QB/T 2507-2001 Composite film bag making machine

This standard specifies the product classification, technical requirements, test methods, inspection rules and markings, operating instructions, packaging, transportation, storage and other requirements of composite film bag making machines. This standard applies to SD8430 series composite film bag making machines with heat-sealable materials as the inner layer (hereinafter referred to as "bag making machines"). QB/T 2507-2001 Composite film bag making machines QB/T2507-2001 Standard download decompression password: www.bzxz.net

Classification No. Y99
Registration No. 9098-2DC
Light Industry Standard of the People's Republic of China
QB/T 2507—2001
Composite Film Bag Making Machine
Published on 2001-07-16
Published by China Light Industry Federation
Implemented on 2001-11-01
QB/T 2537—2001
This standard is revised on the basis of the original light industry professional standard ZBY99040-1989 table SD84304 sealed white dynamic attack machine (this standard was issued by the State Light Industry [1999] No. 112 document and the chemical standard number is Q1/T3692—1999, before the proposal),
4 The standard adopts the technical conditions for the installation of thin film sealed machines of Japan Rock Company AC-CW300 and TOTANI company FD-35V≤3. bzxZ.net
Based on the technical specifications described in this company, the other specifications are added as follows: 1. The total frequency of SD8430 is (30--120) times/min, FD-35V is (50~-200) times/min, the maximum working speed of SDR43 series is (1420) m/m, the total power of FD-35 is 10kw~4kw, and FD-35 is 502k. This standard and the concurrent standard technical content changes: the original SD8430 series of composite film bagging machine 3 single product additions changed to 6SD8430 series composite film bagging machine. From the original GR/T5226 provisions, the new national standard GB/5226.1-1996 provisions of the specific provisions. From the original Q/T3692-1999 metal cutting machine noise sound pressure level of the provisions: changed to the new second series standard B16769--1997. The current state of the state inspection and supervision classification and determination plan. Cancel the GB2894-1988 safety association mark and the relevant documents on quality management and other requirements. This standard is proposed by the General Business Department of the China Light Industry Association. The standard was drafted by the National Light Machinery Standardization Center: Shanghai Light Machinery Equipment (Group) Co., Ltd. Light Industry Machinery Factory. This standard mainly refers to the industry standard Qn/T3692-1599S1>8430 type medium sealed automatic assembly machine issued by the former State Bureau of Light Industry.
-YY KAN KAa-
People's Republic of China Light Industry Standard
Composite Film Bag Making Machine
QB/T2507-2001
Daiqi E/1692-1999
Cloud standard extends the classification, technical requirements, test methods, inspection rules, filtration, low-end instructions, only injection, transportation, storage and other requirements of the standard, suitable for SD8430 series composite light machine with radioactive material as the inner layer (hereinafter referred to as " Bag making machine "
2 Reference standards
Many standards include the current provisions and notes. The provisions of this standard are used in the market. When this note is published, all the standards are special: all standards are subject to public revision, promotion! This standard should be discussed for a long time. The possibility of using a new version
(019-1990 Packing and transportation graphic mark
GH 52261-156 Industry machine reduction seven parts: General drum technical conditions this elegant packaging policy development and preferential
GR/T6388- :98G
GR 9969.1-- 19SR
GB:1 13306-199]
GB/T J42S3-1993
GB:T 16769—:99?
Product instruction manual
Complete machine or twist and pull six
Membership of the technical institute for the determination of medium voltage level
QBTJ588.3-1992
Light city installation general technical kit
Recommended 1 agent mechanical paint uniform performance requirements
QRT 15881993
Light host packaging general non-technical requirements
QB:T 15885-1996
Type material heat test method QRT2358-1S98
3 Product classification
Basic bag making machine is digital circuit control (SD8430, SD843UA) or microcomputer control I AC servo system (SD8430B, SD843UC), variable speed, photoelectric tracking, tension dual operation control, electric heat sealing process with high-speed film sealing, middle sealing, middle sealing bag making machine. 3.2 Basic parameters of adhesive
1. China Light Industry Federation 2001-07-16 Approved 2001-11-01 Implementation
Minimum working speed
Working standard management
Average opening width
pa/min
+M year kw
Air force total cloud rate W
Equipment total A, kw
Capacity system
3.3 Model display method
QB/T2507—2001
SE8430
5DR430A
30--9n
SDS430E
SD843(C
30--120
Room Lake·-355
76-~ 4510
[20--629
For sealing
for school
for school code
for school code number, +parameter dynamic method sense number weaving change. Display deviation:
3.4Appearance size
two methods,
for school code
for school code number (for plastic bag making machine)
for bag making machine appearance (width and height, 935m×7200mm164Technical requirements
for special bag making machine%reputation manufacturing application Meet the requirements of G14253. 4.1 Appearance quality requirements
4.1.1 The edges of the parts should be neat and even, without obvious increase in the number of parts. 4.1.2 The parts with surface treatment (transmitter, chrome, etc.) should be smooth and even in color! 4.1.3 The outer surface should be smooth and even in color. 41.4 The brand should be clear, smooth, and even in color. KNrKAea-
4.2. Assembly quality
QB/T.25072001
4.2.1 The assembly seat shall comply with the provisions of 9B.T1588.3. 4.2.2 The movement and rotation of the motor shall be smooth and stable, and the phenomenon of Yuanyang limit shall be eliminated. 4.2.3 The joints shall be firm.
