GB 8394-1987 Pommel horse

This standard applies to pommel horses for gymnastics competitions and general practice. GB 8394-1987 Pommel Horse GB8394-1987 Standard download decompression password: www.bzxz.net

National Standard of the People's Republic of China
Pommelled horse
This standard applies to pommel horses for gymnastics competition and general practice. This standard adopts the 1979 International Gymnastics Federation gymnastics equipment standard. 1 Product classification
1.1 Pommel horses are divided into the following types according to their usage: a. Competition pommel horses;
b. General practice pommel horses.
1.2 Basic size parameters shall comply with the provisions of Figure 1 and Table 1. Figure 1
Horse face height h
Basic size
1100~1500
Approved by the Ministry of Light Industry of the People's Republic of China on December 10, 1987
Limit deviation
UDC 685.64
GB8394-87
Basic size
1100~1350
Limit deviation
Implementation on June 1, 1988
Inner distance S
Ring section diameter Φ
Lifting spacing
Saddle ring outer width b:
Saddle ring inner width b2
1.3 The main raw materials shall comply with the requirements of Table 2. Part Name
Horse Body
Technical Requirements
GB 8394—87
Continued Table 1
Basic Dimensions
400～450
Limit Deviation
Competition Type
Cow Leather or Other Materials of Similar Texture
Latex Sponge or Other Materials of Similar Texture The basic dimension parameters of the pommel horse shall be as specified in Figure 1 and Table 1. 2.1
The technical indicators shall comply with the provisions of Table 3.
Indicator name
Smoothness
Hardness
Compatibility
Corrosion resistance of electroplating layer
Surface quality
Interchangeability
Ordinary practice type
Basic size
400~450
280, 310
185, 224
Limit deviation
Ordinary practice type
Artificial leather Or other materials with the same texture
Felt or other materials
Ordinary practice type
Smooth landing, no warping
The horse's body is soft and hard, and feels comfortable; the whole body is uniform and smooth, the inner and outer tubes are properly tight, and the movable parts are flexible to use. The corrosion resistance level is not less than level 7
a. The leather surface has uniform color, and knife wounds, snake eyes, and injuries are not allowed
b. The spray paint or baking paint has a clear color, without paint streaks, wrinkles and dirty spots. The saddle ring must be firm and not shake. It must be perpendicular to the horse body and interchangeable. The main dimensions are shown in Figure 245. The corrosion resistance level must not be lower than level 5. The color of the artificial leather surface must be uniform and without damage. The paint color must be uniform and uniform, without paint streaks or exposed bottom. 070. 3 Test method. GB8394-87. 3.1 Specifications and dimensions must be measured with a vernier caliper, steel tape measure or special ruler with the same indication error. 3.2 Stability: Place the saddle horse on the reference plane and push it by hand without swaying or shaking. 3.3 Softness and hardness: Determine by hand feel. 3.4 The corrosion resistance of the electroplating layer must be tested for 24 hours according to GB5938 "Neutral Salt Spray Test (NSS) Method for Corrosion Resistance of Metal Coatings and Chemically Treated Layers of Light Industrial Products", and rated according to GB5944 "Evaluation of Corrosion Test Results of Metal Coatings of Light Industrial Products". 3.5 Compatibility is measured by hand feel.
3.6 Surface quality is checked visually or by comparison with actual samples. 3.7 Interchangeability The saddle ring is firm and does not shake, which is measured by hand feel. 4 Inspection rulesbZxz.net
4.1 The inspection of batch products is divided into batch inspection and periodic inspection. 4.2 Batch inspection
4.2.1 Batch inspection is carried out in accordance with the one-time sampling plan of general inspection level I in GB2828 "Batch inspection counting sampling procedure and sampling table (applicable to the inspection of continuous batches)".
4.2.2 The items and clauses of batch inspection, test method clauses and AQL values ​​shall be in accordance with the provisions of Table 4: Table 4
Basic dimensional parameters
Smoothness
Hardness
Compatibility
Surface quality
Interchangeability
4.3 Periodic inspection
Clause of this standard
Test method clause
Competition type
Ordinary practice type
4.3.1 The samples for periodic inspection must be randomly selected from the samples that have passed the batch inspection and all of them must be inspected according to the batch inspection items. If unqualified products are found, they should be replaced with qualified products. 4.3.2 Periodic inspection shall be carried out every six months, and shall also be carried out when the design, key process, main raw materials are changed or when production is resumed after suspension for more than three months.
4.3.3 Periodic inspection shall be in accordance with the provisions of the single sampling plan for the discrimination level II and the judgment array (12) in GB2829 "Periodic Inspection Counting Sampling Procedure and Sampling Table (Applicable to the Inspection of Stability of Production Process)". 4.3.4 The items and clauses of periodic inspection, the test method clauses and their RQL values ​​shall be in accordance with the provisions of Table 5. Table 5
Corrosion resistance of electroplating layer
5 Marking, packaging, transportation, storage
Clause of this standard
Test method clause
5.1 Marking: The product shall have a trademark, factory name, certificate of conformity, product manual, and date of manufacture. Competition type
RQL, %
Ordinary practice type
GB8394—87
2 Packaging: According to the different conditions in each region, choose packaging materials to protect the product. 5.2
5.3 Transportation: Do not expose to rain, sun or moisture during transportation. Handle with care and avoid squeezing or collision. 5.4 Storage: The warehouse should be ventilated and dry (do not store products in the open air) and properly stored. Additional Notes:
This standard was proposed by the Ministry of Light Industry of the People's Republic of China and is under the jurisdiction of the National Stationery and Sports Goods Standardization and Quality Inspection Center. This standard was drafted by Shanghai Stationery and Educational Goods Industry Research Institute, Tianjin Chunhe Sports Goods Factory, Shanghai Sports Equipment Factory, Guangzhou Dongfang Sports Equipment Factory, Beijing Sports Equipment Factory, and Chengdu Sports Equipment Factory.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.