JB/T 6753.2-1993 Electrical equipment and equipment component tolerances Metal shear parts general tolerances

This standard specifies the general tolerances for metal sheet shears with a thickness of up to 12 mm. JB/T 6753.2-1993 Electrical equipment and equipment component tolerances General tolerances for metal shears JB/T6753.2-1993 Standard download decompression password: www.bzxz.net

Subject content and scope of application
Machinery Industry Standard of the People's Republic of Chinabzxz.net
Equipment structure tolerances of electrical equipment
General tolerances of metal shearing parts
This standard specifies the general tolerances of metal sheet shearing parts with a thickness of up to 12mm. JB/T6753.2—93
This standard applies to shearing parts obtained by shearing and directly obtained by shearing machines in the equipment structure of electrical equipment. It can also be used as a reference for shearing and processing parts of plates, strips, strips and profiles processed by other methods. 2 Reference standards
JB/T6753.1 Equipment structure tolerances of electrical equipment General tolerances of sheet metal parts and structures and their selection rules 3 Terminology
Shearing parts
Blocks, strips or parts obtained by shearing metal sheets can be called shearing parts. 3.2 Shear width
The distance from the cutting edge of the shear blade to the opposite edge is called the shear width (see dimension b in Figure 1). 3.3 Shear length
The length of the side of the shear piece cut by the shear blade is called the shear length (see dimension L in Figure 1). Shear piece
Tolerance grade
The general tolerances of the shear width, shear length straightness and shear verticality are divided into two grades, A and B. According to the different requirements of the shear piece, they can be selected separately or mixed.
Approved by the Ministry of Machinery Industry on August 21, 1993
Implementation on October 1, 1993
JB/T6753.1-93
9.3When necessary, the limit deviation value of the corresponding tolerance grade of this standard can be directly indicated in the drawing. For example: directly marked as 800-1 in the drawing. Additional Notes:
This standard was proposed and managed by Beijing Institute of Electrical Engineering Comprehensive Technology and Economy. This standard was drafted by Tianjin Electric Drive Design Institute, Xuchang Relay Institute, Shenyang Low Voltage Switch Factory, and Shanghai Huatong Switch Factory. Shanghai Electric Complete Plant, Minming Switch Factory, Beijing Second Switch Factory, and Guangzhou Nanyang Electric Factory participated in the drafting of this standard. The main drafters of this standard are Guo Xiaohu, Tian, ​​Cui Guochang, Zhou Guixin, and Wang Aimang. 3
General Tolerance
JB/T6753.293
The general tolerance of shear width is shown in Table 1. The value selection method is in accordance with Article 3.2 of JB/T6753.1. Table 1
Cutting width
>30~120
>120~400
>400~1000
>1000~2000
>2000~4000
For the general tolerance of cutting length straightness, see Table 2. Material
Cutting length
>120~400
>400~1000
>1000~2000
>2000--4000
For the general tolerance of cutting verticality, see Table 3.
Short side length
>120~400
>400~1000
>1000~2000
>2000~4000
Conform to the provisions of Chapter 9 of JB/T6753.1.
Additional remarks:
JB/T 6753.2-93
This standard is proposed and managed by Beijing Institute of Electrical Engineering Comprehensive Technology and Economy. This standard is drafted by Tianjin Electric Drive Design Institute, Xuchang Relay Institute, Shenyang Low Voltage Switch Factory, and Shanghai Huatong Switch Factory. Shanghai Electric Complete Plant, Kunming Switch Factory, Beijing Second Switch Factory, and Guangzhou Nanyang Electric Factory participated in the drafting. The main drafters of this standard are Guo Xiaohu, Cui Guochang, Li Cuihua, Tian, ​​and Zhou Luying.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.