JB/T 5562-1991 Roller motor reducer

This standard specifies the type, size and technical requirements of five series of roller motor reducers: YZD, YGL, YZL, YGX and YZX. This standard is mainly applicable to single insecticide drive transport rollers of rolling mills (transmission ratio i ≤ 12.5) and continuous casting machines (i ≥ 2). Its load characteristics are frequent starts, starting with load, and running in both forward and reverse directions. It can also be used for other mechanical transmissions with similar or lighter loads. The working environment temperature is -40~50℃; when it is lower than 0℃, preheating should be done before starting; when it is higher than 40℃, cooling measures should be taken. JB/T 5562-1991 Roller motor reducer JB/T5562-1991 Standard download and decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of China
Roller Motor Reducer
1 Subject Content and Scope of Application
JB/T5562·--91
This standard specifies YZD) , YGI, YZI., YGX, YZX five series roller table motor reducer type, size and technical requirements. This standard is mainly applicable to rolling mill transmission ratio 3 12.5) and continuous casting machine (3 25) independent drive transport roller table. The load characteristics are frequent starts, starting with load, and running in both forward and reverse directions. It can also be used for other mechanical transmissions with similar or lighter loads. The working environment temperature is...1~50)C; when it is lower than 0C, preheating should be above 40C before starting, and cooling measures should be taken. 2 Reference standard
GB 191
GB1184|| tt || GB1356 | | tt | |tt||Involute cylindrical gear module
Gray iron parts
GB10095
Involute cylindrical gear
Accuracy
GB11368||tt ||Gear transmission cleanliness
ZB J19 004
ZBJ19005
JB1799
JB2759
JB3251
cylindrical gear reducer|| tt | | tt | The types and dimensions of series motor reducers are shown in Figure 2 and Table 2. The types and dimensions of 3.3Y (GX and YZX series motor reducers are shown in Figure 3 and Table 3. Approved by the Ministry of Mechanical and Electronics Industry of the People's Republic of China on August 14, 1992 -07-01 Implementation
JB/T5562
Quality
attack
527|| tt||189
OFW2EICZA
GTWzEIZAbzxZ.net
20'2CZA
No.|| tt||type
JB/T5562-
5| |tt||5
器||tt ||出
OO| |tt||905
0||tt ||088
O||tt| |来
268|| tt||2
356||tt ||326
22 091IZA
ZIEITZA
2I281TZA
21081
JB/T5562-
181||tt ||s
91|| tt||5
98||tt| |5
H| |tt||
??????
929|| tt||S
18||tt| |992
4| |tt||8
591||tt ||5982
H|| tt||088
190［
9||tt ||13611
W091XA
[F \1091XA
1Z\WZSIXDA
1'W281X9A
代号与服务
JB/T 5562--91
YZG型电影（Y系统能道电视三相异步电视）与单级圆柱道道通销器下载电影roll道电视图销器系统代号。
一YGA型电影（Y系统roll道通信三相异步电影）与两级圆柱gear器电影道道电器线销器系统代号。
4.3Y71.--YZG型电影与两级圆柱gear店速器电影自道电器线速器系统代号。4.4YGX——YGAG型电影与行识开开凯速器任了roll道电器线速器系统代号。4.5YZX-—--YZG型电影与设计通销器安全roll道电器系销器系统代号。4.6 结果在线
YZn||tt| |YGX
5报看最佳
5.1机体
公称传动比1=2.5| |tt||凯速器包装，中心图器=10cm
Y系列roll道电影异步电影电视Y7G132M，roll道电器凯速器系统代号
公称传动比1=28
Planetary gear gear 线速器5号机座二级传动Y电影roll道电影异步电影电影YGAG160L1roll道电视店速器系统代号
5.1.1 Material for cast iron，machine performance应不可以GB5675的HT200。 5.1.2 应时间时时方法。
5.1.3 发发孔包装公差带为H7，在线维粉度Ra值的3.2um；圆柱度与同長度应不lower than GB1184中国7级。
图度孔的中心分分分度应应事表表4的设计。5.1.4
事心分α||tt| |mm
正天头发士
250~80
>80～120
The center line parallelism tolerance of the bearing hole, measured on the span of the two bearings, should not be greater than the requirements in Table 5. Table 5
Bearing span
Parallelness public shame
120~ 180
125~~280
IB/T 5562
5.1. 6. The perpendicularity between the end face and the bearing hole should not be lower than level 8 in GB1184. 5.1.7 The machine body must not leak oil
5.2 Gears, shaft gears and shafts
