GB 19159-2003 Liquefied petroleum gas for vehicles

This standard specifies the requirements, test methods, storage, marking, transportation, safety and health requirements for liquefied petroleum gas for vehicles. This standard applies to liquefied petroleum gas for vehicles. GB 19159-2003 Liquefied petroleum gas for vehicles GB19159-2003 Standard download decompression password: www.bzxz.net

This standard adopts the mandatory requirements of the Ministry of Industry and Information Technology, and the former GE19159—2003. This standard considers the European EN58, 1D43 military petroleum gas 3 and the American ASTMD1835199 certified petroleum gas 3. This standard replaces SY7548-1999 automotive liquefied petroleum gas. The main differences between this standard and SY75481998 are as follows: 1. This standard divides petroleum gas into No. 5, No. 2 and No. 3: 2. This standard changes the content of butene to the mass fraction of total olefin content not greater than 1: 3. The standard adds the control of the content of butene and stipulates that the mass fraction of butene should not exceed 9.5. This standard is proposed by China Petrochemical Corporation. This standard is a petroleum industry standard. The committee is responsible for the standardization of oil and gas and pipeline construction design. The responsible unit is China National Petroleum Corporation North China Branch, the approved unit is China Petrochemical Corporation Petrochemical Research Institute, China Petrochemical Corporation Beijing Yanzhi Branch Refinery, China Petrochemical Corporation Planning Institute The main drafters of this standard are Yu Qianchun, Bo Lihong, Zhang Zhiyun, Yang Shengxun, Shi Mingrun, Bian Jun, Bian Jiang, Duan Wei, Cheng Pengchun. Production 1 Fan Guo
Petroleum gas
The automotive fluids standard GR19159-2003 specifies the requirements, test methods, storage, marking, transportation, safety and chain health requirements for petroleum gas used in vehicles. This standard applies to petroleum gas fuel for vehicles. 2 Normative references The clauses in the following documents become the clauses of this standard through reference in the standard. For the referenced documents after the date of reference, all subsequent amendments (excluding the contents of the referenced documents) or revised versions are not applicable to this standard. However, the parties involved in the design of the automotive standard after the date of reference may use these documents. The latest version. For any undated referenced document, the latest version shall apply. 50 Steel Container
GB/6607 Petroleum Gas Pressure Determination Method (1.PG Method) G13 Hygienic Standard for Liquefied Petroleum Gas in Air G5/112573 Petroleum Gas Vapor Pressure and Relative Density Calculation C5:4193 Filling Specification for Petroleum Gas Cylinders
GB1239 Petroleum Gas Cylinders
SH/F0125 Liquefied Petroleum Gas Hydrogen Sulfide Test Head (7 Acid Lead Method) SH/ (221
Liquefied Petroleum Gas Relative Tightness Determination Method (Pressure Tightness Calculation) SH/ (2 Petroleum Gas Total Conformity Determination Method (Electromagnetic Recording Method) ST/T0230
Liquefied Petroleum Gas Filter Group Transparent Determination Pig, Color Increase Transport!
SH/T 0232
Liquid petroleum gas flake separation test
SE/233
3 Liquefied petroleum gas sample method
SH gate (M14 Industrial propane, butane component preparation method (gas sweeping color harmonic method! SY5985 Liquefied petroleum gas safety management
SYIT5U Oil and gas mountain petroleum gas total deficiency determination (chemical micro-reservoir method) SYT75U9, filter Baidi 4 sensor retention new method for the new technical gas iron tank truck safety management regulations liquefied gas caravan safety supervision system regulations pressure vessel safety technical supervision regulations
Current process of gas cylinder safety supervision
3 Product classification and brand
According to the different butane component content, automotive petroleum gas is divided into the following three brands of products:) No. 1 product It can be used with caution under the condition of above 21℃: 6) No. 2 product can be used under the condition of ambient temperature higher than: 10℃: 3) After the production, it can be used in the case of environmental humidity higher than 1℃. 1
B19159—2003
4 Requirements
4.1 The technical requirements of Jinzhou liquefied petroleum gas should comply with the provisions of Table 1 Technical requirements for automotive liquefied petroleum gas
Quality index
Hot pressure k
1 Institute and 1
Quality index
Effective density
Institute summary
Total olefins
"Diolefins (1.3-"diolefins)
English version of the picture ml/mmm.)
Oil Guiguantai
! Package, version
total research and consulting engineer mz
neck chemical ammonia
word this
position total flow is 1.3 production piece quality
these: while measuring the customer quality: 11 full statutory sample is the consulting existence management high requirement, number
of course can be rough GBTS6, when cutting time use GT6G2 specified above
you can use 20 method to measure at the hour position 510614 measurement 125 calculation, when using the measurement.
dThe total amount of available 5Y/7C3E decision - recently existing heat application SH/TU222 decision:: No.
Folk voice method
[ 6r02
S/T G514
RYTTESwwW.bzxz.Net
XI :3:
SH/T $222
SF/T 13E
2.2 In order to ensure the safe use of liquefied petroleum gas for vehicles, and the vehicle ionized petroleum gas does not contain obvious smell. The amount of excellent alcohol should be carefully observed, and the aldehydes, tetrahydrofuran, etc. should be added in a certain amount. When the concentration of oil and gas in the air reaches 24% below the good value, it can be detected.
5 Sampling
Sampling shall be carried out in accordance with SHI/T0235
6 Storage, marking, long-distance transmission
E.1 Storage
The commercial storage containers for automobile oil and gas shall comply with the current regulations of B15C, and the requirements of the safety technical supervision of non-executive vessels shall be met. The installation of filters on automobiles shall comply with the provisions of (17233) and the requirements of the gas safety supervision regulations. The filling of gas shall comply with the provisions of GH14.
E.2 Marking
The storage place of automobile gas shall comply with the current regulations, marking and standard: the storage place shall be equipped with 6.3.1 The vehicle shall comply with the requirements of the Safety Code for Liquefied Gas Vehicles and the Safety and Health Requirements for Gas Tank Vehicles. 6.3.2 The vehicle shall comply with the requirements of the Safety Code for Liquefied Gas Vehicles and the Safety and Health Requirements for Gas Tank Vehicles. 7.1 In the production, storage and use of this product, in addition to the provisions of this standard, the provisions of SY5385 shall be observed. 7.2 The places where this product is produced, stored and used shall be properly ventilated and shall be implemented in accordance with the provisions of G7115:8.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.