1.3 Electrical and safety requirements
4.3.1 The installation of electrical and electric heating loads shall be complete, in accordance with the US standard, and the electrical components and wires shall be firmly connected. The wire joints shall be marked according to the location. The oil should be removed and the insulation should be in good condition. 4.3.2 All the electrical equipment and the protective earthing circuit should be connected to the same voltage drop. The connection of the protective earthing circuit should be verified by connecting a 501Hz or 60Hz medium voltage, at least 10A, between the two pairs. The insulation voltage obtained when 500Vd.e is added between the power circuit and the protective earthing circuit should not be less than 4.3.4 All the circuits of the electrical equipment and the protective earthing circuit should be subjected to a withstand test of at least 1> time. 4.3.5 The heat dissipation components should be tested for faults. The protective frame that must be set up should be safe and reliable. 436 The whole machine should have a sliding power-off protection switch at the power-off section, and the action should be sensitive and efficient. 4.3.7 The transmission part should have an optimal protective cover to achieve safety. 4.4 The three-step transfer operation should meet the requirements of this standard. 4.1 The lower body resistance should be in compliance with the requirements. 4.42 The whole machine should not have abnormal operation, and the noise level should not be too high. 85B (A) 4.4.3 The motor heater should have a high degree of resistance to the actual temperature of the whole machine. The temperature monitoring system should be maintained at the actual temperature of the whole machine. 4.5 The light package should be Request
cold electric limit color standard thick bone should be flexible rescue, guarantee system absolute case set complete obvious response shift. 4.6 practical performance requirements
4.E, 1 volume you firmly style in accordance with the introduction of Table 1.
4.E.2 ten heart capacity with shares of people T. work speed caused by the resistance of the section, and should be checked in accordance with Table 1 frequency. 4.6.3 system should be flat, mouth, shape.
4.6.4 garbage compensation cooked Ma should be in accordance with Table 2: (when the shear film is pulled apart by the force of its heat platform strong) Table 2
with the law of the division of the separation ((P) multilayer
vertical 7,(PF> internal properties: the inner and outer layers of the material are made of a single material, Figure 4.6.5 The size reduction should comply with the requirements of Table 3 3 0.4--n 35 .3~I 1-1 0.60 2-~ 113 Total strength N/15mm 5 Test method 3~30℃ 51 Appearance quality inspection DB/T 2507 —2001
SD3430
SD430A
SES430R
SD84300
5.1.1 The symmetry of the edges of the joint surfaces and the processing of the surface shall be in accordance with the provisions of 4.1.1.4.1.2:
5.1.2 The quality of the painted surface shall be in accordance with the provisions of QBT15%8.41. The folding feeling shall comply with the provisions of 4.13. 5.13 The type and display of the signs shall comply with the relevant provisions of 1336. The date of inspection of the position of the certificate H and the provisions of 4.1.4 of the North avoidance box
5.2 The non-use date of the certificate of the digital change
521 shall be controlled by the hand feeling control test, and the provisions of 4.2.2 shall be specified in 5 2.2 This change of sex due to sex attention two love inspection, should be combined with 1 2.5 of the period is 53 from the full insurance question || tt || 5.31, hot road safety month thank you and the inspection of the whole, the combination of 4.3.1 of the knowledge of 53.2 in the table according to (7B Hall 536.1.3, 294 violation of the inspection age, and should comply with 4.3211.3, 431 ±Now stipulated,
5.3.3 The electric heating parts shall be installed and installed safely, and the new ones shall be collected and cleaned. The parts shall be tested by hand. The provisions of 4 shall be met. The total power supply of the machine shall be fully utilized. The power supply of the machine shall be fully utilized. The machine shall be tested and tested by hand ... Test conditions
) Increase the illumination to not less than 01x:
All temperature control meters should be fully operational:) Work according to Table 1 or 4.4.1 requirements with the quantity gradually increasing, the operating time should be not less than 2h, 5.4.2 Reduce the test items and methods
a) Listen to the sound of the treasure is not correct:
b) Noise power level measurement by 6B/1679: It should meet the requirements of 4.4.2:) The error correction test should meet the requirements of 4.4.3, 6.5 Light horse test
5.5.3 The test conditions should meet the requirements of 5.4.1. 55? The reliability test of the photoelectric tracking color standard should be carried out during the performance test, and the color standard should be used for testing, the time should be not less than 5min, and the error test should meet the requirements of 4.5. 4
-+TY KNrKAca-
5.6 Performance test
8/T 2507—2001
5.6.1 Bag type and quality test by visual inspection: should meet the requirements of 4.6.E: 4.6.3. 5.6.2 Production capacity test
a, the actual production quantity is displayed on the display screen: b) The working speed is calculated according to formula 1).
