JB/T 9110-1999 Three-sided book trimmer

JB/T 9110-1999 This standard is a revision of ZB J87 003-88 "Three-sided book trimmer". During the revision, technical content and editorial changes were made in accordance with relevant regulations. This standard specifies the classification, requirements, test methods, inspection rules, marking and packaging of three-sided book trimmers. This standard is applicable to three-sided book trimmers for cutting books. This standard was first issued on June 12, 1988. JB/T 9110-1999 Three-sided book trimmer JB/T9110-1999 standard download decompression password: www.bzxz.net

ICS 37. 100. 10
Machinery Industry Standard of the People's Republic of China
JB/T9110—1999
Three-knife trimmer
Published on July 12, 1999
National Bureau of Machinery Industry
Implemented on January 1, 2000
JB.T9110-1999
This standard is a revision of ZBJ87003-8B Three-knife trimmer. Compared with ZBJ87003—8B, this standard has been modified as follows: the basic number of bases, cutting accuracy, trial running and other indicators in the original standard have been appropriately adjusted, and some important supplements have been made to the requirements for the three-knife trimmer.
This standard replaces ZB187003-88 from the date of implementation. Appendix A of this standard is the appendix of the standard, which is proposed and managed by the National Printing Machinery Standardization Technical Committee. The origin of this standard is: Shandong Province Yichenfan Machinery Factory. The participating units of this standard are: Shanghai Ziguang Machinery Co., Ltd., Shanghai Ziming Machinery Co., Ltd., and the main drafters of this standard are: Fu Zhenglin and Zheng Wenli. This standard was first issued on June 12, 1988. 1 Scope
Machinery Industry Standard of the People's Republic of China
Three-sided book trimmer
Threc-knife trimmer
This standard specifies the classification of three-sided book trimmers: requirements, test methods, inspection rules, marking and packaging. This standard applies to the cutting side of the book trimmer: 2 Reference standards
JA/T9110-1999
7B[8700388
The provisions contained in the following standards are considered to be the text of this standard through reference in this standard: The original version of this standard and the versions shown are all valid. The relevant standard department will revise it. The parties using this standard may also discuss the possibility of using the latest version of the following standards: GB191-195G
GB:T 5226.1--1998
GB/ .1--19
GB/ 13306-11
GB/T 13384--1J02
GB/T14436-1993
B/3090-1999
3 Classification
3.1 Model
Packing diagram material
I. Mechanical and electrical equipment Part 1: General technical conditions for the use of products in general terms
Technical specifications for packaging of mechanical and electrical products
II. General rules for product delivery
Manufacture of machine models and product models! Automatic type - automatic input of products to be cut: b) Semi-automatic type - hand-held T picker for cutting products. 3.2 Basic parameters according to the table [standard, table
basic parameters
maximum cutting height
maximum cutting selection
working surface and pressure
pressure
State Machinery Industry Bureau 1999-07-12 batch
automatic type
automatic type
max: 260=380 Www.bzxZ.net
zoin: 92-126
750-46
2000-01-01 actual
JH9110-1999
3.3 The product model name should conform to the black music of B/T339, 4.． Requirements.
4.1 A book marking machine shall comply with the provisions of this standard and be manufactured according to the mesh sample and technical documents approved by the specified light pressure. 4.2 Cutting and drawing
d. 2.1 The deviation of each cutting advance shall not exceed 0.5mm 4.2.2 The parallelism of the edges shall be n.151100mm: 4.2.3 The straightness tolerance of adjacent cutting edges shall be n.10/100mm 4.2.4 Each bearing surface shall be flat and polished
4.3 The machine shall run in a balanced manner and the transmission shall be normal. The operating mechanism shall be accurate without jamming and spontaneous movement. 4.4 The channel sound
is not commercial, and the dynamic type is higher than (
4.5 The temperature rise of the bearing T is greater than 20T|| tt||4.6 The oil circuit of the lubrication system is unobstructed and can be operated without oil condensation. 47 When the machine is started, the electric expansion system works sensitively, safely and reliably. 4.8 The protection unit must be equipped with a connecting device. All safety protection and insurance devices must ensure safety and reliability during the operation of the machine. 4.9 Electrical safety must be guaranteed. The resistance between the external protection conductor and any bare conductor of the electrical equipment and the machine and the casing is not more than 0.152:4..3 The insulation value between the short-circuited power supply circuit and the protection circuit (including the machine base conductor) shall not be less than +1M4.93 All equipment must withstand the withstand voltage test and the test voltage is 1500V (50Hz). There should be no breakdown or flash phenomenon. 4 .1 Appearance
4.10.1 The exposed surface shall not have defects such as corrosion, scratches, etc. 4.10.2 The exposed surface shall not have defects such as pores, bulges, and depressions that damage the appearance. 4.10.3 The gas line, gas line and oil line pipelines shall be arranged in a uniform manner. 14 The whole surface shall be flat and smooth, with consistent color and luster, and no obvious protrusions, no sticking and sandpaper marks, no obvious drying and peeling, etc. 4.11 Product specifications:
Let || Three-sided cutting machine host:
b> Necessary auxiliary equipment:
c) Operation and maintenance tools;
t Necessary accessories and spare parts.
