JB/T 4712-1992 saddle bearing

This standard specifies the structural shape, series parameter dimensions, allowable load, materials and manufacturing, inspection, acceptance and installation technical requirements of saddle bearings. This standard applies to saddle supports for steel horizontal vessels supported by double pivot points. The structural type and structural dimensions of horizontal vessel saddle supports with multi-fulcrum supports can also be used with reference to this standard. JB/T 4712-1992 saddle bearing JB/T4712-1992 standard download and decompression password: www.bzxz.net

Industry Standards of the People's Republic of China
JB/T 4712-92
Saddle Bearing
Released on 1992-07-16
Ministry of Mechanical and Electronic Industry of the People's Republic of China Ministry of Chemical Industry of the Republic
Ministry of Labor of the People's Republic of China
Sinopec Petrochemical Corporation
Implemented on 1992-12-01
Released
2| |tt||3
Theme content and scope of application
Quoted standards
Type characteristics
Series parameters and dimensions
Materials
Mark·
Manufacturing requirements
8 Selection instructions
Item||tt| |Appendix A Sliding saddle bolt hole length (supplement) Appendix B
Allowable load of the saddle exceeding the standard height (supplement) Appendix C
Saddle base pad dimensions (reference)| |tt||times
Theme content and scope of application
Industry Standard of the People's Republic of China
Saddle Bearing
JB/T4712-92
This standard specifies the structural type and series of saddle bearings Parameter dimensions, allowable loads, materials and technical requirements for manufacturing, inspection, acceptance and installation,
This standard is applicable to saddle supports for steel horizontal vessels supported by double pivot points. The structural type and structural dimensions of multi-support horizontal vessel saddle supports can also be used with reference to this standard. 2 Reference standards
Steel pressure vessels
Basic form and size of weld grooves for gas welding, manual arc welding and gas shielded welding GB985
GB1804 Tolerances and Limit deviations for dimensions without tolerances GBJ17
Steel structure design specifications
Type characteristics
Saddle bearings are divided into light (code A) and heavy ( Code B) Two types. Heavy-duty saddles are divided into five models according to the wrapping angle, production method and attached backing plate: BI with a wrapping angle of 120℃, welded and with a backing plate; BⅡ with a wrapping angle of 150C, welded and with a backing plate; BⅢ with a wrapping angle of 120C , welded, without backing plate; BIV - corner wrapped at 120°C, bent, with backing plate; BV - corner wrapped at 120°C, bent, without backing plate. The structural characteristics of various types of saddles are shown in Table 1. Ministry of Mechanical and Electronic Industry
Ministry of Chemical Industry
Motion
Ministry
China Petrochemical Corporation
-3||tt ||Approved on 1992-07-13
1992-12-01 Shijian
Applicable nominal diameter
1000~2000
2100~4900
159~426
300~450
500~900
1000~2000|| tt||2100~4000
1500~2000
2100~4000
159~426
300~450
500~900||tt| |159~426
300~450
500~900
159~426
300~450
500~900
JB /T4712-92
Table 1
String characteristics
120 corner wrapping, welding, four ribs, with backing plate
120 corner wrapping, welding, six Ribs, with backing plate
120 corner wrapping, welded ribs, single ribs, with backing plates
120·Angle wrapping, welded, double ribs, with backing plates120·Angle wrapping, welding, Four ribs, with backing plate 120· corner wrapping, welded, six ribs, with backing plate 150· corner wrapping, welded, four ribs, with backing plate 150 corner wrapping, welded, six ribs, with backing plate ||tt ||120" corner wrap,
welded, single rib, without guard plate
120" corner wrap, welded,
double rib,
without backing plate
120" corner wrap,
120 corner wrap,
Lee system,
Bend system,
Single rib,
With pad Board
Double rib,
With backing plate
120" corner,
Bent,
Single rib, without backing plate||tt ||Without backing plate
Exaggerated system,
Double strategy,
120 corner angle,
The saddle is divided into fixed type (code F) and sliding type (code F) S) Two installation forms of support dimensions
(see table)
Table 2
Table 3
Table 4www.bzxz.net
Table 5||tt| |Table 6
Table 7
Table 8
Table 9
Table 10
Table 4
Table 5
Table 6
Table 4
Table 5
Table 6
Table 4
Table 5
Table 6
4 Series parameters and dimensions
4·1 light (type A) saddle bearing
JB/T4712-92
4·1·1DN1000~2000, 120° angle light belt The structure and size of the backing plate support should comply with the 16
10 bolts in the exhaust hole specified in Figure 1 and Table 2
p 24||tt ||With M20 screw grid
F type
Picture
S type
JB/T4712-92
6|| tt||0
(a)| |tt||0
osc||tt ||Batch
0| |tt||0
000||tt ||Board
Bottom
Follow break
5||tt ||1
0061||tt| |0081
JB /T4712-92
DN2100～4000, 120° angle light-weight padded support structure and dimensions should comply with the requirements in Figure 2 and Table 3, the exhaust hole is electrically 16
F type||tt| |Picture 2
With 0 bolt
S type
JB/T4712-92||tt| |6v
Infant
0||tt| |W
00b|| tt||pad
board||tt| |SEE
STRONG
082|| tt||bo
Butterfly quilt
0||tt ||96
8| |tt||4·2 heavy-duty (B type) digital bearing
JB/T 4712-92
4·2·1DN159～426, 120° angle heavy-duty with pad or without The structure and dimensions of the backing plate saddle bearing shall comply with the requirements in Figure 3 and Table 4.
Welded
Exhaust hole in 8
|tt||F type
2-Φ20
M6 screw wheel
Picture 3
16 × 45 *
16x45°
20×45*
S type
-p| |tt||With 10 bolts
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.