y=0.0011.
一1 speed, m/min:
Where:
一1 (piece) bag length,
O…, actual production quantity, the calculated value is taken as the speed measurement value, and the annual result meets the requirements of Table 1 and 4.6.2. 5.6.3 The heat seal strength of the bag shall be in accordance with QB/T2358, and the result shall comply with the requirements of Table 1 or 4.6.4. 5.6. + Length deviation and inspection: turn off the automatic measurement source, and the length deviation of the continuous length measurement (except for the brush error) shall comply with the requirements of Table 3 or 4.6.5. h) Width error inspection: point measurement shall comply with the requirements of Table 3 or 4.6.5. 6. Inspection and dynamic test: the test results shall be consistent with the requirements of Table 3 or 4.6.5. 6.1-Testing
6.11 The product testing department will consult with the customer, and the test results are as follows: The product testing department can be limited to 0.1 2 J, 9 months 5 4.14.2. 4.1.1. -5. -6, 5.1. 525.3,4. 5.5. 5.6 law to implement full inspection (4.6 system 5 heart stop heat demand heat letter, more than the goods to 52 type rush inspection || tt || 6.2! The most likely hunting situation, become or.) New. "Product or old product transfer," production trial finalization: b) After formal production, the structure, color, "artificial light change, may call the product stove function:) Stop normal production, every two years law: less national case with each mechanism of the device into the type of inspection fee request time 622 Shenzhen type inspection finalization space in H: inspection of selected products in the fraud machine plug-in to check the number According to the provisions of Table 4, the inspection items are all in accordance with the requirements of 4.1~4.6 of this specification. 6.3 Judgment rules Table 4 Sample purchase 6.3.1 If there is one item that does not meet the factory inspection items, the product is judged to be unqualified. 6.3.2 Type inspection If there is any item that does not meet the requirements, the product shall be considered unqualified. 6.3.2 If there is any item that does not meet the requirements of Table 4, the product shall be considered unqualified. Marking and instruction manual 7. 1 Marking QB/T 2507- 2001 Including the package transportation graphic mark and the transport station collection and delivery mark. 1.t The packaging graphic mark is "on the top", "handle with care", "center of gravity", "start from here", "burst", etc., and shall comply with the provisions of 9.
1.2 The markings on the packaging and delivery shall comply with the provisions of G/T6388: The markings on the packaging box shall include the following: a) Model and name of the manufacturer:
Export number:
0) Packing date:
d) Packing appearance (length, width, and meaning);
e) Clean leather and wool:
Name of the receiving truck and the destination station:
g Shipping unit:
h) Number of shipments.
7.1.3 The markings on the packaging box shall be in oil and ink, and the handwriting shall be clear and the ink shall be uniform, beautiful and durable. 12 The product markings shall comply with the provisions of G096.
