QB/T 2209-1996 Assorted hammers

This standard specifies the type, basic dimensions, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of the hammer and accessories of the assorted hammer. This standard is applicable to the assorted hammers used for ordinary measuring tool maintenance and household use. QB/T 2209-1996 Assorted Hammer QB/T2209-1996 Standard download decompression password: www.bzxz.net

QB/T2209--1996
This standard is revised based on the Ministry of Light Industry of the People's Republic of China Standard SG217-1980 "Assorted Hammers". According to the actual needs of the product, this standard changes the wide and narrow screw rods in the original standard assorted hammer accessories to slotted screw rods and cross-slot screw rods.
This standard changes the hardness of the screw rod in Article 4 of the original standard technical conditions from HRC45~50 to HRC48~54. This standard adds Article 4.5 on the assembly requirements of accessories and handles, and Article 4.6 on the connection requirements of hammer heads, handles, side hole screws, and back cover threads, replacing the original standard thread accuracy and the matching tolerance of accessories and handle holes. From the date of implementation, this standard will also replace SG217-1980. This standard is proposed by the Quality Standards Department of the China Light Industry Federation. This standard is under the jurisdiction of the National Tool Hardware Standardization Center. The drafting units of this standard are: Shanghai Tool Industry Research Institute, Shanghai Qianjin Machinery Factory. The main drafters of this standard are: Lu Xialing and Xu Haiwen. 575
1 Scope
Light Industry Standard of the People's Republic of China
Assorted Hammers
QB/T2209---1996
This standard specifies the types, basic dimensions, technical requirements, test methods, inspection regulations, markings, packaging, transportation and storage of assorted hammers and accessories.
This standard is applicable to assorted hammers used for ordinary measuring tool maintenance and household use. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T 230—1991
Metallic Rockwell hardness test method
GB/T699-1988Technical conditions for high-quality carbon structural steelGB/T1298—1986Technical conditions for carbon tool steelGB/T 2828---1987
Batch inspection counting sampling procedures and sampling tables (applicable to inspection of continuous batches)GB/T 5305--1985
Packaging, marking, transportation and storage of hand toolsYB(T)1-1981Recommended standard for high carbon chromium bearing steel3 Types and basic dimensions
The types and basic dimensions of assorted hammers shall comply with Figure 1. Unit: mm
162±1
1—Hammer head; 2—Side hole screw; 3-Hammer handle; 4—Back cover Figure 1 Assorted hammers
3.2 The assorted hammers should have five accessories: triangular file, awl, wood chisel, slotted screw shank and cross-slotted screw shank. The types and basic dimensions of the accessories are shown in Figure 2.
Approved by China Light Industry Federation on March 22, 1996
Implementation from December 1, 1996
Slotted screw shank
Cross-slotted screw shank
QB/T2209-1996
/ 10° (max)
No. 1 slot shank
Figure 2 Assorted hammer accessories
3.3 The marking of the assorted hammer consists of the product name and standard number. Example: Assorted hammer QB/T2209
4 Technical requirements
4.1 Materials of assorted hammers and accessories are shown in Table 1. og-s
90 g- s
80 g- ss
Unit: mm
Triangular file
Awl wood chisel
Screw rod
QB/T 2209--1996
High-quality carbon structural steel
Carbon tool steel
Chromium bearing steel
High-quality carbon structural steel
High-quality carbon structural steel
The heat treatment hardness of hammer head and accessories is shown in Table 2. Table 2
Flange file
Screw rod
Awl, wood chisel
54~~59
T10, T12
Standard code
GB/T699
GB/T1298
YB(T)1
GB/T 699
GB/T 699
Testing position
Within 10mm from the end
Within 12mm from the blade
4.3 The knurling on the handle, the head of the side hole screw and the surface of the back cover should be clear and should not have obvious bruises. 4.4 The surface of the hammer should be electroplated or blackened, and its color should be bright and uniform, without rust and exposed bottom. 4.5 The accessories should be easily installed in the handle hole. 4.6 The threaded connection of the hammer head, handle, side hole screw and back cover shall be flexible. 4.7 Accessories shall comply with the following provisions:
4.7.1 The main file pattern shall be clear and sharp, without curling, skipping teeth or repeated teeth. 4.7.2 The cutting edge of the wood chisel shall be flat, without cracks or curling. 4.7.3 The tip of the awl shall be sharp, without cracks or burrs. 4. 7. 4
The screw rod shall comply with the test torque specified in Table 3. Table 3
… Cross-slot screw rod
Cross-slot screw rod
5 Test method
Test torque
5.1 The hardness test shall be carried out in accordance with the provisions of GB/T230 and the test parts specified in Table 2. 5.2 The surface and appearance quality shall be inspected by visual inspection. 5.3 The connection quality shall be inspected by hand.
5.4 The basic dimensions shall be inspected with universal measuring tools.
5.5 The torque test of the screw rod is carried out on a special torque test device. The head of the screw rod is inserted into the test groove and torque is applied to the handle. After the test, the end of the screw rod shall not produce obvious permanent deformation. 578
6 Inspection and testing
QB/T2209--1996
6.1 Products must be inspected and qualified by the inspection department and accompanied by a product certificate before they can leave the factory. 6.2 The acceptance inspection of products shall be carried out according to the single sampling plan procedure specified in GB/T2828. The classification of non-conforming products, inspection items, qualified quality level AQL (number of non-conforming products per hundred units) and inspection level IL are shown in Table 4. Table 4
Non-conforming classification
Inspection items
Connection performance
Qualified quality level (AQL))bzxz.net
6.3 Products rejected after inspection can be resubmitted for acceptance after classification or refurbishment by the manufacturer. Marking, packaging, transportation, storage
The packaging, marking, transportation and storage of products shall comply with the provisions of GB/T5305. Inspection Level (IL)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.