5.2.1 External gears and shaft gears are made of forgings, and the material is 20CcrMnMo or 20CrMnTi. The tooth part is magnetized and quenched. The depth of the effective hardened layer on the tooth surface of T is (0.12~~0.20)n, (m is the gear module), and there must be no cracks. The internal gears and floating gear sleeves are made of forgings. The material is 42CrMo or 40Cr. Quenched and tempered. The mechanical properties of the material are shown in Table 6. It is allowed to use materials with equivalent or higher mechanical properties. Cast steel is not allowed. Table 6 | |tt||12CrMo
heat treatment
embedded quenching
interval
Twice rate fire
return
carburizing and quenching
quality
quality|| tt||Tempering
100|| tt||.100
540| |tt||505
Machine
909| |tt||735
Mechanical
12||tt ||15
(Nn)/cm
31||tt ||hard
degree
54--62
Headquarters
Standard number
/7Q 12
5.2.2 The material of the shaft is 45 steel .The heat treatment and mechanical properties are shown in Table 6. It is allowed to use materials with equivalent or higher mechanical properties. 5.2.3 The processing dimensions, shape, position tolerance and surface roughness of the gear reference hole, reference end face, should comply with the provisions of Table 7. Table 7
Name| |tt||Weighing
Gear reference hole
Gear base end face
Full size tolerance zone
H?||tt| |Cylinderity
GB1181
Level 6
End runout
GB11846 level
Table south roughness
Shaft gears and shafts and bearings The processing dimensional tolerance zone, shape position tolerance and surface roughness of the matching datum journal and shoulder should comply with the requirements in Table 8.
Table 8
base journal
eyebrow
dimensional tolerance zone|| tt | | m6 | | tt | The shaft extension diameter, the processing size tolerance zone of the shaft shoulder, the shape position tolerance and surface roughness should comply with the provisions of Table 9 5.2.5
Table 9
Name| |tt||Shaft extension window diameter
Shaft extension shoulder
Dimensional tolerance zone
5.2.6 Matching of gears and shafts For the grade of
cylindricity
GB 1184
coaxiality with the bearing journal||tt| |GB1I&46 level
Surface roughness required
JB/T 5562 ---91
The shape and position of the journal and shoulder where the shaft and gear fit Tolerances and surface roughness shall comply with Table 10. Table 10
The journal that matches the gear
The shoulder that matches the gear
Roundness
GB11846 Level
, the axis degree with the bearing journal
G 1184
Level 6
End face runout
GB 1184 Level 6
The accuracy, shape and position tolerance, and surface roughness of the keyway should comply with the requirements of Table 11. 5.2.8
Table 11
Keyway width tolerance zone
Keyway width Relative axis symmetry
not less than GB11849 level
surface roughness
surface roughness
side: bottom zero
5.2.9 The deviation of the top circle diameter of gears and shaft gears is selected according to Table 12, and the surface roughness Rα value is 12.5m. If the top circle is used for grinding gears to position the top circle radial runout, it should comply with the requirements of Table 13, and the surface roughness Ra value is 1.6 Um. Table 12
Gear indexing point diameter
Gear top circle diameter deviation
Gear indexing circle diameter/mm||tt ||50
radial runout of tooth tip cylinder positioning surface/um
250~80
Table 13||tt| |125
>80～120
120~180
2180~--239|| tt | | 72 | The accuracy of the external gears and shaft gears is 6JE.GB10095. The roughness Ra value of the tooth working surface is 1.6utm. The accuracy of the internal gears and movable gear sleeves (including external teeth and internal teeth) is 8-7-7JLGB10095, and the teeth are 1. The surface roughness Rα value is 3.2 μm. 5.2.11 The combination of inspection items for gears and shaft gears should comply with the requirements of GB10095. The preferred combinations are shown in Table 14. The allowable errors, deviations, and tolerances of each inspection item should comply with the requirements of GB10095.
