HG/T 2054-1991 Glass-lined equipment clamps

HG/T 2054-1991 Glass-lined equipment clamp HG/T2054-1991 standard download decompression password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
Tang Glass Equipment
Subject Content and Scope of Application
This standard specifies the type, basic parameters, main dimensions and technical requirements of Tang Glass Equipment Clamps. HG/T2054-91
Type A clamps in this standard are applicable to Tang Glass Equipment with a nominal pressure less than or equal to 1.0MPa: Type B clamps are applicable to Tang Glass Equipment with a nominal pressure less than or equal to 0.4MPa, Reference Standard
GB97.1 Flat Washer, Class A
GB2828
GB5679
GB5784
GB6170
JB3965
JB4385
Technical conditions for high-quality carbon structural steel
Batch-by-batch inspection counting sampling procedures and sampling tables (applicable to inspection of continuous batches) Malleable cast iron
Hexagonal head bolts with thin shank, Grade B
Type 1 hexagonal nuts, Grade A and Grade B
Magnetic particle inspection of steel pressure vessels
General technical conditions for free forgings on hammer
ZBG94004 Technical conditions for glass equipment
3 Types, basic parameters and main dimensions
3.1 See Figure 1, Table 1 and Table 3 for type A clamps.
3.2 See Figure 2, Table 2 and Table 3 for type B clamps.
Approved by the Ministry of Chemical Industry of the People's Republic of China on July 6, 1991 and implemented on January 1, 1992bZxz.net
Thread specifications
85~105
85~105
This standard clamp M12 has two clamping distances,
Connection, M12 (card distance 60~
HG/T2054
Applicable to storage
Reference weight
Applicable to manhole with protective ring and hand hole with protective ring flange connection,
Thread specification
85~105
85~105
This standard clip M12 has two card distances,
HG/T2054-91
Card rent 80~
Reference weight
Applicable For connection of manhole with protective ring and hand hole with protective ring (95mm), M12 (card distance 60~80mm) suitable for flange connection of storage container and mixing container tank, position number GB6170 GB5679 GB5679 GB5784 HG/T2054—91 PVC 35 or ZG270-500 KTH350-10 tt||KTH350-10
Q235-A
*Note: Type A clips may be replaced by other materials, but the breaking load value must meet the requirements of Table 4 in the technical requirements. 3.3 Marking
Marking example: Type A clips, bolts are M16, and the distance between clips is 90mm. Marking: Clip AM16-90HG/T2054--91. Technical requirements
4.1 The breaking load of the clip tensile test shall not be less than that specified in Table 4. Table 4
Thread specifications
Type A clip 4.2 The clamps shall be stretched at the average clamp distance (h average
125000
A-type clamp
B-type clamp
A-type clamp
B-type clamp
150000
). A relative elongation of 15% is considered to be broken. 2
4.3 Forged clamps shall be tested according to the requirements of Grade II forgings specified in JB4385 and the hardness test ratio of Grade II forgings. Magnetic particle inspection, qualified according to JB3965 Grade III,
4.4 After each batch of clips is manufactured, refer to the methods and procedures specified in GB2828 and carry out sampling tensile test according to the values ​​in Table 5, Table 5
Batch basket, piece
Tensile test sampling number
1%, and not less than 5 pieces
0.5%, and not less than 10 pieces
Allowed number of unqualified
1. Less than or equal to 10% of the number of samples inspected is qualified; 2. For those greater than 10% of the number of samples inspected and less than or equal to 20%. 1-2 rechecks and random inspections can be conducted. The number of rechecks and random inspections is the same as the sum of the number of random inspections previously conducted. However, the total number of unqualified items shall be less than or equal to 10% of the total number of random inspections to be qualified.
Packaging, transportation and storage
HG/T 2054 --91
5.1 Products shall be shipped in full packages or boxes. Packing lists, product certificates and manufacturer's product sampling inspection tensile test data shall be attached. 5.2 Products shall be stored indoors.
Additional instructions:
This standard was proposed by China National Chemical Equipment Corporation and is under the jurisdiction of the National Glass Equipment Standardization Technical Committee. This standard was drafted by the Shanghai Pharmaceutical Design Institute of the State Drug Administration. The main drafters of this standard are Ye Wenbang, Li Yijun and Hua Qiuyuan. From the date of implementation of this standard, the former Ministry of Chemical Industry's standard HG5-269-79 "Glass Equipment Clips" shall be invalidated. This standard A-type clip is based on the German national standard DIN28152-1979 "Clips for pond glass containers, dimensions and configurations".
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.