Test method
5.1 Idle running test
The idle running test is to run continuously at rated speed for not less than 120m, and run continuously at rated cutting speed for not less than 3m. The idle running test is to be in compliance with the provisions of 4.3, 4.6-4.8. 5.2 Safety performance test
5.2.1 According to the provisions of 20.2 in GB/T 5326.1-1996, the result shall comply with the provisions of 4.51: 2
JB/T 9-[9
5.2.2 According to the provisions of 2n.! in GB/T 522.1-1996, the measured insulation resistance shall comply with the provisions of 4.9.2: 5.2. 3 According to the provisions of 20.1 in GB 5226.11996, its bed strength shall meet the provisions of 4.9.3: 5.3 Hot scratch test
5.3.1 Test conditions shall be determined according to Table 2.
Table 2 Test conditions
Carry out cutting product cost method
Cutting time
Cutting height
Cutting speed
Use 2m paper, the specified book back should be flat, solid, no foaming, book thickness 8-20mm147×2(0 32 For the semi-automatic type, the rated cutting intensity of B5% is 5.3. According to the provisions of 5.3.1, cutting is carried out, and the cutting quality is checked according to the method in the appendix (the appendix of the standard), and the cutting accuracy is improved by random rotation. The cutting accuracy meets the requirements of 4.2. If the manufacturer has the conditions, the machine noise is measured by ordinary sound level. The height of the measuring point is (machine height + 1) / 2]. The four measuring points are 1m from the symmetrical center line of the machine. The machine noise is the calculated average of the sound values ​​of the four measuring points. The point meets the requirements of 4.4. 5.5 After the rotation test, the bearing temperature is measured with a point thermometer, and the temperature rise is calculated to meet the requirements of 5. 5. (Under static conditions, the ground pressure is measured with a force measuring device, which shall meet the relevant requirements of Table 1. 5. Visually inspect the appearance of the machine, which shall meet the requirements of 4.10. 5.Monthly visual inspection of the product supply range should comply with the provisions of 4.1, 6. Inspection rules
6.! 6.1.1 Each product must be inspected by the manufacturer's quality inspection department and be accompanied by a product certificate before it can leave the factory. 2 Each product shall be inspected in accordance with 5.1, 5.7, and 3.8. If one item fails, the product is a non-conforming product. 6.1.3 10% (no less than two units) of each batch of products shall be re-inspected in accordance with 5.3. If one or more items of the products fail, they shall be re-inspected. If there are still unqualified products, the products shall be inspected one by one. 6.2 Type test
6.2.1 Type test shall be conducted in any of the following situations: a) Trial production of new products or old products b) After formal production, if there are major changes in private materials and processes that may affect product performance: 3 years after the product is put into production and then resumed. 6.2.Type 2 test equipment should be inspected according to all items of this standard. 7 Marking and packaging
7, [Integrate product certification and fix the label in a conspicuous position. The label size should comply with the provisions of GBT13380%. Contents include: a: Name;
JBT9110-1999
h! Product model, service name, product technical standard sales number:) Main cost efficiency:
d Export and import contract number or previous period
7.? Before product packaging, the outer surface of spare parts and accessories should be coated with anti-rust agent. 7.3 Product packaging should comply with the provisions of B.T13384. .4 The outside of the package box should be marked with the manufacturer's name, receiving address, product model, name, package serial number, code, weight ...
Dimensions of each adjacent edge
Parallelism error of the adjacent cutting edge
Verticality test of the adjacent cutting edge
JB/T9110-199
Engraving A
(Appendix of the standard)
Testing method of finished cutting products
Testing method
Take the upper, middle and lower books, check
the basic size difference of the actual scale
as the center error
Take the upper, middle and lower books, measure according to the circumference
, and calculate the parallelism error of each book according to the following formula:
100(α,-a,)
: In the formula: -. 2.
Take the bar, lower the base, and indicate the inner position, and calculate
the verticality error [,
V=LODA
Where:! , 2.….:
caliper
group center
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.