Daily packaging, transportation, storage
Bar.1 Bags
8.1.1 Packaging (Q/1585.5 regulations. .1.2 Bag milk should be packed in pressure packaging boxes. During the transportation and sales of the bag making machine before leaving the factory, it must be operated according to the various signs on the packaging. 8.3 Storage
The machine should be stored in the case and should be kept as follows: the storage place should have construction facilities, the storage period is one month, and the box should be checked and the anti-rust oil should be replaced. YIKNEY KAa3 The electric heating parts shall be installed safely and safely, and the new ones shall be collected under the conditions of total disconnection. The parts shall be cleaned and tested by hand. The requirements of clause 4.534 shall be kept in mind that the total power supply of the machine shall be fully automatic and the production efficiency shall be fully guaranteed. The whole machine shall be disconnected under the conditions of total disconnection. A "test according to the ratio" shall be carried out for at least seven or more times; and it shall comply with the provisions of 4.3.6. 5.3.5 The performance of the protective cover of the transmission part shall be tested from the beginning of the day and shall comply with the provisions of 4.3.7. 54 Operation test
5. 4.1 Test conditions
1) The illumination shall be increased to not less than 0.1x:
All temperature control instruments shall enter normal working state: 1) Operate according to the requirements of Table 1 or 4.4.1 with the quantity gradually increasing. The running time shall be not less than 2h. 5.4.2 Reduction of test items and methods
a) Listen to the abnormal sound:
b) Noise power level measurement according to 6B/1679: It shall comply with the provisions of 4.4.2: 1) The error detection and overflow inspection shall comply with the relevant provisions of 4.4.3. 6.5 Light test
5.5.3 The test conditions shall comply with the provisions of 5.4.1. 55? The reliability test of photoelectric tracking color mark should be carried out during the performance test. The color mark should be used for testing for not less than 5 minutes. The difference between the production and packaging should meet the requirements of 4.5. 5.6 Performance test 8/T 2507—2001 5.6.1 The bag type and the quality of the bag should be visually inspected by hand: it should meet the requirements of 4.6.E: 4.6.3. 5.6.2 Production capacity test a. The actual production quantity is displayed on the display screen: b. The working speed is calculated according to formula 1).
y=0.0011.
一1 speed, m/min:
Where:
一(piece) bag length,
O…, number of pieces, the calculated value is taken as the speed measurement value, and the result shall meet the requirements of Table 1 or 4.6.2. 5.6.3 The heat seal strength of the sealed bag shall be in accordance with QB/T2358, and the result shall meet the requirements of Table 1 or 4.6.4. 5.6. + Dimension accuracy test
Length deviation and inspection: turn off the automatic measurement source, and the length deviation of the continuous piece is measured by the ruler (except for the brush error), which shall meet the requirements of Table 3 or 4.6.5: h) Width error inspection: point ruler measurement shall meet the requirements of Table 3 or 4.6.5. 6 Inspection Tree
No interval rate, competitive risk separation test and dynamic mode. 6.1-Metal Inspection
6.11 All product inspection departments will consult with the rear, and the output: limited to 0.1 2 J, 9 months 5 4.14.2. 4.1.1. -5. -6, 5.1. 525.3,4. 5.5. 5.6 law to implement full inspection (4.6 system 5 heart stop heat demand heat letter, more than the goods to 52 type rush inspection || tt || 6.2! The most likely hunting situation, become or.) New. "Product or old product transfer," production trial finalization: b) After formal production, the structure, color, "artificial light change, may call the product stove function:) Stop normal production, every two years law: less national case with each mechanism of the device into the type of inspection fee request time 622 Shenzhen type inspection finalization space in H: inspection of selected products in the fraud machine plug-in to check the number According to the provisions of Table 4, the inspection items are all in accordance with the requirements of 4.1~4.6 of this specification. 6.3 Judgment rules Table 4 Sample purchase 6.3.1 If there is one item that does not meet the factory inspection items, the product is judged to be unqualified. 6.3.2 Type inspection If there is any item that does not meet the requirements, the product shall be considered unqualified. 6.3.2 If there is any item that does not meet the requirements of Table 4, the product shall be considered unqualified. Marking and instruction manual 7. 1 Marking QB/T 2507- 2001 Including the package transportation graphic mark and the transport station collection and delivery mark. 1.t The packaging graphic mark is "on the top", "handle with care", "center of gravity", "start from here", "burst", etc., and shall comply with the provisions of 9.
1.2 The markings on the packaging and delivery shall comply with the provisions of G/T6388: The markings on the packaging box shall include the following: a) Model and name of the manufacturer:
Export number:
0) Packing date:
d) Packing appearance (length, width, and meaning);
e) Clean leather and wool:
Name of the receiving truck and the destination station:
g Shipping unit:
h) Number of shipments.
