JB/T 9890-1999 Accuracy test of multi-station movable worktable of modular machine tool

JB/T 9890-1999 This standard is a revision of ZB J58 010-89 "Precision of Multi-station Mobile Tables for Modular Machine Tools". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies the geometric accuracy requirements and inspection methods for multi-station mobile tables (hereinafter referred to as worktables) of modular machine tools. This standard is applicable to the worktables of modular machine tools and their automatic lines. This standard was first issued in 1989. JB/T 9890-1999 Precision inspection of multi-station mobile tables for modular machine tools JB/T9890-1999 Standard download decompression password: www.bzxz.net

1C.S 25. 060.99
Machinery Industry Standard of the People's Republic of China
JB/T 9890-1999
Modular Machine Tools
Multi-station Mobile Workbench
Published on 1999-05-20
State Machinery Industry Bureau
Precision Inspection
2000-01-01 Implementation
JB/9890--1999
Standardization level is based on ZBJ581(89 "Precision of multi-position mobile worktable of modular machine". The technical content of this standard is consistent with ZBJ58010-89, and it has only been re-edited according to relevant regulations. This standard will replace ZDJS801U- from the date of implementation. This standard is proposed by the Technical Committee for Standardization of Metal Cutting Machine Tools. This standard is under the jurisdiction of the Modular Machine Tool Branch of the Jin Guo Jin Liang Machine Tool Standardization Technical Committee. The drafting unit of this standard is: Renlian Modular Machine Tool Research Institute. This standard was first issued in 1089 and is the Machinery Industry Standard of the People's Republic of China. t||Precision inspection of multi-station mobile worktable
JE/TV890-1999
Replaces 15801089
This standard specifies the accuracy requirements and inspection methods of the multi-station mobile worktable (hereinafter referred to as "worktable") of a combined machine. This standard is applicable to the working methods of combined machine tools and their automatic lines. 2 Reference standards
The texts contained in the following standards are not applicable to this standard and are not included in this standard. At the time of publication of this standard, the provisions shown in the standard are effective. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T1742.11998 Machine without inspection, clause 1 Part: Geometry of machine tools without pornography or precision machining 3 Brief description
3.1 The nominal size of the worktable is the sliding width of the corresponding worktable 3.2 When using this standard, the relevant provisions of GB 17421.1 shall apply. 3.3 The order of precision inspection items listed in this standard does not represent the actual inspection order. In order to reduce the installation of inspection tools and facilitate inspection, inspections can be carried out in any order.
3.4 ​​The inspection tools and instruments specified in this standard are of a punching nature: production 4. Any other inspection tools and instruments may be used under the premise of ensuring the inspection quality.
35 In the inspection items using a straight ruler, the two supports of the straight ruler should be in the best support position, that is, the corresponding 5/9 of the length of the ruler to minimize the self-stirring of the flat ruler.
3.6 Place the workbench on the half plate and use a feeler gauge to check the difference between the bottom surface of the slide and the flat plate. For general-grade workbenches, use a 0.04mm feeler gauge, for precision-grade workbenches, use a 0.03mm feeler gauge, and for high-precision workbenches, use a 0.02mm feeler gauge. The insertion length of the feeler gauge shall not exceed 5m. After passing the test, carry out various precision tests for accuracy numbers G1-G5. 3.7 The test of geometric accuracy numbers G6 and G7 is carried out on the test bench. Approved by the State Administration of Industry and Information Technology on May 20, 1999 and implemented on January 1, 2000
JB.T98901999
2'e'Es +E'te's
IB/9890-1999
tra001
910°0
01009100:
0r00910:0
000 1 -
J89890-1999
I'ZE'Z'S
0,91o0
900001009100
JB/I9 890
0091--
2100+200+00
JD/T98901999wwW.bzxz.Net
1009100
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.