JB/T 10236-2001 Rolling bearings - Tapered roller bearings - Vibration (velocity) technical requirements

JB/T 10236—2001 This standard specifies the vibration (velocity) technical conditions for finished tapered roller bearings with nominal inner diameters of 15 to 60 mm and 3020, 32200, 30300 and 32300 series in GB/T 297 "Rolling bearings, tapered roller bearings, dimensions". The vibration (velocity) group V specified in this standard is the basic requirement for grade 0 bearings and is applicable to production inspections by bearing manufacturers; groups V1, V2 and V3 are applicable to bearings for which users require control of vibration (velocity) levels and are provided for inspection by manufacturers and acceptance by users. This standard was first issued in May 2001. JB/T 10236-2001 Technical conditions for vibration (velocity) of rolling bearings, tapered roller bearings JB/T10236-2001 Standard download decompression password: www.bzxz.net

ICS21.100.20
Machinery Industry Standard of the People's Republic of China
JB/T 10236—2001
Rolling bearings
Tapered roller bearings
Vibration (velocity) technical conditions
Rolling bearings--Specifications of vibration (velocity) for tapered roller bearings2001-05-23 Issued
China Machinery Industry Federation
2001-10-01 Implementation
JB/T10236—2001
This standard is formulated for the first time.
This standard is proposed and managed by the National Technical Committee for Standardization of Rolling Bearings. The drafting units of this standard are: Hangzhou Bearing Test and Research Center, Hangzhou Zhaofeng Bearing Co., Ltd. The main drafters of this standard are: Kang Naizheng, Xie Ming, Shen Yuntong, Chen Fanghua. 1 Specifications of vibration (velocity) for tapered roller bearings JB/T 10236-2001 This standard specifies the vibration (velocity) specifications for finished tapered roller bearings with dimensions in accordance with the 30200, 32200, 30300 and 32300 series in GB/T297 and a nominal inner diameter of 15 to 60 mm. The vibration (velocity) group V specified in this standard is the basic requirement for grade 0 bearings and is applicable to production inspections of bearing manufacturers. The V1, V2 and V3 groups are applicable to bearings that require control of vibration (velocity) levels by users and are provided for inspection by manufacturers and acceptance by users. 2 Referenced standards The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard was published, the versions shown were all valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T 297--1994
GB/T 2828--1987
JB/T5313--2001
3 Definitions and units
Rolling bearings Tapered roller bearings Dimensions Batch inspection Count sampling procedures and sampling tables (applicable to continuous batch inspection) Rolling bearing vibration (speed) measurement method This standard adopts the definitions and units given in JB/T5313. 4 Technical requirements
The vibration (speed) value measured by a single bearing shall not exceed the provisions of Table 1. 5 Measurement method
The vibration (speed) measurement method of tapered roller bearings shall be in accordance with the provisions of JB/T5313. 6 Inspection rulesbzxz.net
6.1 When the vibration (speed) value of any frequency band of a single bearing is greater than the corresponding level specified in Table 1, the bearing is a defective product. 6.2 When sampling and inspecting the vibration (speed) of a batch of bearings, according to GB/T2828, use the general inspection level II, adopt the normal inspection one-time sampling plan, and the qualified quality level AQL value is 2.5. China Machinery Industry Federation approved on May 23, 2001, implemented on October 1, 2001
Bearing nominal
Inner diameter d
1) is not indicated in the bearing code.
JB/T 10236—2001
Single bearing vibration (speed) limit
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.