HG/T 2353.3-1992 Test method for the dirt holding capacity of filter elements for magnetic slurry filtration

HG/T 2353.3-1992 Test method for the dirt holding capacity of filter elements for magnetic slurry filtration HG/T2353.3-1992 Standard download decompression password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
Filter element for magnetic slurry filtration
Test method for dirt holding capacity
Subject content and scope of application
HG/T2353.3-92wwW.bzxz.Net
This standard specifies the test method for dirt holding capacity of filter elements for magnetic slurry filtration. This standard is applicable to filter elements for magnetic slurry filtration in the magnetic recording industry, and is also applicable to filter elements for other liquid filtration. 2 Terms
2.1 Dirt holding capacity
The amount of impurities contained by the filter element during its service life (when the pressure drop reaches the rated value), expressed in grams. 2.2 Apparent dirt holding capacity
Continuously add test powder to the test system, and the total amount of test powder added when the pressure drop reaches the rated value. 3 Method summary
When the test liquid passes through the filter element at the rated flow rate, intermittently add test powder to the test liquid until the pressure drop of the filter element reaches the specified value and the test is stopped. The cumulative amount of test powder added is counted and used to represent the dirt holding capacity of the filter element. 4 Test device and test materials
4.1 Test device
The filter element dirt holding capacity test device is shown in the figure below, 6
Sketch of filter element dirt holding capacity test device
1-Test gear: 2 pump; 3 cut-off: 4 filter; 5-pressure differential gauge: 6-flow meter: 7 powder adding system Ministry of Chemical Industry of the People's Republic of China 1992-07-20 approved standard exchange dial network wm.b2s0B0ccm various standard industry data free download 1993-03-01 implementation
HG/T2353.3-92
4.1.1 Storage tank: The bottom is 60°~90° conical and equipped with a stirrer, and the return pipe is in a jet shape. 4.1.2 Flow meter: The accuracy is 1.5 level.
4.1.3 Pressure gauge: The accuracy is 0.4 level.
4.2 Test materials
4.2.1 Test liquid: drinking water or HY-10 aviation hydraulic oil, 4.2.2 Test powder: ACFTD test powder or other equivalent test fine powder, 5 Test procedure
5.1 Cleaning test system
Inject the test liquid into the tank and use a non-tested filter element with a nominal accuracy of 5um to purify the system for 30 minutes. 5.2 Test
5.2.1 Install the tested filter element into the filter, 5.2.2 Start the pump and adjust the shut-off valve so that the test liquid can be circulated and filtered through the filter element at a specified flow rate. 5.2.3 Add the test powder into the test tank at a rate of 5g each time, and make it into a paste. When the filter inlet and outlet pressure drop is close to 80% of the rated value, change the amount added each time to 1g. When the filter inlet and outlet pressure drop reaches the rated pressure value, stop the test. 6 Calculation of pollutant holding capacity
Calculate the cumulative amount of test powder added from the test record sheet. This number is the apparent dirt holding capacity of the filter element for the test powder. Additional notes:
This standard was proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China. This standard is managed by the Magnetic Recording Material Standardization Technical Management Unit of the Ministry of Chemical Industry. This standard was jointly drafted by the Tenth Design Institute of the Ministry of Machinery and Electronics Industry, the 116th Factory of the Ministry of Aerospace Industry, and the Shanghai Xinjing Filtration Equipment Factory.
The main drafter of this standard is Gao Yangzhao.
Standard loss network axw.bzta.con Free download of various standard industry materials
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.