7.1.3 The markings on the packaging box shall be in oil and ink, and the handwriting shall be clear and the ink shall be uniform, beautiful and durable. 12 The product markings shall comply with the provisions of G096.
Daily packaging, transportation, storage
Bar.1 Bags
8.1.1 Packaging (Q/1585.5 regulations. .1.2 Bag milk should be packed in pressure packaging boxes. During the transportation and sales of the bag making machine before leaving the factory, it must be operated according to the various signs on the packaging. 8.3 Storage
The machine should be stored in the case and should be kept as follows: the storage place should have construction facilities, the storage period is one month, and the box should be checked and the anti-rust oil should be replaced. YIKNEY KAa3 The electric heating parts shall be installed safely and safely, and the new ones shall be collected under the conditions of total disconnection. The parts shall be cleaned and tested by hand. The requirements of clause 4.534 shall be kept in mind that the total power supply of the machine shall be fully automatic and the production efficiency shall be fully guaranteed. The whole machine shall be disconnected under the conditions of total disconnection. A "test according to the ratio" shall be carried out for at least seven or more times; and it shall comply with the provisions of 4.3.6. 5.3.5 The performance of the protective cover of the transmission part shall be tested from the beginning of the day and shall comply with the provisions of 4.3.7. 54 Operation test
5. 4.1 Test conditions
1) The illumination shall be increased to not less than 0.1x:
All temperature control instruments shall enter normal working state: 1) Operate according to the requirements of Table 1 or 4.4.1 with the quantity gradually increasing. The running time shall be not less than 2h. 5.4.2 Reduction of test items and methods
a) Listen to the abnormal sound:
b) Noise power level measurement according to 6B/1679: It shall comply with the provisions of 4.4.2: 1) The error detection and overflow inspection shall comply with the relevant provisions of 4.4.3. 6.5 Light test
5.5.3 The test conditions shall comply with the provisions of 5.4.1. 55? The reliability test of photoelectric tracking color mark should be carried out during the performance test. The color mark should be used for testing for not less than 5 minutes. The difference between the production and packaging should meet the requirements of 4.5. 5.6 Performance test 8/T 2507—2001 5.6.1 The bag type and the quality of the bag should be visually inspected by hand: it should meet the requirements of 4.6.E: 4.6.3. 5.6.2 Production capacity test a. The actual production quantity is displayed on the display screen: b. The working speed is calculated according to formula 1).
y=0.0011.
一1 speed, m/min:
Where:
一(piece) bag length,
O…, number of pieces, the calculated value is taken as the speed measurement value, and the result shall meet the requirements of Table 1 or 4.6.2. 5.6.3 The heat seal strength of the sealed bag shall be in accordance with QB/T2358, and the result shall meet the requirements of Table 1 or 4.6.4. 5.6. + Dimension accuracy test
Length deviation and inspection: turn off the automatic measurement source, and the length deviation of the continuous piece is measured by the ruler (except for the brush error), which shall meet the requirements of Table 3 or 4.6.5: h) Width error inspection: point ruler measurement shall meet the requirements of Table 3 or 4.6.5. 6 Inspection Tree
No interval rate, competitive risk separation test and dynamic mode. 6.1-Metal Inspection
6.11 All product inspection departments will consult with the rear, and the output: limited to 0.1 2 J, 9 months 5 4.14.2. 4.1.1. -5. -6, 5.1. 525.3,4. 5.5. 5.6 law to implement full inspection (4.6 system 5 heart stop heat demand heat letter, more than the goods to 52 type rush inspection || tt || 6.2! The most likely hunting situation, become or.) New. "Product or old product transfer," production trial finalization: b) After formal production, the structure, color, "artificial light change, may call the product stove function:) Stop normal production, every two years law: less national case with each mechanism of the device into the type of inspection fee request time 622 Shenzhen type inspection finalization space in H: inspection of selected products in the fraud machine plug-in to check the number According to the provisions of Table 4, the inspection items are all in accordance with the requirements of 4.1~4.6 of this specification. 6.3 Judgment rules Table 4 Sample purchase 6.3.1 If there is one item that does not meet the factory inspection items, the product is judged to be unqualified. 6.3.2 Type inspection If there is any item that does not meet the requirements, the product shall be considered unqualified. 6.3.2 If there is any item that does not meet the requirements of Table 4, the product shall be considered unqualified. Marking and instruction manual 7. 1 Marking QB/T 2507- 2001 Including the package transportation graphic mark and the transport station collection and delivery mark. 1.t The packaging graphic mark is "on the top", "handle with care", "center of gravity", "start from here", "burst", etc., and shall comply with the provisions of 9.
