Packaging－Transport packages－Compression test method

This standard specifies the main performance requirements, test procedures and test report contents of the test equipment used in the pressure test of transport packages. This standard is applicable to the assessment of the compressive strength of transport packages when subjected to pressure and the protection of the packaging to the contents. It can be used as a single test or as part of a series of tests. GB/T 4857.4-1992 Packaging and transport package pressure test method GB/T4857.4-1992 Standard download decompression password: www.bzxz.net
This standard specifies the main performance requirements, test procedures and test report contents of the test equipment used in the pressure test of transport packages. This standard is applicable to the assessment of the compressive strength of transport packages when subjected to pressure and the protection of the packaging to the contents. It can be used as a single test or as part of a series of tests.

National Standard of the People's Republic of China
Packaging-Transport packages-Compression test method
Packaging-Transport packages-Compression test methodGB/T 4857.4-
ISO 28721985
Replaces GB4857.4-84
This standard is equivalent to the international standard ISO2872-1985 "Packaging-Complete, fully filled transport packages-Pressure test". Subject content and scope of application
This standard specifies the main performance requirements, test procedures and test report contents of the test equipment used in the pressure test of transport packages.
This standard is applicable to the assessment of the compressive strength of transport packages when subjected to pressure and the protection ability of the packaging to the contents. It can be used as a single test or as part of a series of tests. 2 Reference standards
GB/T4857.17 General principles for compiling performance test outlines for packaging and transport packages GB3538 Marking methods for various parts of transport packages GB/T4857.2 Temperature and humidity adjustment treatment for packaging and transport packages GB/T4857.18 Quantitative data for compiling performance test outlines for packaging and transport packages 3 Test principle
Place the test sample between the two parallel pressure plates of the test machine, then apply pressure evenly, and record the load and pressure plate displacement until the test sample breaks, or the load or pressure plate displacement reaches the predetermined value. 4 Test equipment
4.1 Pressure testing machine
The pressure testing machine is driven by an electric motor, mechanical transmission or hydraulic transmission, and the pressure plate type must be able to enable one or two pressure plates to move at a relative speed of 10±3mm/min to apply pressure to the test sample. The platen should be flat. When the platen is placed horizontally, the height difference between the lowest point and the highest point of the platen should not exceed 1mm: the size of the platen should be larger than the size of the test sample in contact with it, and the maximum stroke between the two platens should be larger than the height of the test sample. The platen should be hard. When 75% of the rated load of the test machine is applied to a 100mm×100mm×100mm hardwood block at the center of the platen, the deformation of any point on the platen should not exceed 1mm. This block should have sufficient strength to withstand this load without breaking. The lower platen must always remain horizontal, and its horizontal inclination should be kept within 20% of the test during the entire test. The upper platen should be firmly installed, and its horizontal inclination should be kept within 20% of the test during the entire test; or the center of the upper platen should be installed on a universal joint so that it can tilt freely in any direction. 4.2 Recording device
The load error recorded by the recording device shall not exceed 2% of the applied load. The displacement error of the platen is 1mm. Approved by the State Administration of Technical Supervision on November 25, 1992 and implemented on June 1, 1993
5 Test procedure
5.1 Preparation of test samples
GB/T 4857.4—
Prepare test samples in accordance with the provisions of GB/T4857.17. The number of test samples is generally not less than 3. 5.2 Numbering of various parts of test samples
Number various parts of test samples in accordance with the provisions of GB3538. 5.3 Pretreatment of test samples
Select a condition for temperature and humidity pretreatment of test samples in accordance with the provisions of GB/T4857.2. 5.4 Temperature and humidity conditions during the test
The test should be carried out under the same temperature and humidity conditions as those during the pretreatment. If the same conditions cannot be achieved, the test should be carried out under temperature and humidity conditions as close to them as possible.
5.5 Selection of test strength value
Select the test strength value according to the provisions of GB/T4857.18. 5.6 Test steps
5.6.1 Plane pressure testWww.bzxZ.net
5.6.1.1 Record the temperature and humidity of the test site. 5.6.1.2 Place the test sample in the center of the lower pressure plate according to the predetermined state, so that the upper pressure plate and the test sample are in contact. First add an initial load of 220N to ensure good contact between the test sample and the upper and lower pressure plates. Adjust the recording device and use this as the starting point for displacement recording. 5.6.1.3 Move the pressure plate distance uniformly at a speed of 10±3mm/min. Pressure should be applied to one of the following situations: the compression load does not reach the predetermined value and the test sample breaks; a.
b. The test sample is deformed in size or the compression load reaches the predetermined value. 5.6.2 Diagonal and edge pressure test
If it is necessary to measure the diagonal and edge pressure resistance of the test sample, a pressure testing machine with both upper and lower pressure plates that cannot tilt freely must be used.
The test steps are the same as those for the plane pressure test.
5.6.3After the test, check the damage of the packaging and contents according to relevant standards and regulations, and analyze the test results. 6 Test report
The test report shall include the following contents:
Name, specification, model, quantity, etc. of the contents; if simulated contents are used, detailed description shall be given; number of test samples;
Detailed description of the name, size, structure and material specifications of the packaging container, accessories, cushioning pads, supports, fixing methods, sealing, bundling status and other protective measures;
The mass of the test sample and contents in kilograms; pretreatment temperature, relative humidity and time; temperature and relative humidity of the test site;
Placement status of the test sample during the test; test phases in series tests; description of test equipment and instruments;
Graphs or data of pressure and deformation of each test sample during the test and the load-bearing duration; record any observed phenomena that can help correctly interpret the test results; record the inspection results after the test;
Submit a test result analysis report;
GB/T 4857. 4—92
Describe the differences between the test method used and this standard; test date, tester’s signature, and test unit’s seal. n
Additional explanation:
This standard was proposed by the Ministry of Machinery and Electronics Industry of the People’s Republic of China. This standard was drafted by the Electronic Standardization Institute of the Ministry of Machinery and Electronics Industry. The main drafters of this standard are Fang Lina and Xu Yunchi. 261
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.