JB/T 3103.1-1999 Saw blade toothing machine accuracy

JB/T 3103.1-1999 This standard is a revision of JB 3103-82 "Precision of saw blade toothing machines". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies the geometric accuracy and inspection methods of saw blade toothing machines. This standard is applicable to saw blade toothing machines with a maximum width of punching and shearing woodworking saw blades not exceeding 250mm. This standard was first issued on May 12, 1982. JB/T 3103.1-1999 Precision of saw blade toothing machines JB/T3103.1-1999 Standard download decompression password: www.bzxz.net

ICS79.120.10
Machinery Industry Standard of the People's Republic of China
JB/T3103.1-1999
Saw Blade Gearing Machine
Published on 1999-05-14
National Bureau of Machinery Industry
Implemented on 2000-01-01
JB/T3103.1—1999
This standard is a revision of JB310382 "Saw Blade Gearing Machine Accuracy". During the revision, only editorial changes were made according to relevant regulations, and the technical content has not changed
This standard replaces JB3103—82 from the date of implementation. This standard was proposed by the National Technical Committee for Standardization of Woodworking Machine Tools and Cutting Tools. This standard is under the jurisdiction of Fuzhou Woodworking Machine Tool Research Institute. The responsible drafting unit of this standard: Shenyang Woodworking Machine Tool Factory. This standard was first issued on May 12, 1982. 1
Machinery Industry Standard of the People's Republic of China
Accuracy of saw blade toothing machines
This standard specifies the geometric accuracy and inspection methods of saw blade toothing machines. JB/T3103.1-1999
Replaces JB310B82
This standard applies to saw blade toothing machines (hereinafter referred to as toothing machines) with a maximum width of punching and shearing woodworking saw blades not exceeding 250mm. Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. JB/T4171-1999 General Rules for Precision Inspection of Woodworking Machine Tools 3 General Requirements
3.1 When using this standard, refer to JB/T4171. 3.2 Refer to 3.1 in JB/T4171-1999 to adjust the installation level of the machine tool. Place the level in the center of the workbench. The level reading should not exceed 0.10/1000.
3.3 The order of precision inspection items listed in this standard does not represent the actual inspection order. In order to improve efficiency, inspections can be carried out in any order. 3.4 When the specified length cannot be measured, the tolerance can be converted according to the measurable length according to 3.2.1.1 in JB/T4171-1999, and the minimum conversion value is 0.01mm.
4 Geometric Precision
Geometric precision inspection shall be in accordance with the provisions of Table 1.
National Machinery Industry Bureau1999-05-14Approved Inspection Items
Lower Die
Straightness of the Working Surface on a Length of 100
Table 1 (End)
Blade Ruler
Inspection Method Reference
Related Articles of JB/T4171—1999
4.2.12.2.2
2000-01-01Implementation
JB/T3103.1-19 99
Inspection items
Punch shaft
Line to guide post
Planarity of movement
Guide post shaft
Line to lower die
Verticality of working surface
0.03 in the whole process
Inspection rod end face diameter
80When it is 0.08
Indicator
Inspection rod
Inspection method Refer to
JB/T4171—1999
Relevant provisions
44.2.22.3.2
Insert the inspection rod into the guide column hole so that the end of the inspection rod touches the working surface of the lower die. Then use a feeler gauge to measure the gap between the end of the inspection rod and the working surface of the lower die along the circumferential direction. The maximum measured gap is the verticality
Mechanical Industry Standard
Precision of Saw Blade Gearing Machine
JB/T3103.11 999
Published by the Machinery Standardization Research Institute of the Ministry of Machinery Industry Printed by the Machinery Standardization Research Institute of the Ministry of Machinery Industry (No. 2 Shouti South Road, Beijing: Postal Code 100044)*bZxz.net
Format 880×1230
X number of characters xXX,XXX
Print sheets X/X
Xth printing in XX month, 19XX
Xth edition in XX month, 19XX
Number of prints 1-XXX
Price XXXXX Yuan
XX-XXX
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.