision, the original standard was comprehensively modified. The main technical content was not cavitated. The standard replaced the Appendix A of the standard H86.1-8 from the actual version. It is a reminder appendix. This standard was developed and coordinated by the Beijing Hoisting and Conveying Machinery Research Institute. This standard is the responsibility of the Shijiazhuang Mining Machinery Research Institute. This standard is for the purpose of engineering maintenance and non-compliance. 【Scope
Machinery Industry Standard of the People's Republic of China
Screw Gate Hoist
Types and Basic Parameters
Herdstockgearswib serewstem
-Trpes nnd hasic parameters
This standard strictly describes the types, basic symbols and connection dimensions of screw gate hoists, JB/T9019.1-1999
Replaces ZB386001.189
This standard is applicable to screw gate hoists (hereinafter referred to as gate hoists) for flat gates in water conservancy, hydropower and municipal water supply and drainage projects. 2 Types
2.1 Gate hoists are divided into two series: general type and remote control type. Each series is divided into two types: single-point and double-point. The general single-point opening machine has both manual and electric driving modes. The appearance of the closing machine is shown in Figures 1-3:
National Machinery Industry Bureau 1999-06-29 Approved for dynamic screw-type opening machine
2000-01-01 Note: The external diagram of the model is for special construction, JB/T9019.1-1999 2 Single-point screw-type gate hoist 3 Double-point screw-type gate hoist 2.2 The codes for the same type of gate hoists are as follows: 1BT9019.1-1999 a) General lifting screw-type gate hoist, its code is QP b) Control screw type gate hoist, its code is YL e) Common dynamic lever gate hoist, its code is Q 2.3 Gate hoist model representation method ×;
I Single channel type: QPL
Opening machine code: Access control type: QYL
Manual type: Qt.
2.4 Marking 5
Door force of 50N single-point lever closing machine: shoulder machine QY1-50JBT9019.1—:999
Opening six 80kN ordinary double-point lever opening machine: closing machine QPL-2×80JB/T9019.1—1999 moving screw opening machine with a force of 20kN: machine Q-20JB9019.1—1
3 Basic test data
3. [The basic parameters of the shoulder closing machine should comply with the table [~table 3.2 When the door height is greater than the value listed in the installation, the closing force should be appropriately reduced, and the total reduction is the connection record A (Appendix: Check, 3.3 The connection between the gate hoist and the door should comply with the requirements of 4. 3.4 The relationship between the axis and the size of the expenditure and the center of the hanging point of the double-hanging-point gate hoist is as follows: Table 5. r6s1e
Basic state number
Spiral gate height
Opening and closing speed
Spiral diameter
Spiral length
Motor power machine
nwan:n
QPF-30
QYI,-30
Tr50×[2
QP1-50
QYL-50
Jrg516
: Based on Italian generosity.
This Li Min
Shop door high quality
Room speed management
Fangu path
QPL2×50
QYL-2 × 50
T65-15
Center of the hanging point
Middle energy of the plate
JR/T90J9.1—1999
QPL-8G
QYL-80
QY1-125
QPT-160 QPL-200
Tr20-1
QYL·200
QY=250bZxz.net
Tie-20
OPL2 ×80 QPL2×100
oP2×125,QL2×[60
opt.-2 ×25 center
QPL-2 ×2G0
QYL-2× 80 QYL-2 × 100 QYL-2 × [23:0Y1-2 ×162 × 80
2 × 40
Tr75×16
solid shaft
Tr85×18
To spindle
3 x 80
1790×16
QY1-2 × 20CQYL-2 × 240
2 × 209
2 ×10
I'r95x18
2×259
2 × 125
Tr00-2
Interruption 12!
With support fixed space
JBET501.1-1999
(Appendix of prompt)
According to the relationship between rod length and closing force
】Under the full consideration of closing force ratio, the relationship between the best length and closing force is shown in Figure A1 2C
The line numbers corresponding to various door opening methods in the figure are as follows: 00
I30EX:250kN:280kX;4ID0kN:
5J25 kN:6160k.V;7200 kX:..250 kN120130
MingJkN
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.