JB/T 10042-1999 Cylindrical sand sleeve

JB/T 10042-1999 This standard is a revision of ZB J43 008-89 "Cylindrical Sand Sleeves". During the revision, only editorial changes were made according to relevant regulations, and the main technical content remained unchanged. The dimensions and tolerances of cylindrical sand sleeves in this standard are equivalent to ISO 2421:1972 "Cylindrical Sand Sleeve Marking Dimension Tolerances". This standard specifies the code, marking, dimensions and tolerances, technical requirements and inspection rules of cylindrical sand sleeves. This standard is applicable to cylindrical sand sleeves made of emery cloth and sandpaper. This standard was first issued on the date of year. JB/T 10042-1999 Cylindrical Sand Sleeve JB/T10042-1999 Standard download decompression password: www.bzxz.net

JB/T10042—1999
This standard is a revision of ZBJ43008—89 "Simple Sand Sleeve".
The dimensions and tolerances of the simple sand sleeve in this standard are equivalent to ISO24211972 "Simple Sand Sleeve-Marking-Dimension-Tolerance". This standard is consistent with the technical content of ZBJ43008-89, and has only been re-edited according to relevant regulations, and "Js16" and "Js14\ in Table 1 of the original version have been converted into specific data. This standard replaces ZBJ43008-89 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Abrasives and Grinding Tools. The drafting unit of this standard: Zhengzhou Abrasives and Grinding Research Institute. The main drafter of this standard: Zhang Changwu.
This standard was first issued in March 1989.
Machinery Industry Standard of the People's Republic of China
Cylindrical Sand Sleeve
This standard specifies the code, marking, size and tolerance, technical requirements and inspection rules of simple sand sleeves. This standard applies to cylindrical sand sleeves made of emery cloth and sandpaper. Reference Standards
JB/T 10042—1999
Replaces ZBJ43008—1989
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T2828-1987 Batch inspection counting sampling procedures and sampling tables (applicable to inspection of continuous batches) 3 Simple sand sleeve code
3.1 Simple sand sleeve shape code: S
3.2 Simple sand sleeve product code:
Simple sand cloth sand sleeve SC
Cylindrical sandpaper sand sleeve
4 Marking example
Brown corundum P60\simple sand cloth sand sleeve with inner diameter d-100mm and width l-50mm is marked as: SC 100X50 A P60
Simple sand sleeve size and limit deviation
Simple sand sleeve size code as shown in Figure 1. Figure 1
5.1 Inner diameter size and limit deviation should comply with the provisions of Table 1. Table 1
Limit,
Flat joint
Deviation Spiral joint
Kuohao Machinery Industry Week 1999-05-20 Approved 320
125|160200250
±1.25±1. 45
±0.435±0.50
2000-01-01 Implementation
JB/T 10042—1999
5.2 The width dimension and limit deviation shall comply with the provisions of Table 2. Table 2
Limit deviation
6 Technical requirements
The outer surface of the simple sand sleeve is not allowed to have sand missing. 6.21
The simple sand sleeve is not allowed to have creases, wrinkles and holes. 6.3
The layers of the cylindrical sand sleeve are not allowed to be debonded. ±2
6.4 The gap between the edges of the simple sand sleeve made by the spiral joint method should not be greater than 1mm. 6.5 The cylindrical sand sleeve with an inner diameter of more than 100mm should not be broken when rotating at a speed of 34m/s for 3min without load. 7 Test method
7.1 The inner diameter of the simple sand sleeve is measured with a vernier caliper with a graduation value of 0.05mm, and the width and the gap at the interface are measured with a steel ruler with a graduation value of 0.5mm.
7.26.1, 6.2 and 6.3 are determined by visual inspection. 7.3 After the simple sand sleeve is mounted on a special tensioning device and rotated at a speed of 34m/s on a variable speed rotary test machine for 3 minutes without load, check whether it has any cracks.
8 Inspection rules
The simple sand sleeve shall be inspected according to the items specified in Chapter 5 and Chapter 6 for factory or delivery inspection. 8.2
The inspection of the simple sand sleeve adopts the one-time normal sampling plan specified in GB/T2828. The inspection level and qualified quality level of each inspection item shall comply with the provisions of Table 3.
Inspection items
Inspection level
Qualified quality levelbzxZ.net
6.2 and 6.3
8.3 In the above sampling plan, if the sample size required for each inspection item is different, it shall be drawn out according to the largest sample-one time, and the small sample shall be drawn in advance from the large sample before inspection.
9 Marking and packaging
9.1 The content of the simple abrasive sleeve marking includes:
a) manufacturer name;
b) product name;
c) size specifications;
d) abrasive and particle size number;
e) manufacturing date or production batch number.
The above marking content may not be marked on the product, but it must be marked on the packaging or provided in the form of instructions. 9.2 The packaging should be solid and reliable and comply with the relevant regulations of the transportation department. 321
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.