1.2 The markings on the packaging and delivery shall comply with the provisions of G/T6388: The markings on the packaging box shall include the following: a) Model and name of the manufacturer:
Export number:
0) Packing date:
d) Packing appearance (length, width, and meaning);
e) Clean leather and wool:
Name of the receiving truck and the destination station:
g Shipping unit:
h) Number of shipments.
7.1.3 The markings on the packaging box shall be in oil and ink, and the handwriting shall be clear and the ink shall be uniform, beautiful and durable. 12 The product markings shall comply with the provisions of G096.
Daily packaging, transportation, storage
Bar.1 Bags
8.1.1 Packaging (Q/1585.5 regulations. .1.2 Bag milk should be packed in pressure packaging boxes. During the transportation and sales of the bag making machine before leaving the factory, it must be operated according to the various signs on the packaging. 8.3 Storage
The machine should be stored in the case and should be kept as follows: the storage place should have construction facilities, the storage period is one month, and the box should be checked and the anti-rust oil should be replaced. YIKNEY KAa6 All position requirements. Production
Sampling
6.3 Judgment rules
Table 4 Sample purchase
6.3.1 If there is one item that does not meet the factory inspection, the product is judged to be unqualified. 6.3.2 Type inspection, if there is one item that does not meet the requirements, it should be submitted to the requirements of Table 4. If the updated test piece still does not meet the requirements, the batch of products is unqualified.
Marking, instruction manual
7. 1 Marking
QB/T 2507- 2001
Including the packaging terminal transport icon mark and the transport station collection and delivery mark. 1.t The packaging delivery icon mark is "on the driver's seat", "handle with care", "center of gravity", "start from here", "burst", etc., and should comply with the provisions of G/T6388. 1.2 The packaging delivery and receipt mark network complies with the provisions of G/T6388: The packaging box surface mark should include the following: a) production model and name:
export number:
0) packaging date:
d) packaging new shape (length, width and shape);
e) net leather and wool:
receiving truck location name:
g shipping unit:
h) number of shipments. ||tt ||7.1.3 The markings on the packaging box should be in oil and ink, and the writing should be clear and the ink should be even, beautiful and durable. 12 The product specifications should comply with the current provisions of G096.
Daily packaging, transportation and storage
Packing
8.1.1 Packaging (Q/1585.5). 1.2 The bagged milk should be packed in a pressure packing box. During the transportation and sales of the machine from the factory to the home, it must be operated according to the various signs on the packing box. 8.3 Storage
The machine should be stored in the box and should be kept as follows: the storage place should have construction facilities, the storage period should be one month, and the box should be checked and the anti-rust oil should be replaced. YIKNEY KAa6 All position requirements. Production
Sampling
6.3 Judgment rules
Table 4 Sample purchase
6.3.1 If there is one item that does not meet the factory inspection, the product is judged to be unqualified. 6.3.2 Type inspection, if there is one item that does not meet the requirements, it should be submitted to the requirements of Table 4. If the updated test piece still does not meet the requirements, the batch of products is unqualified.
Marking, instruction manual
7. 1 Marking
QB/T 2507- 2001
Including the packaging terminal transport icon mark and the transport station collection and delivery mark. 1.t The packaging delivery icon mark is "on the driver's seat", "handle with care", "center of gravity", "start from here", "burst", etc., and should comply with the provisions of G/T6388. 1.2 The packaging delivery and receipt mark network complies with the provisions of G/T6388: The packaging box surface mark should include the following: a) production model and name:
export number:
0) packaging date:
d) packaging new shape (length, width and shape);
e) net leather and wool:
receiving truck location name:
g shipping unit:
h) number of shipments. ||tt ||7.1.3 The markings on the packaging box should be in oil and ink, and the writing should be clear and the ink should be even, beautiful and durable. 12 The product specifications should comply with the current provisions of G096.
Daily packaging, transportation and storage
Packing
8.1.1 Packaging (Q/1585.5). 1.2 The bagged milk should be packed in a pressure packing box. During the transportation and sales of the machine from the factory to the home, it must be operated according to the various signs on the packing box. 8.3 Storage
The machine should be stored in the box and should be kept as follows: the storage place should have construction facilities, the storage period should be one month, and the box should be checked and the anti-rust oil should be replaced. YIKNEY KAa
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.