GB/T 5054-1985 Seven-core cables for vehicles and trailers
time:
2024-08-04 22:59:49
- GB/T 5054-1985
- Abolished
Standard ID:
GB/T 5054-1985
Standard Name:
Seven-core cables for vehicles and trailers
Chinese Name:
汽车与挂车的七芯电缆线
Standard category:
National Standard (GB)
-
Date of Release:
1985-03-09 -
Date of Implementation:
1986-02-01 -
Date of Expiration:
2007-08-01
Standard ICS number:
Road vehicle engineering>>Road vehicle equipment>>43.040.10 Electrical and electronic equipmentChina Standard Classification Number:
Vehicles>>Automotive Electronics, Electrical Equipment and Instruments>>T36 Electronics, Electrical Equipment
alternative situation:
Replaced by GB/T 5054.3-2006Procurement status:
≡ISO 4141-78
Review date:
2004-10-14Drafting Organization:
Highway Research Institute, Ministry of TransportFocal point Organization:
National Automobile Standardization Technical CommitteePublishing Department:
National Bureau of StandardsCompetent Authority:
National Development and Reform Commission
Description (Translated English) / downloadSkip to download
Summary:
This standard specifies the specifications of seven-core cables for electrical connectors between vehicles and trailers. This standard applies to 12N, 24N, 12S and 24S electrical connectors. GB/T 5054-1985 Seven-core cables for vehicles and trailers GB/T5054-1985 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
National Standard of the People's Republic of ChinabZxz.net
Seven-core connecting cable of motor vehiclesand towed vehicles
This standard specifies the specifications of seven-core cables used as electrical connectors between motor vehicles and trailers. This standard applies to 12N, 24N, 12S and 24S electrical connectors. This standard is equivalent to the international standard ISO4141--1978 "Road vehicles - seven-core cables". UDC 629.11.013
.5 : 621.315.2
GB 5054—85
ISO 4141-1978
1 The seven-core cable consists of 6 core wires with a cross-sectional area of 1.5mm2 each and 1 common loop core wire with a cross-sectional area of 2.5mm2. 2 The outer sheaths of the seven core wires should have distinctive colors. The colors and corresponding positions are shown in the figure. 3 The outer diameter of the seven-core cable is Φ13.5-2.5mm. Additional Notes:
This standard was proposed by the Ministry of Communications of the People's Republic of China and is under the jurisdiction of the Standardization and Metrology Institute of the Ministry of Communications. This standard was drafted by the Highway Research Institute of the Ministry of Communications. The main drafter of this standard is Wang Lilin.
Published by the National Bureau of Standards on March 9, 1985
Implemented on February 1, 1986
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Seven-core connecting cable of motor vehiclesand towed vehicles
This standard specifies the specifications of seven-core cables used as electrical connectors between motor vehicles and trailers. This standard applies to 12N, 24N, 12S and 24S electrical connectors. This standard is equivalent to the international standard ISO4141--1978 "Road vehicles - seven-core cables". UDC 629.11.013
.5 : 621.315.2
GB 5054—85
ISO 4141-1978
1 The seven-core cable consists of 6 core wires with a cross-sectional area of 1.5mm2 each and 1 common loop core wire with a cross-sectional area of 2.5mm2. 2 The outer sheaths of the seven core wires should have distinctive colors. The colors and corresponding positions are shown in the figure. 3 The outer diameter of the seven-core cable is Φ13.5-2.5mm. Additional Notes:
This standard was proposed by the Ministry of Communications of the People's Republic of China and is under the jurisdiction of the Standardization and Metrology Institute of the Ministry of Communications. This standard was drafted by the Highway Research Institute of the Ministry of Communications. The main drafter of this standard is Wang Lilin.
Published by the National Bureau of Standards on March 9, 1985
Implemented on February 1, 1986
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- SB/T 10523-2009 Rules for wholesale of fishery products
- GB 3300-1991 Test method for deformation of daily-use ceramics
- GB/T 20544-2006 Banking - Procedures for message encipherment (wholesale) - General principles
- JB/T 50147-2000 Measuring instruments for product quality grading Small torsion spring comparator
- JB/T 5811-1991 Test methods and limits for interturn insulation of AC low-voltage motor formed windings
- GB/T 3781.7-1993 Determination of iodine absorption value of acetylene black
- GB/T 2820.9-2002 Reciprocating internal combustion engine driven alternating current generating sets Part 9: Measurement and evaluation of mechanical vibration
- JB/T 7966.8-1999 Die and mold milling cutters Part 8: Conical end mills with Morse taper shank
- GA 441-2003 General Rules for the Coding of Industrial Detonators
- JB/T 3192.2-1999 Accuracy test of spiral bevel gear milling machine
- JB/T 6293-1992 Technical conditions for manual injector calibrator
- HG 3167-1986 Mixing shaft diameter series
- GB/T 2424.24-1995 Environmental test guide for electrical and electronic products - temperature (low temperature, high temperature)/low pressure/vibration (sinusoidal) comprehensive test
- SC/T 1061-2002 Technical specification for breeding of longnose catfish
- GB/T 2588-2000 General rules for calculation of thermal efficiency of equipment
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：bzxznet@163.com