Inspection group
Accuracy level
1st tolerance group
F(Fk)|| tt||F and Fw
or F\ and F
1st tolerance group
or with
th tolerance group||tt| |F | Gear system
Contact spots
5.3 Planet carrier
JB/T 5562—91
5.3.1 material is The mechanical properties of QT600-3 should not be lower than the specified value of JB/ZQ4302. Materials with equivalent or higher mechanical properties are allowed, and the heat treatment hardness is 190~~270HB 5.3.2. Mechanical processing requirements are in accordance with JB1799. 5.4 Assembly
5.4.1 The inner ring of the bearing must be close to the shaft shoulder or distance ring, and it must be checked with a 0.05mm feeler gauge without obstruction. 5.4.2 The minimum clearance jmn of the gear transmission should comply with the requirements of Table 15. Table 15
center distance
jn nuin
≥80~125
125~~180
5.4.3 Tooth surface contact spots (contact rate) shall not be less than 50% by height and not less than 80% by length . The area for shape modification and edge repair does not include the human contact area. It is allowed to inspect contact spots under rated load. 5.4.4 The unprocessed inner surfaces of the machine body and other parts are painted with cream-colored oil-resistant paint, and the outer surfaces are spray-painted. 5.4.5 The cleanliness of the inner cavity of the reducer should not be lower than level E of the general reducer evaluation parameters specified in GB11368. Inspection methods should comply with the relevant provisions of this standard.
5.5 Reducer Lubrication
5.5.1 Reducer Gear Lubrication and Cooling
5.5.1.1YZI) series are lubricated with calcium-based grease. YGI., YZL, YGX, and YZX series generally use medium extreme pressure gear oil N220 or NV320 for diffuse oil lubrication. The oil immersion depth is 2~~2.5 tooth heights at the top of the high-speed large gear or the internal ring gear of the planetary transmission. For occasions where the ambient temperature is high, circulating oil lubrication can also be used, with oil entering through the ventilation cover and oil returning through the oil drain hole. 5.5.1.2 New reducers that use oil pool flood oil lubrication must be replaced with new oil after 15 to 20 days of operation; under normal circumstances, the oil should be changed once every 5 to 6 months.
5.5.2 The lubrication method of reducer bearings is the same as the lubrication of lubricating oil and gears. 5.5.3 The reducer gear lubricating oil must not penetrate into the motor. 5.6 Testing and Acceptance
d.|| tt||e.
The test is carried out according to the regulations of ZBJ19005.
Only the roller motor reducer that meets this standard can be accepted. Items that must be inspected during acceptance: gear tooth surface hardness;
gear accuracy;
gear tooth surface contact rate;
tooth side clearance, bearing clearance;
cleanliness;
The test passed.
, packaging, transportation, storage
Coat the outer surface of the shaft extension and key with anti-rust grease, and wrap the binding hole tightly with plastic film. 5.7.1
5.7.2 Apply lubricating grease to the gears, shafts, planet carriers and bearings in the body. 5.7.3 Packaging and transportation should comply with the regulations of JB2759 and GB191. Moisture-proof and waterproof measures must be taken for the motor. 5.7.4 Random documents such as instructions, certificates of conformity, packing lists, etc. should be sealed in plastic bags and placed in the packaging box: 110
Carrying capacity of the motor reducer
JB/T 5562--91
Appendix A
Carrying capacity and selection of motor reducer
(Supplement)
Motor reducer The carrying capacity is shown in Table A1. Table A1
Electricity
YZD112M,07! YZG112M.
