JB/T 8296.1-1999 Open wheelset for narrow-gauge mining vehicles

JB/T 8296.1-1999 This standard is a revision of JB/T 8296.1-95 "Open wheelsets for narrow gauge vehicles in mines". The bearing models in the basic parameters of open wheelsets were cancelled during the revision, and other major technical contents remained unchanged. This standard specifies the basic parameters, dimensions and technical requirements of open wheelsets for narrow gauge vehicles in mines. This standard is mainly applicable to narrow gauge vehicles used in mines whose wheel treads comply with Type A in GB/T 4695-1984 "Shape and dimensions of wheel treads for narrow gauge vehicles". This standard was first issued as GB 4786.1-84 in November 1984 and was adjusted to JB/T 8296.1-95 in April 1996. JB/T 8296.1-1999 Open wheelsets for narrow gauge vehicles in mines JB/T8296.1-1999 Standard download decompression password: www.bzxz.net

[CS73.100.4
Machinery Industry Standard of the People's Republic of China
JB/T8296.1—1999
Narrow gauge mine car
Open type wheel assembly
Narrow gauge mine car Open type wheel assembly1999-06-28 Issued
State Machinery Industry Bureau
2000-01-01 Implementation
FB8296.1—1999
This standard is the revision of JB.T8296.1-95 Mining narrow gauge vehicles: open type wheels, canceling the bearing models in the standard. Other major technical contents remain unchanged. This standard will replace JB.T8296.1—95 from the date of implementation. This standard is proposed and coordinated by the National Mining Machinery Standardization Technical Committee. The drafting units of this standard are Luoyang Machinery Research Institute, Beijing Hoisting and Transport Machinery Research Institute. The main drafters of this standard are Guo Ming, Yang Xianli, Huang Jialin, Li Xulun, and Zhou Yunxiang. This standard was first issued as GB4786.1-84 in November 1984 and was adjusted to JB/T8296.195 in April 1996.
Machinery Industry Standard of the People's Republic of China
Nurruw gauge mine car Open lype wheel assemhlyThis standard specifies the basic parameters, dimensions and technical requirements of open wheelsets for standard gauge mine vehicles: JB/T8296.1-1999
JH[8296 1-95
This standard is applicable to narrow gauge vehicles for mine vehicles with wheel treads conforming to Type A specified in GB/T4695. 2 Referenced Standards
All the provisions of the above standards are incorporated into the standard by citing them in this standard. When the standard is published, the versions shown are valid. All standards will be revised. All parties using this standard should explore the possibility of using the latest version of the following standards. i T4695-1984 Wheel tread shape and size of track-crossing locomotives and vehicles 3 Basic numbers and dimensions
3.1 The basic number of open wheelsets shall comply with the provisions of Figure 1 and Table 1. Fresh film
Push type
Guohao Machinery Industry High 19-06-28 approved
20001-implemented
L,3062
1,3072bzxz.net
Total mine car
JB/T9296.1—1999
Note: The total sensitivity of the mine car (self-release and shielding! Refers to the total weight of the axle car: 3.2 Model mark:
New distance: 6 means 600mm
7 means T62m
9 means 900 cut m
Wheel diameter: m
A type wheelset
Marking example:
Rail The heavy-duty wheelset with a wheel pitch of 600mm and a wheel diameter of 300mm is marked as: open wheelset L,3062
4 Technical requirements
4.1 The open wheelset shall comply with the requirements of this standard and shall be manufactured in accordance with the drawings and technical documents approved by the prescribed procedures. 4.2 The open wheelset shall be selected according to the total length and heat distance of the furnace car. 4.3 Before the wheelset is assembled, the debris and blockages shall be removed and the parts shall be cleaned. 4.4 When installing the bearing, it shall be pressed in a non-impact load-bearing method and shall not be directly impacted.
4.5 When installing the bearing, it shall be adjusted to the correct position, the wheel shall rotate freely, and a lubricant shall be filled that occupies 65%-80% of the wheel shoe oil storage cavity.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.