YZD132M,10YZG132M,||tt| |YZD132M210/YZG132M2
machine
3||tt| |YGL132M,17|YGAG132M
YGI.132M,17YGAG132M
YGL. 1601..27YGAG160L1
YGI.180L,27YGAG180L..
YZI.132M17
Y21.132M217
YZI.160M,27|| tt||YZL160M227
YZD112M,07
YZD132M 10l
YZD132M210
YZG160ML
YZG160Mz
electricity
Incentive rate| |tt||Model
YZG112M
YZG132M,
YZG132M
12.2|| tt||3.7
YGL132M,17YGAG132M
YGL132M.17/YGAG132M22.2
YGI.1601.127 YGAG160L.I
YGI.1801.127 YGAG1801..
YZ1.132M,17
YZL132M217
YZL160M127
YZL160M.27
YZG132M
YZG132M2
YZG160M,
YZG160M2
915||tt ||830
Torque
Rated starting
23.15731.0
908| |tt||915
machine
112|280
23.1| |tt||57
Torque
N?m||tt| |25.7
Less
Nominal transmission ratio:
Output torque calculated based on motor torque/(N ·m) Mt
29.3||tt| |87.6
37.4100.8
88.2||tt| |66.5
81,2||tt| |113.4
73.9184.3||tt| |36.7
Mc||tt| |80.3
46.81126.0
126.3315.8
225.6101.5253.8112. 8282.0
368.5168.4
100.11250.0
定加生
MH|| tt||M.
15,537,936. 2
908| |tt||3.7
38.|| tt||19.5
112||tt| |150
1210.6526.4
224.1101.0
285-||tt ||2.8
43.4107.2
128.83| |tt||321.5143.
公称传动比：
.589.6
125.71313.
357.2160.2
3.55||tt ||按电视转矩设计的性车载矩/（N·m）Mr
62.1|| tt||Me
103.5|258.0
45.8112.8
51.3126 .3
69.8172.4
116.4290.3
198.4||tt| |73.7
157.9394,8177.7
658.0294.8
2| |tt||54.3
225.6101.3
93.6| |tt||4
444. 2|200. 21500. 6|225. 6
736.9331.6
829.1373.7 934.4421.11052.8
150.068.4168.8
392.2||tt ||114.0284.3
176.8440.4
190.286. 5
1145.0|360.9
253.91634.0)
146.8200.3
500.1|225.3
224.5560.2
286.1714.4
103.5|258.0
45.8112.8
51.3126.3
176.3||tt ||MT
69.8172.4
116.4290.3
142.1| |tt||M
157.9394,8177.7
352.5| |tt||658.0294.8
225.6101.3
160.2||tt| |223.6
444 . 2|200. 21500. 6|225. 6
736.9331.6
829.1373.7 934.4421.11052.8
150.068.4168.8
392.2||tt ||114.0284.3
176.8440.4
190.286. 5
1145.0|360.9
253.91634.0)
146.8200.3
500.1|225.3
224.5560.2
286.1714.4
103.5|258.0
45.8112.8
51.3126.3
176.3||tt ||MT
69.8172.4
116.4290.3
142.1| |tt||M
157.9394,8177.7
352.5| |tt||658.0294.8
225.6101.3
160.2||tt| |223.6
444 . 2|200. 21500. 6|225. 6
736.9331.6
829.1373.7 934.4421.11052.8
150.068.4168.8
392.2||tt ||114.0284.3
176.8440.4
190.286. 5
1145.0|360.9
253.91634.0)
146.8200.3
500.1|225.3
224.5560.2
286.1714.4
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.